SOUNDEXTREME SEI-ETBAT7708 8 Inch Tower Speakers Installation Guide

June 12, 2024
SoundExtreme

SEI-ETBAT7708 8 Inch Tower Speakers

Product Information:

  • Product Name: ExtremeTower TB8

  • Models: SEI-ETBAT7700…20

  • Type: Tower Speakers

  • Size: 8 inches

  • Components: 1 Bluetooth Amplified Tower Speaker, 1 Passive
    Tower Speaker

  • Features: Built-in amplifier, LEDCast LED controller for
    controlling LED Party Lights on both speakers

Product Usage Instructions:

  1. Before unboxing, read the Hardware Guide, the ExtremeTower
    Speakers Installation Guide, and the User Guide.

  2. The ExtremeTower TB8 set includes two types of speakers: one
    passive speaker and one amplified speaker with a built-in amplifier
    and LEDCast LED controller.

  3. Important: Do not connect this product to any other
    manufacturers’ LED controller to avoid permanent damage and voiding
    the product warranty.

  4. Choose the power connection option for the Amplified Tower
    Speaker:

    • Connect to your vehicle’s battery
    • Use a removable and rechargeable Battery Pack (can be charged
      via the charger or your vehicle’s battery/power)
  5. The speaker’s battery will only be charged by the vehicle when
    the vehicle is switched and powered on. It will not drain power
    from the vehicle’s battery when the vehicle is switched off.

  6. There are two power and signal connection jacks on the
    speakers:

    • A round Aviation Connector Jack inside the speaker’s
      Base-Mount

    • A square Deutsch Connector Jack behind the speaker’s
      Base-Mount, covered by a rubber cap

  7. Two cable sets are included:

    • Aviation Cable Set (Round Connector) – used for speaker
      installation where the cable needs to pass through the Bottom Mount
      Clamp and go into a hole in the crossbar at the spot where the
      speaker is mounted.

    • Deutsch Cable Set (Square Connector) – if using this set,
      ensure the rubber cap is screwed into the connector jack on the
      speaker using a long nose plier or similar tool to prevent water or
      moisture penetration and potential damage to the speaker.

  8. Only use one set of cables (Aviation or Deutsch) at a time. Do
    not wire the speakers with both the Aviation Cables and Deutsch
    Cables simultaneously.

PLEASE READ
BEFORE UNBOXING
BEFORE you start unpacking your ExtremeTower Speakers, PLEASE READ this Hardware Guide, then read the ExtremeTower Speakers Installation and User Guides.

ExtremeTower TB8 | Models: SEI-ETBAT7700…20
8 inch Tower Speakers
Hardware Guide

1 Bluetooth Amplified Tower Speaker

1 1 Battery +

Passive Tower Speaker

Hardware Guide
ExtremeTower Packaging Layout
Mounting parts and tools are in the top level and the cables are located in the bottom level of the protective foam packaging. Top Level: Mounting Parts and Tools

1

2

5

3 4
67

1. Remote Control (1 pc) 2. Clamps · Clamps – Top & Bottom (2 sets) 3. Locking Harness Sets · Locking Screw Latches (2 pcs) · Quick Release Knobs (2 pcs) · U-Shaped Pins (2 pcs) · Base Cover Plates (2 pcs) · M3 x 10 Screws (8 pcs) 2

4. Thick Rubber Insert & Bolt Sets
· Thick Rubber Inserts (2 pcs) · Short Mounting Bolts (4 pcs) · Anti-Loose Spring
Washers (4 pcs) · Flat Washers (4 pcs) 5. Battery Pack Set · Battery Pack (1 pc) · Battery Wall Charger (1 pc)

Hardware Guide

6. Mounting Tools · Allen Wrench (1 pc) · Electrical Tape (1 pc) · Heat- Shrink Tubing (6 pcs) · Insulated BUTT Connectors –
Blue (3 pcs) & Red (6 pcs) · 4-Pin Deutsch Rubber Plug (1 pc)

