SOUNDEXTREME SEI-SETXLED Remote Control User Guide

SOUNDEXTREME SEI-SETXLED Remote Control

Specifications

• Model: SEI-SETXLED
• Wireless LED lighting controls
• RF 433MHz remote transmitter
• Remote Turn-On Output
• Supports 44 Modes
• Supports up to 4 LED lighting Zones
• Maximum current not exceeding 20A, 12V

Pairing with SoundExtreme Product: To pair the LED Rocker Switch Remote Control with a SoundExtreme product, follow these steps:

1. Ensure both the Switch and the SoundExtreme product are powered on.
2. Press and hold the pairing button on the Switch until the LED indicator blinks rapidly.
3. On the SoundExtreme product, initiate the pairing mode according to its user manual.
4. Once paired successfully, the LED Remote Control will be ready to operate the connected product.

Operating the Switch:
The Switch layout consists of various buttons for different functions:

• Power Button: Turns the Switch on or off.
• All Zones Button: Controls all connected LED zones simultaneously.
• Mode Button: Switch between different LED lighting modes.
• Brightness Button: Adjust the brightness level of the LEDs.
• Speed Button: Adjust the speed of lighting effects.
• Scenes Button: Access pre-programmed scenes or presets.

Connecting Power and Wires:

When connecting power and wires to the Switch, follow these guidelines:

• Connect only to a +12V DC power supply.
• Ensure correct polarity when connecting power inputs and outputs.
• Remote Turn-On Output wire provides a +12V signal when the Switch is on.
• Connect power outputs to the SoundExtreme product’s power input.

FAQ

• Q: How do I reset the pairing between the Switch and a SoundExtreme product?
  A: To reset the pairing, press and hold the pairing button on the Switch for 10 seconds until the LED indicator flashes rapidly, then follow the pairing steps again with your desired product.

User Guide

Important

• Please read this User Guide before installation and use.
• CAUTION: The power input voltage range for your LED Rocker Switch Remote Control (referred to as Switch) is 9V to 16V. It is designed to work with a +12V DC battery power supply. If your vehicle battery power output is not 12V (e.g., 24 V, 36V, or 48V), you will need a voltage converter with 12V output (e.g., a 48V-to-12V converter). Connecting the Switch directly to higher voltages will cause damage to your device and
• VOID THE PRODUCT WARRANTY.
• The Switch has a built-in RF remote transmitter that will operate the LED lights on a wirelessly paired, LEDCast-enabled SoundExtreme product. This Switch only controls LED light functions, not audio. It is optimized for the ExtremeController (a 4-Zone LED Controller by SoundExtreme). To control the audio functions as well as basic LED controls of SoundExtreme soundbars, speakers, and radios, please purchase the Audio Rocker Switch Remote Control. Visit www.soundextreme.us for more details.
• The Switch fits in a standard Carling rocker switch opening, which is commonly used in the dashboard of many off-road vehicles, boats, and golf cars. The Switch panel is waterproof; however, the housing behind the panel is only splash proof.
• CAUTION: In order to make sure there is no potential damage to your audio system, unplug or power off your audio equipment until after all connections are completed.

Features
The Switch is an all-in-one device providing power and wireless LED lighting controls to a paired SoundExtreme product.

Remote Turn-On Output
In addition to operating as a power switch, the Switch also has a +12V Remote Turn-On signal output, which can be connected to an ExtremeController’s Remote Turn-On Input. That ExtremeController can then be automatically turned on or off when you turn the Switch on or off.

RF Remote Transmitter
The Switch has a built-in RF 433MHz remote transmitter, which is used to pair with and control an ExtremeController or other LEDCast-enabled Sound Extreme product. The first time you use the Switch, you will need to pair it with a product. Once they are paired, your product will remember your Switch. Next time you power on your product, your Switch’s remote functions will be ready to use.

Lighting Control Concepts
Below are some terms and definitions to help you better understand the Lighting Control Concepts associated with the ExtremeController and other LEDCast-enabled SoundExtreme products. Please refer to the ExtremeController User Guide for more details.

Zone
A Zone corresponds to all the LED lights that are connected directly to one physical connection on an LED Lighting Controller output. When you change a Zone status (on I off, Mode, etc.), the LEDs connected to that Zone will change accordingly. Depending on the product the Switch is paired with, the SoundExtreme product may have 1 to 4 LED lighting Zones.

