Mercury IoT Gateway Instructions

Mercury IoT Gateway

Specifications

• Configuration:
  • Display Physical Resolution
  • Brightness
  • Touch Panel
  • Contrast
  • Viewing Angle
• System Hardware:
  • Power Status
  • Reset Button
  • Power On/Off Button
  • Service Button
  • S/N, MAC Address
  • Micro SD Slot
  • O|O1, IOIO2 ports
  • GPIO
  • HDMI Output
  • Ear Jack
  • Power Input

Extended Cable Definition

Definition for IOIO1 and IOIO2 ports, including RS232, RS422, and RS485 connections with color coding.

Memory Card Instructions

1. Align and insert the memory card accurately to avoid damage. Loosen the card before removal.
2. Normal for the memory card to get hot during prolonged use.
3. Data damage risk if not used correctly, even during power loss or improper removal.

Operation Guide

1. Basic Operation: Press the User Key, Enter Password (123456), and Press Enter.
2. Network Settings: Access Settings > Network > Ethernet.
3. Program Malin1 IoT Platform: Access Activities, Set OWNER ID, Configure Parameters.
4. Parameter Setup: Key parameter name, Generate ID, Select Read/Write, Set Type/Unit, Configure MODBUS RTU settings.
5. Saved Parameters : Display saved parameters in a table.

FAQ (Frequently Asked Questions)

Q: What should I do if the memory card gets too hot?

• A: It is normal for the memory card to get hot during extended use. Ensure proper ventilation and avoid covering the device to prevent overheating.

Q: How can I ensure data integrity when using the memory card?

• A: Always align the memory card properly before insertion and removal. Avoid sudden power loss or improper removal to prevent data corruption.

Q: What is the significance of the GPIO connections?

• A: GPIO connections allow for input and output control on the device. Refer to the user manual for detailed GPIO functionality.

Specifications

OVERVIEW

Font Side

1. Power Status
2. Reset Button
3. Power On/Off Button
4. Service Button

Font Side

1. S/N, MAC Address
2. Micro SD Slot
3. O|O1, IOIO2 ports See“ Extended Cable Definition” for details )
4. GPIO (See“ Extended Cable Definition” for details )
5. HDMI Output
6. USB Port ×2
7. LAN Port ×2
8. Ear Jack
9. Power Input

Extended Cable Definition

IOIO1

• RS232 standard interface, connecting with DB9 standard cable to convert to 3×RS232 ports
• Com 3RS232
  • Com 4RS232
• Com 5RS232

IOIO2

• RS232 standard interface, connecting with DB9 optional cable to convert to 1×RS232, 1×RS422 and 1×RS485 ports
• Com 6RS232
  • Com 5RS422
• Com 6RS485
  • Red A White Z
• Black B Green Y
  • Red Positive Pole
• Black Negative Pole
• Note: RS232 and RS422 are alternatives for COM5.
• RS232 and RS485 are alternatives for COM6.
• It should match with a standard cable when using IOIO 1; Otherwise, there is a risk of a short circuit.

GPIO

Yellow

GPIO Output| GPIO5 GPIO6 GPIO7 GPIO8 GPIO9 GPIO10

Blue

GPIO GND| Black

Memory Card Instructions

1. The memory card and the card slot on the device are precision electronic components. Please align to the position accurately when inserting the memory card into the card slot to avoid of damage. Please slightly push the upper edge of the card to loosen it when removing the memory card, then pull it out.
2. It is normal when the memory card gets hot after a long time of working.
3. The data stored on the memory card may be damaged if the card is not used correctly, even if the power is cut off or the card is pulled out when reading data.

Operation Guide

Basic Operation Start

1. Press User
2. Key Password 123456
3. Press Enter

Network Settings

1. Press icon

   • Settings > Network > Ethernet

Program Malin1 IoT Platform

1. Press Activities
2. Press icon Malin1 IoT Platform
3. Key OWNER ID ( See “ Manual Platform ” for details )
4. PressSetting Parameter Please set up the parameter before start
5. Press the icon + Add the Parameter
6. Key parameter name
7. Auto gen parameter ID
8. Select Read or Write
9. Select parameter Type/Unit
10. Press Setting MODBUS RTU (See “ Sensor Manual ” for details)
11. Select Data Type  (See “ Sensor Manual ” for details)
12. Set Value of Limit High
13. Set Value of Limit Low
14. Select Enable (True) Or Disable (False) parameter
15. Press Save Button
16. Device IP address.
17. Device Port number.
18. Connection Timeout (ms).
19. Device/Module ID.
20. Function Code.
21. Register Address.
22. Data Length (word).
23. Convert Value Operator(+,-,*,/,none).
24. Convert Value Constance
25. Value for test write.
26. Connection Test.
27. Test Read.
28. Test Write.
29. Save.
30. Cancel
31. Saved parameters will be shown in the table.
32. Press the icon to register parameters to the M1 Platform
33. Press icon Back to Manu
34. Move-up parameters order.
35. Move down parameters order.
36. Save parameters order.
37. Press Home
38. Press Start
39. Press icon to see the real-time parameter value
    • Blue Color = Normal value
    • Purple   Color = Under Limit Low value
    • Red Color = Over Limit High value
    • M1 Connection Status

Power Off

Function Select

• Restart
• Suspend
• Power Off
• Log Out

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>