7. Thin Rubber Insert & Bolt Sets
· Thin Rubber Inserts (2 pcs)
· Long Mounting Bolts (4 pcs)
· Anti-Loose Spring Washers (4 pcs)
· Flat Washers (4 pcs)

Bottom Level: Speakers and Cables

1 2

1. Speakers

2. Cable Sets

· ExtremeTower Speakers (2 pcs) · Aviation Cable Sets (2 pcs)

· Aviation Connector Caps (2 pcs) · Deutsch Cable Sets (2 pcs)

· Power Extension Cable (1 pc)

· Remote Turn-On Extension Cable (1 pc) 3

Hardware Guide
The ExtremeTower TB8 Set includes two different types of speakers: 1. One Passive Speaker. 2. One Amplified Speaker with built-in amplifier and LEDCast
LED controller, which powers and controls the LED Party Lights on both speakers. Important: Do NOT connect this product to any other manufacturers’ LED controller. Connecting this product to any other manufacturer’s product may cause permanent damage to the product and shall VOID THE PRODUCT WARRANTY. BEFORE you start your installations please READ the following options for power connections, wiring, and mounting.
Amplified Tower Speaker Power Connection Options
There are two power options for the Amplified Tower Speaker: 1. Connect to your vehicle’s battery. 2. Use a removable and rechargeable Battery
Pack. The Battery Pack can be removed from the speaker and charged via the Charger or left installed in the speaker and be charged by your vehicle’s battery / power. The speaker’s battery will only be charged by the vehicle when your vehicle is switched and powered on. When your vehicle is switched off, the speaker will only use the battery charge of the integrated battery and will NOT drain power from your vehicle’s battery.
4

Hardware Guide

Speaker Power and Signal Wiring Cable Options
There are two power and signal connection jacks on the speakers:

Deutsch Connector Jack

Aviation Connector Jack

1. A round Aviation Connector Jack is inside the speaker’s Base-Mount.
2. A square Deutsch Connector Jack is behind the speaker’s Base-Mount, behind a rubber cap.
· The Amplified ExtremeTower Speaker has two Deutsch Connector Jacks.
Your speakers include two Cable sets.
IMPORTANT
1. An Aviation Connector Jack Cover Cap is attached to the Base-Mount on the speaker.
If you choose to use the Deutsch Cable Set for wiring, before installation, you MUST screw the cap into the connector jack on the speaker, tightening it clockwise with a long nose plier (not included) or similar tool. Failing to do this will result in potential water or moisture penetration into the jack connector pins, causing damage to the speaker and VOIDING THE PRODUCT WARRANTY.
5

Hardware Guide
2. Only ONE set of cables (Aviation or Deutsch) can be used at a time. Do NOT wire the speakers with BOTH the Aviation Cables and Deutsch Cables.
Aviation Cable (Round Connector)

Deutsch Cable (Square Connector)

CABLE SET
Aviation Cable Set (Round Connector)
Deutsch Cable Set (Square Connector)

CABLE USE
This cable set is used for the speaker
installation which requires the cable to pass through the Bottom Mount Clamp and go into a hole in the crossbar at the spot where the speaker is mounted.
This cable set is used for the speaker
installation which does NOT require the cable to pass the Bottom Mount Clamp and go into a hole in the crossbar at the spot where the speaker is mounted.

SET INCLUDES
· “Round A1” 9-Pin to 6-Pin Pass-Through LED and Speaker Aviation Cable.
· “Round A2” 6-Pin Pass-Through Aviation Cable.
· “Deutsch A1” 4-pin Power Cable.
· “Deutsch A2″ 6-Pin Interconnection Cable.

6

Hardware Guide

Mounting Options
1. Rubber Inserts — The Rubber Inserts are included to allow for best fit on different bar sizes. Your speakers include two Rubber Insert sets:

RUBBER SET
Rubber Insert Set (Thin)
Rubber Insert Set (Thick)

RUBBER USE
Fit 2.5″ to 3.0″ bar size.

SET INCLUDES
· Thin rubber inserts.
· Long mounting bolts, anti-loose spring washers, flat washers.

Fit 1.5″ to 2.5” bar size.

