CORSA Performance 47002 Closed Box Air Intake Installation Guide

June 13, 2024
CORSA PERFORMANCE

2021+ FORD BRONCO 2.3L
Closed Box Air Intake
Part #: 47002, 470026, 47002D

CORSA Performance 47002 Closed Box Air Intake - Cover

IMPORTANT! WARRANTY AND
INSTALLATION INSTRUCTIONS Please Forward All Information to Consumer

47002 Closed Box Air Intake

Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions about the enclosed parts or instructions, or if you encounter a problem during installation:
CALL TECHNICAL SUPPORT: 440.891.0999 or 800.486.0999
TO ACTIVATE YOUR WARRANTY GO TO: CORSAPERFORMANCE.COM/WARRANTY
COLOR INSTRUCTIONS ARE AVAILABLE BY PART NUMBER ON: CORSAPERFORMANCE.COM


NEVER work on a hot engine bay.
Allow time for the vehicle to cool.
INSTALL DIFFICULTY

RECOMMENDED TOOLS & SUPPLIES

  • ¼” Drive Ratchet
  • 7mm Socket
  • 8mm Socket
  • 10mm Socket
  • 10mm Wrench
  • Trim Removal Tool or Similar
  • Phillips Screwdriver

Please take time to read and understand these installation instructions.
CORSA recommends that the installation of this system be performed by a qualified service center or professional installer who has the necessary equipment, tools, and experienced personnel. However, if you decide to perform this installation yourself, the use of an additional person may be required.

WARNING: Never work on a hot engine bay. Allow time for the vehicle to cool.
Check that this air intake complies with your Federal, State, and Local laws. We recommend saving your stock system.
This warranty does not extend to damaged or defect in the finish of a product or to any product, that in the opinion of CORSA Performance, has been misused, damaged by accident or negligence, altered or modified in any way, faulty installation or installed contrary to CORSA installation instructions, or repaired by an unauthorized service facility.
Full warranty available on www.corsaperformance.com

Please confirm that all parts are present according to the bill of materials before beginning the installation.
If something is missing call Tech Support at 440.891.099 or Toll Free: 1.800.486.0999

CORSA Performance 47002 Closed Box Air Intake - Product Overview
1

PREASSEMBLED MATERIALS

1. 412236 – Closed Air Box| 1| 2. 441325 – Air Duct| 1| 3. 5143 (shown) or 61509 – Air Filter| 1
---|---|---|---|---|---

HARDWARE KIT

4. 52056 – Ø3.5” Clamp| 1| 5. 53308 – Ø3.5” x Ø3.25” Silicone
Reducer| 1| 6. 52048 – Ø3.25” Clamp| 1
---|---|---|---|---|---
7. 56001 – Bulb Seal Trim| 14.5″| 8. 652235 – Bracket| 1| 9. 5900 – Lid Screw| 5
10. 59012212 – M6x1 Bolt| 1| 11. 59020104 – Washer| 1| 12. 59025122 – Rubber Washer| 5
13. 59034138 – 5/8” Fitting| 1| 14. 59045101 – Rubber Grommet| 1| 15. 652192 – CORSA Lid| 1
16. 652236 – Christmas Tree Clip| 1| 17. 652217 – M6x1 Flange Nut| 1| 18. (NOT PICTURED) 51914P/51920P Pre-Filter| 1

REMOVAL INSTRUCTIONS

FACTORY INTAKE

Locate the vehicle’s battery and disconnect the negative battery cable.
This may reset the computer and clear old air flow data to help prevent CEL errors.

  1. Disconnect the electrical connection on the air temperature sensor by pressing on the tab and pulling.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
1

  2. Remove the PCV line by pressing the green tabs on the fitting up and out then pulling the fitting off.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
2

  3. Use a 10mm socket and rachet to remove the bolt located behind the stock air box. Save bolt for installation step 12.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
3

  4. Use a trim removal tool or similar to unclip the Christmas tree clip on the right of the airbox.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
4

  5. Use a trim removal tool or similar to remove the clip at the front of the air scoop.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
5

  6. Loosen the clamp securing the air duct to stock turbo inlet pipe using and pull the duct off the inlet pipe.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
6

  7. Carefully remove the stock air intake by pulling up and out.
    CORSA Performance 47002 Closed Box Air Intake - REMOVAL INSTRUCTIONS
7

  8. Carefully remove the temperature sensor from the stock air intake by rotating counterclockwise and pulling out. Save temperature sensor for installation step 4.

This concludes the removal of the factory intake.

INSTALLATION INSTRUCTIONS

CORSA INTAKE

  1. Install filter bulb seal trim onto the CORSA air box.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
1

  2. Install the rubber grommet and thread the fitting onto the CORSA air duct.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
2

  3. Install the silicone reducer to the smaller end of the CORSA air duct. Prep the Ø3.5” and Ø3.25” clamps for install by sliding them over the silicone reducer. Use an 8mm socket and ratchet to tighten the Ø3.5” clamp over the duct. Leave the Ø3.25” clamp loose for installation.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
3

  4. Remove the O-ring from the temperature sensor.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
4

  5. Install the temperature sensor to the air duct by fitting it through the rubber grommet. Make sure sensor is oriented as shown.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
5

  6. Fit the air duct through the trim and into the air box.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
6

  7. Install the air filter and air filter clamp directly over the end of the air duct inside the air box. Use an 8mm Socket to tighten. Fit pre-filter over top of filter if desired.

  8. Install the bracket to the drilled hole on the back of the CORSA air box using the supplied bolt, nut, and washer. Use a 10mm socket ratchet and wrench to tighten.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
8

  9. Carefully install CORSA air intake and fit the silicone reducer over the stock turbo inlet pipe. Tighten Ø3.25” clamp reconnect the PCV line to the Volant air duct by pressing it over the fitting until it clicks into place.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
9

  10. Re-attach electrical connection to the temperature sensor by pressing until it clicks into place.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
10

  11. Align the supplied bracket to the threaded hole in the frame and use a 10mm socket and the stock bolt from removal step 3 to secure the CORSA airbox to the vehicle.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
11

  12. Use the supplied Christmas Tree clip to secure the scoop portion of the CORSA airbox to the stock air intake tray.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
12

  13. Place the CORSA lid on top of the airbox and tighten to the air box using the lid screws and a Phillips screwdriver.
    CORSA Performance 47002 Closed Box Air Intake - INSTALLATION INSTRUCTIONS
13

This concludes the installation of your CORSA air intake system.

Check that this air intake complies with your Federal, State and Local laws.
We recommend saving your stock system.

BEFORE ROAD TESTING

  1. Start engine, leaving the transmission in park and securing the parking brake.
  2. Make sure to look and listen for any unusual noises or air leaks. Repair problems if needed.
  3. Once completed it will be necessary to check periodically, after a few heat cycles, for realignment and tightening of all connections.

Max Flow 5 CARE AND CLEANING
Check the Max Flow 5 cotton reusable filter periodically and remove any excessive dirt build-up by tapping the filter on the ground and brushing off the loosened dirt. Clean the filter by using a two stage cleaning kit to thoroughly clean and re-oil the filter. Re-oil every 10,000 miles without cleaning to improve filtering in sand and dirt. Clean only when dirt is very excessive or 50,000 miles.

Reference for Replacement Filters: Max Flow 5 Filter Part #5143, DryTech 3D Filter Part #5143D, or PowerCore Filter 61509.
INS47002
140 Blaze Industrial Parkway, Berea, OH 44017 l P: 440.891.0999 F: 440.891.1868
techsupport@tmgperformance.com
www.corsaperformance.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals