Lanxi Wheel Top Cycle Industries EDSOX Electronic Derailleur System User Manual

SAFETY INSTRUCTIONS

Read and understand this manual before proceeding with installation. Improperly install extreme danger and could result in severe or fatal injuries. If you have any questions about the installation of these components, consult a qualified bicycle mechanic.

NOTICE

This manual is a complete system installation guide, from unboxing each component till heading out for a ride. Complete the installation and setup in described order in the manual. Do not begin a new step without completing current step.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.

TOOLS AND SUPPLIES

It requires very professional tools and articles. Our suggestion is through a professional bicycle mechanic installation.

CONTROLLER

A. Push Buttons
B. LED Indicator
C. Clamp
D. Plug Screw
E. Dip switch (pairing/mode switching)
F. Battery Cover

REAR DERAILLEUR

A. Battery Latch
B. Mounting Bolt
C. High Limit Screw
D. Low Limit Screw
E. LED Indicator
F. Guide rolle
G. Battery
H. Adjust Screw

BATTERY CHARGING

Charging operation

1. Push in the Battery
2. Start charging Remove battery after
3. Remove battery after

LED Indicator Description

A. Blue: waiting for battery access
B. Red: charging
C. Green: Charged

Precautions

1. Please confirm that the DC connector with USB port with 5.0Vdc voltage and a current ≥ 1.0Adc.
2. If LED light doesn’t show green after 6 hours charging, please stop charging and remove battery.
3. Make sure your hands or gloves are dry when operating this

BATTERY INSTALLATION

Installation instructions

1. Open the battery latch
2. Remove cover
3. Insert the battery into the transmission
4. Close the battery buckle

Precautions

1. Only proper installation of battery could latch be tightly closed.
2. Replace the battery repeat the operation described in the installation instructions
3. Do not disassemble by force, which could easily damage the battery or transmission.

SYSTEM PAIRING

Pairing operation

1. Push the battery onto rear dial shell. At this time, the rear dial indicator light should show blue.
2. Open battery cover B according to the arrow direction. Remove battery C. Turn the dial code E from “N” to “T”. Install the battery C into the dial and close the battery cover B. At this time, the dial indicator light D showing blue flashes meaning pairing.
3. Wait for 5-15 seconds. When the flashing light goes out, it means pairing finished.
4. Dial E from “T” to “N”.
5. If you can shift the rear dial by pressing the dial button, it means installation complete. Otherwise, repeat steps 1 to 4

Precautions

1. The derailleur has been paired before unpacking, and new pairing is not required.
2. The battery does not need to be removed when dialing the controller.
3. In case of wrong operation during pairing, the pairing operation shall be repeated.
4. Every time the rear derailleur detects the battery, the LED indicator will flash blue, and it will enter the allocated state. If the battery is matched, it can be controlled directly with the dial.
5. New paring is not needed in case of battery replacement (rear dial / controller).
6. If any parts are replaced, added or removed(, the pairing process must be repeated.

SHIFTING

Operate the shift button to move the transmission inwards and close to the large tooth plate. Long press to complete multiple speed changes.

Each time the dial lever is toggled, the finger LED will flash, and the finger LED will flash continuously when the dial lever is continuously toggled.

Operate the shift button so that the transmission moves outwards and close to the small tooth plate. Long press to complete multiple speed changes.

Each time the dial lever is toggled, the finger LED will flash, and the finger LED will flash continuously when the dial lever is continuously toggled.

Rear Derailleur installation

Use a 5mm Allen wrench to mount the Rear Derailleur to the frame hook, and use a suitable chain to alternately pass through the two guide wheels of the transmission.

Precautions

1. Mounting bolt locking torque 8.0-10N.M.
2. If the tightening operation is not correct, it may lead to the following phenomena: deformation of hook hole, and installation or disassemble cannot be carried out. Poor shifting performance.
3. Do not apply grease to the installation bolts or hook threaded holes.
4. Incorrect chain selection will reduce the reliability of shifting, which may lead to failure in serious cases.
5. Transmission compatible with 10-52T freewheel.
6. The transmission performance is best when the distance between the freewheel locking cover and the inner plane of rear lower fork is 5mm.

CONTROLLER INSTALLATION

Use a 4rnm Allen wrench to install the transmission on the handlebar, rotate to the appropriate position, and tighten the lock nut

Precautions

1. Mounting bolt locking torque 2.0-5.0N.M
2. Do not apply grease to the mounting bolts or inner side of the lock rings

DERAILLEUR ADJUSTMENTS

Fine Tuning

1. Dial the dial code B from “N” to “T”, and press the dial button, and the blue indicator will flash once every time you press it.
2. to align the center a of the guide wheel of the rear derailleur “A” and the center of the minimum toothed disc; turn the dial code from “T” to “N” to exit the fine tuning mode.

Adjust the derailleur

1. Turn the finger lever until the center of the rear derailleur guide wheel is aligned with the center of the maximum gear, and adjust the adjusting screw until the distance between the guide wheel and the maximum gear is 4-10 mm. (Different rear sprocket sizes will be different, and the optimal distance will be different. The size here is only for reference)
2. Adjust the high limit screw until it lightly touches the inner joint, then turn the bolt for 1\4 turns.
3. Turn the finger lever until the center of the rear derailleur guide wheel is aligned with the center of the minimum gear, adjust the bottom limit screw until it lightly touches the inner joint, and then turn the bolt 1\4 turns.

Precautions

1. The Fine Tuning function can finely adjust the axial distance between the transmission and the sprocket (0.2mm each time), which can optimize the performance of the transmission and improve the smoothness of gear shifting.
2. When adjusting the transmission, be sure to rotate the sprocket, otherwise it may damage the transmission.
3. In the fine tuning mode, press the finger lever continuously, derailleur will move continuously and quickly, ignoring the gear.
4. The transmission will return to the previous position when encountering the force hindering the shift during gear shifting or Fine-Tuning.

OVERVIEW OF INDICATOR LIGHTS

Controller

Green: Normal Shifting Mode
Blue: Fine Tuning Mode\ Pairing Mode
Red: Battery power is less than 5%

Rear Derailleur

Battery check: flashing 1-4 times indicates the battery capacity (power on each time)
Pairing mode: indicator light flashes continuously
Firmware upgrade: the indicator light is always on.

Charger

Green: Charged
Blue: Waiting for battery access
Red: Charging

MAINTENANCE

Controller Battery

Use coins to rotate the battery cover counterclockwise, remove the battery, insert the new CR2032 battery into the negative electrode first, and rotate the battery cover clockwise.

Spare parts replacement

If the rear derailleur or the finger is damaged separately, please refer to “Controller installation” or the “derailleur installations” when replacing it. Replacement of any accessory requires a new pairing.

Precautions

1. Only CR2032 can be used for the finger battery
2. It is recommended to clean the derailleur regularly.
3. The operating temperature of the derailleur is-10° -50°
4. The derailleur is not used for a long time. It is recommended to remove the battery and install the derailleur protection cover.
5. The derailleur battery can only use special battery

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>