· Thick rubber inserts.
· Short mounting bolts, anti-loose spring washers, flat washers.

2. Locking Harness — The Locking Harness is included to lock both the U-shaped Pin and the Swivel Flange on the Bottom Clamp Assembly. There are two different Locking Screw Latches for you to select from:

· Locking Screw Latch with a Hex Nut ­ It is necessary to use an Allen wrench (included) to tighten or untighten the latch.
7

Hardware Guide
· Locking Screw Latch with a Quick-Release Knob ­ A tool is NOT required to tighten or untighten the latch. This option is more convenient to mount and unmount your speaker for portable use or theft deterrence. It is suggested that you use the rear Deutsch Connection Cable option with the Quick Release Knob as the round Aviation Cable option is difficult to connect and disconnect multiple times.
AFTER you read this Hardware Guide and locate ALL the included accessories packaged in the box, please follow the steps in the ExtremeTower Speakers Installation Guide and User Guide.
8

ExtremeTower
8 inch Tower Speakers
Built-in Amplifier

Installation Guide

ExtremeTower TA8
Models: SEI-ETAMP7700…20

1

Bluetooth Amplified Tower Speaker

1 Passive Tower Speaker

ExtremeTower TB8
Models: SEI-ETBAT7700…20

1

Bluetooth Amplified Tower Speaker

1 Passive Tower Speaker

1 Battery

Important
· Please read the Hardware Guide, this Installation Guide, and the User Guide before installation and use.
· This Installation Guide is for the TA8 (SEI-ETAMP7700…20) and TB8 (SEI- ETBAT7700…20) ExtremeTower Speakers. The TA8 Speakers do NOT include a removable, rechargeable battery. You can purchase the battery separately.
· Only connect a 12V Power Supply to the Amplified Speaker power input. To prevent damage to the speakers, fire, and/or possible injury, do NOT connect the BLACK Power Cable to the battery’s negative (-) terminal until all the installations are completed.
· CAUTION: Do NOT connect to a 24V, 48V or 72V power supply! The voltage for the power input is +12VDC. You need to connect to a 12VDC power supply. If your vehicle battery power is not 12V (e.g., 24V, 36V, or 48V), you will need a DC-DC voltage converter with 12V output (e.g. a 48V-to-12V converter). Connecting the ExtremeTower directly to higher voltages will cause damage to the speaker and cause the rechargeable battery to overcharge and overheat! In extreme cases, excess voltage can cause the battery to expand, leak, or potentially catch on FIRE! Any damage to the battery due to improper connections to higher voltages will VOID THE PRODUCT WARRANTY.
· The Amplified Speaker has a Remote Turn-On Input feature; this is to ensure that the speaker is completely powered off (no battery consumption) when your vehicle is not in use. When the Remote Turn-On Input has a 12V signal, the speaker will turn on or go into standby, depending on the Power Mode Switch settings. When there is no input voltage, the speaker will turn off. In general, this Remote Turn-On signal comes from the vehicle ignition switch ­ make sure that the signal voltage on the ignition switch is 12V. If your vehicle ignition switch signal is not 12V or if you are not able to get a connection to the ignition switch, you can connect the Remote Turn-On Wire on the Amplified Speaker to a rocker switch. Then connect the rocker switch to a 12V power supply or the 12V output on your voltage convertor. Additionally, some vehicles have a built-in 12V switch panel, which will also work for the Remote Turn-On Wire.
2