Introduction

Mode
There are 3 LED Mode categories, totaling in 44 Modes supported by the Switch’s RF remote control:

• 8ColorMode
• 20 Party Mode
• 16 Music Mode

Scene
A Scene is programed via the Sound Extreme Smartphone App. You can customize each Zone into a Scene (a preset). Setting the Scenes on the app allows a 1-button press to bring up your desired custom settings for all of the LED products connected to the LED Lighting Controller. LEDCast-enabled SoundExtreme products have 5 Scene settings.

Switch Layout

Switch Overview

Connectors
Input

• Power Input: +12V, GND-Connect to your vehicle’s +12V battery.
• Only connect to a+ 12V DC power supply.

Outputs:

• Remote Turn-On Output: +12V signal output when the Switch is on.
• Power Outputs:+ 12V, GND -Connect to a Sound Extreme product’s power input (maximum current not exceeding 20A, 12V).

Button Functions

Power Button
Press and hold for 3 seconds to turn the Switch on or off.
When the Switch is on, short-press to turn the button backlights on or off.
When the Switch is on, double-click to enable RF Remote Pairing with a SoundExtreme product.

Brightness Button

• Short-press to cycle through 5 levels of LED brightness for all of the Zones.

Speed Button

• Short-press to cycle through 5 levels of LED lighting speed for all of the Zones, while in a Party Mode.

All Zones Button ( )

• Short-press to turn all of the Zones on or off.

Mode Button

• Short-press to cycle through all of the LED lighting Modes for all of the Zones.

Scenes Button

• Short-press to cycle through 5 predefined LED lighting Scenes.

Installation and Wiring

Installing Your Switch Onto Your Vehicle
The Switch is designed to snap into a standard Carling style rocker switch opening.

• If you already have that style of an opening on your vehicle, you can simply snap the Switch into place.
• If your vehicle doesn’t already have that style of an opening, you will need to cut a rectangular hole into your vehicle. Before you cut, please refer to the dimensions under the Specifications section to determine the cutout size.

Connecting to an External Speaker
If you want to provide power to and control an external ExtremeController’s or other LEDCast-enabled SoundExtreme product’s power on and off feature, you will need to connect it to the Switch’s Accessory Power Outputs and Remote Turn-On Ouput.

Accessory Power Outputs

Connect the Switch’s Accessory Power Outputs (+12V and GND) to the power inputs on the ExtremeController you want to control.

• Make sure that the Switch’s RED+ 12V Wire is connected to the ExtremeController’s RED Wire and the Switch’s BLACK GND Wire is connected to the ExtremeController’s BLACK Wire.

Remote Turn-On Output

Besides the 12V power supply, the Switch has an optional Remote Turn-On Signal Output to turn on and power off the ExtremeController or LEDCast-enabled SoundExtreme product you want to control. The output voltage is 12V.

If your SoundExreme product has a Remote Turn-On Input. follow the steps below

1. Connect the Switch’s (Dark Blue) Remote Turn-On Output Wire to the ExtremeController·s Remote Turn-On Input. You may need an extension cable (supplied with the ExtremeController).
2. Once the connections are completed, the ExtremeController will automatically turn on or off when the Switch is turned on or off.

Installation and Wiring

Connecting to 12VDC Power Supply
When you install the Switch to a battery or a voltage regulator on a golf cart, a boat, a quad bike, a UTV, or another vehicle, you need to make sure that your vehicle battery or battery pack terminal voltage is 12VDC. If the battery terminal voltage is not 12V, you will need a DC-DC converter with output 12V. Connecting the Switch to a non-12VDC power source will lead to a malfunction or damage to the Switch.

Recommendation : If you are not familiar with all of the vehicle’s battery or ignition switch connections, consult your vehicle’s manual or a technician. Incorrect connections to your vehicle’s battery or ignition signal terminal may cause damage to your speaker and your vehicle.

Connect the +12Vand GND wires to the 12VDC power supply.

• Make sure that the RED Wire is connected to + 12V battery’s positive ( +) terminal and the BLACK Wire is connected to battery’s negative(-) terminal.

WARNING! Only connect to a 12V power supply. Do NOT connect to a 24 V, 36V, or 48V power supply. Connecting the Switch directly to these higher voltages will cause damage to the Switch and VOID THE PRODUCT WARRANTY.

First Time RF Remote Pairing

The first time you use the Switch, you will need to pair the Switch with an ExtremeController or other LEDCast-enabled SoundExtreme product. This process is only needed for the first time you use the Switch with a product.

Please follow the steps below for first-time pairing:

1. Press and hold the Power Button to turn the Switch on.

2.  If you are pairing with an ExtremeController, the ExtremeController will automatically enable remote pairing when turned on. If you are pairing with another SoundExtreme product, you may need to enable RF remote pairing on your Sound Extreme product.
   Example: On a Sound Extreme Elite Sound bar, press and hold both the Buttons on the Sound bar at the same time for 3 seconds. The Soundbar’s LED Party Lights will flash Green, indicating it is ready to pair with a remote.

3. On your Switch, double-click the Power Button . Your Switch will start pairing.

4. Once paired, the LED Party Lights connected to the ExtremeController will rapidly flash Green 3 times, indicating a successful pairing.
   Note: The paired product may produce a different prompt to indicate a successful pairing. Please refer to the product’s User Guide.

5. Now you can press a button on the Switch, such as the All Zones Button, to check if your ExtremeController responds.

Specifications

Dimensions

• Unit Weight
  4.59 oz (130 g)

• Power Input
  9-16V,20A

• Power Output
  9-16V,20A

• Remote Turn-On Output
  12V, 1.2mA

• Storage Temperature
  -40° F to 122° F / -40°C to 50°C

• Operating Temperature
  23° F to 95° F / -5°C to 35°C

FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator to your body.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC STATEMENT:
This device complies with Industry Canada license-exempt ASS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference. including interference that may cause undesired operation of the device.

PRODUCT USE AND PROTECTION
Read and follow all instructions. Use only as intended
The Sound Extreme unit is intended to be used indoors or outdoors and in land or water environments. The unit has been tested to IP66 waterproofing standards, which means the unit can be exposed to dust and water. but should NOT be submerged underwater.
To prevent fire or shock, do NOT attempt to power this unit if rt is wet or you suspect water has entered the unit. In this situation, please return the unit to SoundExtreme for a free assessment. If we have found that the unit has carried water, we will repair or replace the unit free of charge.

SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended.

• CAUTION: Do NOT open to repair. A qualified technician must carry out repair work.
• ATTENTION: Do NOT connect to a Sound Extreme product with LEDCast technology while the unit is wet. Make sure all connections are dry BEFORE connecting to a power source. Failure to do so may result in electrical damage to the unit and may void the warranty.
• WARNING: Cancer and Reproductive Harm-www.P65Warnings.ca.gov
• ATTENTION: Do NOT dispose of in a landfill. Contact SoundExtreme at www.gracesupport.com or a certified recycling agent to dispose of the unit.

SAFETY
This product has a limited life span of use and should be replaced when it shows obvious signs of wear.
Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit. allowing water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your SoundExtreme unit. You should always

1. Return the unit to Sound Extreme if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the Integrity of the unit to take on water.

You should never

1. Never power your SoundExtreme unit if you suspect water has entered the device. Powering a device with water inside could be potentially hazardous and cause fire or a spark.
2. Never use your SoundExtreme unit If you have dropped it or thrown It against a hard surface which may have destroyed the integrity of the housing. In the event of a severe impact to your unit. please return the unit to Sound Extreme to review for potential damage.
3. Never attempt to fix. repair your Sound Extreme unit Please send ii back to SoundExtreme for any assessments and repairs.

CARE, MAINTENANCE & PRECAUTIONS

1. Do NOT apply excessive force to any surfaces of the unit.
2. Do NOT use or store the unit in places with high temperature.
3. AVOID prolonged exposure to ultraviolet radiation (UV sunlight) arid strong magnetic fields.

LIMITED MANUFACTURER’S WARRANTY:
The Switch is covered by a 1-year limited warranty that covers defects in workmanship arid/ or materials for
a period of 1 year from original purchase date. This warranty does not apply to any products which have been abused. neglected, modified or used for a purpose other than the one for which they were manufactured Please refer to the above care and maintenance instructions for suggested care details. The warranty is valid only for the original owner who purchases the unit from an authorized dealer. Transfers do not qualify for warranty protection. Sound Extreme reserves the right to replace any out-of-stock or discontinued product with a comparable product. DiscontJnued products may not be available for warranty replacement. Any contents are NOT covered by the limited manufacturer’s warranty. Warranty terms may be revised without notification at the discretion of the manufacturer Please visit www.soundextreme us for additional product & warranty information.

LED Rocker Switch Remote Control by SoundExtreme Inc., Houston, Texas. DeSIQned In Texas Made in China

What’s in the Box

SOUND EXTREME BY ECOXGEAR

References

• P65Warnings.ca.gov
• SoundExtreme

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>