Important
· When mounting the speaker, it is extremely important to make sure that the mount is secure and will not cause any potential issues. Please check that the speaker does NOT block the driver’s view or prevents the safe operation of your boat or other vehicle. Ensure that all screws are tightened and the speaker is secured correctly so that the speaker will NOT fall.
· It is highly recommended to periodically check that the mount is secured. If loose, please retighten the Locking Screw Latch.
RECOMMENDATION: Do NOT install on your own. This installation is a two-person job, to be done safely. Please be careful to ensure no personal injury or damage to your vehicle.
· An Aviation Connector Jack Cap comes attached to the Base-Mount on each speaker. If you choose to use the Deutsch Cable Set for wiring, you MUST screw the cap into the unused Aviation Connector Jack on each speaker, tightening it clockwise with a long nose plier (not included) or similar tool. Failing to do this may result in potential water or moisture penetration into the jack connector pins, cause damage to the speaker, and VOID THE PRODUCT WARRANTY.
· When you connect the 9-pin or 6-pin Aviation Connector to the Aviation Connector Jack in the Base-Mount, you MUST ensure the connector is tightened (clockwise) so that the connection is waterproof.
· When using the Extension Cable and/or connecting two wires (e.g., using supplied BUTT Connectors), make sure to seal the connection either by using electrical tape or heat shrink tubing. Failing to do this may result in long- term corrosion on the connection and cause a premature malfunction.
CAUTION: After taking the product out of the polyethylene bag, be sure to dispose of the polyethylene bag out of the reach of children. Children may play with the bag, which could result in the child’s suffocation.
3

ExtremeTower Overview
ExtremeTower Passive Speaker Layout
Tweeter

Party Lights Speaker

U-Shaped Pin

Quick-Release Knob

Rotating 360° Mount Clamp

Base-Mount

Top Mount Clamp Bottom Mount Clamp

4

ExtremeTower Overview
ExtremeTower Amplified Speaker Layout

Battery Pack Switches
Control Buttons

Waterproof Back Cover

Back Cover Latch Release Button

Dome Light 5

ExtremeTower Overview
Audio, LED Control Signals, and Power Connectors and Cables
Amplified Tower Speaker and Passive Tower Speaker
· Your package has one Amplified Tower Speaker and one Passive Tower Speaker.
· The Passive Tower Speaker must be connected to the Amplified Tower Speaker to receive audio and LED control signals.
Power, Audio, and LED Lighting Connections
Power + 12V DC Ground Remote Turn-On Speaker Detect LED Power LED Ground Speaker Speaker + LED Signal
The Amplified ExtremeTower Speaker has 9 input and output wires.
· 3 Input Wires: 12V (+), GND (-), and Remote Turn-On to connect to your vehicle.
· 6 Wires: To connect both speakers together.
Speaker Detect LED Power LED Ground Speaker Speaker + LED Signal
The Passive ExtremeTower Speaker only has 6 input wires.
6

ExtremeTower Overview

Speaker Connector Jacks Each speaker has 2 types of Connector Jacks.

6-Pin Aviation Connector Jack

9-Pin Aviation Connector Jack

6-Pin Deutsch Connector Jack 4-Pin Deutsch Connector Jack
6-Pin Deutsch Connector Jack
1. A round Aviation Connector Jack is inside the speaker Base-Mount, which allows the cable to pass through the Bottom Mount Clamp and go into a hole in the crossbar at the location where the speaker is mounted. The Amplified Tower Speaker has a 9-pin, round connector jack, and the Passive Tower Speaker has a 6-pin, round connector jack.
2. A square Deutsch Connector Jack is behind the speaker Base-Mount underneath a rubber cap. This is for an installation where the wire is installed outside of the tower / roll cage.
7

ExtremeTower Overview
This is also the connection suggested if you want to utilize the Quick- Release-Mount option. The Amplified Tower Speaker has both a 4-pin and a 6-pin, square connector jack. The Passive Tower Speaker only has a 6-pin square connector jack. FM Dipole Antenna Jack
FM Dipole Antenna Jack
The Amplified Speaker has a built-in FM Antenna. It also includes an FM Dipole Antenna Jack for an optional external antenna connection and improved reception (dipole antenna sold separately). If you prefer to use an external FM antenna, follow these steps: 1. Slowly pull out the rubber cap. Keep the rubber cap attached to
the speaker housing if you plan to remove the antenna periodically; otherwise, you can remove the antenna cap. 2. Plug your dipole antenna into the FM Dipole Antenna Jack.
8

ExtremeTower Overview

INT EXT
3. Open the Back Cover (refer to Install the Rechargeable Battery Pack to the Amplified Speaker for details), move the (Blue) FM ANT Switch to the EXT position.
Cables
Your package includes 2 Cable Sets for each wiring option.
1. Aviation Cable Set — For easy running and fishing wires through a crossbar. The Aviation Cable connection between the Amplified Tower Speaker and the Passive Tower Speaker uses the following two cables:

3 Bare Wires (Input) 6 Bullet Connectors (Output)

9-Pin Aviation Connector

“Round A1” 9-Pin to 6-Pin Pass-Through LED and Speaker Aviation Cable
· The long cable (“Round A1” 9-pin to 6-pin pass-through Aviation Cable) has a 9-pin round connector on one end and 3 bare wires for power inputs and 6 Bullet connectors on the other end for interconnection with the Passive Tower Speaker.
9

ExtremeTower Overview

6-Pin Aviation Connector

6 Bullet Connectors (Input)

“Round A2” 6-Pin Pass-Through LED and Speaker Aviation Cable

· The short cable (“Round A2” 6-pin pass-through Aviation Cable) has a 6-pin round connector on one end and 6 bullet connectors on the other end.
Note: Besides the Power +12V, GND, and Remote Turn-On connections to your vehicle’s battery and ignition switch, you will need to connect the 6 bullet connectors from both the long and short cables and seal the connections to prevent water or moisture penetration.
2. Deutsch Cable Set –Suggested wiring method if you want to utilize the Quick-Release-Mount option. The Deutsch Cable connection between the Amplified Tower Speaker and the Passive Tower Speaker uses the following two cables:

4-Pin Deutsch Connector

Power Inputs: 12V (+), GND (-), and Remote Turn-On

“Deutsch A1” 4-Pin Power Deutsch Cable
· 4-pin Deutsch connector for 12V (+), GND (-), and Remote Turn-On input for the Amplified Tower Speaker.
10

6-Pin Deutsch Connector

ExtremeTower Overview
6-Pin Deutsch Connector

“Deutsch A2” 6-Pin LED and Speaker Deutsch Cable
· 6-pin Deutsch connector for interconnection between the Amplified Tower Speaker and the Passive Tower Speaker.

11

Installation and Wiring
Installation and Wiring Procedure 1: Round Aviation Cable
If you choose to use the Aviation Cable Set for wiring your ExtremeTower Speakers, follow the steps below. Speaker and LED Lighting Control Wiring The Aviation Cable will pass through the Bottom Mount Clamp and go into a hole in the crossbar; therefore, it is necessary to run the speaker wires and connections before the speakers are mounted onto the crossbar. 1. Find or drill a hole in the crossbar at the spots where the Amplified
Tower Speaker and Passive Tower Speakers will be mounted.
Aviation Connector Jack
2. Fish the “Round A1” (9-pin to 6-pin pass-through) Aviation Cable into the hole in the crossbar where the Amplified Speaker will be mounted and fish the wires through the crossbar to the hole where the Passive Tower Speaker will be mounted.
12

Installation and Wiring
3. Pull out the 9 wires from the hole, make the following wire connections and use heat-shrink tubing or electrical tape to seal the connections:
· Connect the 6 bullet connectors on “Round A1” to those on the “Round A2” (6-pin pass-through) Aviation Cable. Simply match the colors of the cables to each end.
· Connect 3 wires (+12V, GND and Remote Turn-On) with the supplied Power Extension Cable (+12V and GND) and the supplied Remote Turn-On Extension Cable with the supplied BUTT connectors. Use heat-shrink tubing or electrical tape to seal the connections.
4. Fish the 3 wires (+12V, GND and Remote Turn-On) back into the hole and slide them through the crossbar to the vehicle’s battery and ignition signal terminal. But do NOT connect the cables to your vehicle’s 12V battery and ignition signal terminal yet. 13

Installation and Wiring
Mount the Amplified Tower Speaker to the Crossbar 1. Base-Mount: Remove the tape and pull out a small plastic bag from
the Base-Mount. This bag has one Aviation Connector Jack Cap. You don’t need this cap for this installation, but save the cap for later use in case you change the wiring methods.
Rubber Insert Swivel Flange and Bottom Clamp Assembly 4 pcs M3 x 10 Screws Base Cover Plate Aviation Connector
2. Put the appropriate Lower Rubber Insert onto the Swivel Flange and Bottom Clamp Assembly.
3. Fish the “Round A1” (9-pin to 6-pin pass-through) Aviation Cable through the inner hole of the Swivel Flange and Bottom Clamp Assembly, and the Base Cover Plate.
14

Installation and Wiring
4. Connect the (9-pin round) Aviation Connector to the Aviation Connector Jack on the Amplified Speaker. Tighten the connector clockwise with a long nose plier (not included) or similar tool.
IMPORTANT: Tighten the connector to ensure the connection is waterproof to avoid potential water or moisture penetration into the jack connector pins, causing damage to the speaker.
5. Put the Base Cover Plate on the speaker Mount-Base and secure with 4 pcs of M3 x 10 Screws.
6. Insert the Swivel Flange and Bottom Clamp Assembly into the speaker Mount- Base.

ANTENNA

U-Shaped Pin

Locking Screw Latch

7. Insert the U-Shaped Pin into the two holes on the side of the Base-Mount. Insert the pins into the holes on the left side of the Mount when viewing from the rear of the speaker.

8. Attach the Locking Screw Latch onto the U-Shaped Pin ends (make sure Top on the Locking Screw Latch is on top), then move it downward to align the lock catch end with the middle hole of the Base-Mount, and screw in the Locking Screw with the supplied

Locking Screw

15

Installation and Wiring
M5 Allen wrench (or with your hand if utilizing the Quick-Release Knob). Note: It is NOT recommended to use the Quick-Release Knob with this wiring method. Do NOT tighten the screw yet.
Bolts Washers and Spring Washers
Top Clamp
Rubber Insert
9. Put the Upper Rubber Insert on the Top Clamp. Align the rubber groove with the bulge of the Top Clamp and press down to assemble the Clamp and Rubber Insert.
10. Place the Amplified Tower Speaker under the crossbar. Lower the Top Clamp over the crossbar and on the Bottom Clamp. Tighten the two Bolts so that the speaker is securely mounted on the crossbar.
11. Turn the speaker to your desired angle, tighten the Locking Screw with the supplied M5 Allen wrench (or with your hand if utilizing the Quick-Release Knob).
16

Installation and Wiring
Mount the Passive Tower Speaker to the Crossbar
1. Base-Mount: Remove the tape and pull out a small plastic bag from the Base-Mount. This bag has one Aviation Connector Jack Cap. You don’t need this cap for this installation, but save the cap for later use in case you change the wiring methods.
2. Connect the (6-pin round) Aviation Connector to the Connector Jack on the Passive Tower Speaker. Tighten the connector clockwise with a long nose plier (not included) or similar tool.
IMPORTANT: Tighten the connector to ensure the connection is waterproof to avoid potential water or moisture penetration into the jack connector pins, causing damage to the speaker.
3. Repeat Steps 5 through 11 (from Mount the Amplified Tower Speaker to the Crossbar) to mount the Passive Tower Speaker to the Crossbar.
4. Once you complete the installations, proceed to Connecting Your Speaker to a +12V Power Supply and Powering On.
17

Installation and Wiring
Installation and Wiring Procedure 2: Square Deutsch Cable
This cable installation method does NOT require that the cables go through the mount. This method allows for the speakers to be mounted to the crossbar before running the wires and before completing the cable connections.
Pliers (Not Included) Deutsch Connector Jacks
IMPORTANT: Before installation, it is important that you install the Aviation Connector Caps on the Aviation Connector Jacks in the Base-Mounts of both the Amplified Tower Speaker and the Passive Tower Speaker. In the Base-Mount, remove the tape and pull out the Aviation Connector Cap from a small plastic bag. Screw the cap into the Connector Jack on the speaker, tighten it clockwise with a long nose plier (not included) or similar tool. Failing to do this will result in potential water or moisture penetration into the jack connector pins causing damage to the speaker.
18

Installation and Wiring
Mount the Amplified Tower Speaker to the Crossbar
Rubber Insert Swivel Flange and Bottom Clamp Assembly 4 pcs M3 x 10 Screws Base Cover Plate
1. Put the appropriate Lower Rubber Insert onto the Swivel Flange and Bottom Clamp Assembly.
2. Put the Base Cover Plate on the speaker Mount-Base and secure with 4 pcs of M3 x 10 Screws.
3. Insert the Swivel Flange and Bottom Clamp Assembly into the speaker Mount- Base.
19

Installation and Wiring

ANTENNA

U-Shaped Pin

Quick-Release Knob

4. Insert the U-Shaped Pin into the two holes on the side of the Base-Mount. Insert the pins into the holes on the left side of the Mount when viewing from the rear of the speaker.
5. Attach the Quick-Release Knob (or the Locking Screw Latch) onto the U-Shaped Pin ends (make sure Top on the Quick-Release Knob is on top), then move it downward to align the lock catch end with the middle hole of the Base- Mount, and screw in the Locking Screw by turning the Quick-Release Knob (or with the supplied M5 Allen wrench if utilizing the Locking Screw Latch). Do NOT tighten the screw yet.
20

Locking Screw

Bolts Washers and Spring Washers
Top Clamp
Rubber Insert

Installation and Wiring

6. Put the Upper Rubber Insert on the Top Clamp. Align the rubber groove with the bulge of the Top Clamp and press down to assemble the Clamp and Rubber Insert.
7. Place the Tower Speaker under the crossbar. Lower the Top Clamp over the crossbar and on the Bottom Clamp. Tighten the two Bolts so that the speaker is securely mounted on the crossbar.
8. Turn the speaker to your desired angle, tighten the Locking Screw with the supplied M5 Allen wrench (or with your hand if utilizing the Quick-Release Knob).
Mount the Passive Tower Speaker to the Crossbar
1. Repeat Steps 1 through 8 (from Mount the Amplified Tower Speaker to the Crossbar) to mount the Passive Tower Speaker to the Crossbar.
21

Installation and Wiring
2. Remove the 4-pin/6-pin Rubber Plug from the Deutsch Connector Jacks on each speaker and connect the Amplified Tower Speaker and Passive Tower Speaker with the supplied (“Deutsch A2” 6-pin) Deutsch Interconnection Cable. Plug in the Deutsch Connector into the 6-pin Deutsch Jack on each speaker.
3. Run the (“Deutsch A1” 4-pin) Deutsch Power Cable to the location where your vehicle’s power and ignition signal terminal are located, but do NOT connect the cables to your vehicle’s 12V battery and ignition signal terminal yet. Extension Cables have been provided, if needed.
· If needed, connect the 3 wires (+12V, GND, and Remote Turn-On) on the (“Deutsch A1” 4-pin) Deutsch Power Cable with the supplied Power Extension Cable (+12V and GND) and the supplied Remote Turn-On Extension Cable, with the supplied BUTT Connectors. Use heat-shrink tubing or electrical tape to seal the connections.
22

Installation and Wiring
4. Plug in the 4-pin Deutsch Power Cable’s connector into the 4-pin Deutsch Connector Jack on the Amplified Speaker. IMPORTANT: For the TB8 (SEI- ETBAT7700…20) ExtremeTower Speakers, if you do not connect the Amplified Tower Speaker to the vehicle battery, (e.g., “Deutsch A1” 4-pin Power Cable is NOT used) you MUST seal the 4-pin Deutsch Connector Jack by plugging in the included 4-pin Deutsch Rubber Plug, to prevent potential water or moisture penetration into the jack.
5. Once you complete the installation, proceed to Connecting Your Speaker to a +12V Power Supply and Powering On.
23

Installation and Wiring
Connecting Your Speaker to a +12V Power Supply and Powering On

Black Cable Red Cable

Remote Turn-On Extension Cable

1. Once you complete one of the Installation Procedures, you can connect the 3 wires (+12V, GND, and Remote Turn-On) on the Power Cables (or Extension Cables, if needed) to the vehicle’s battery and ignition signal terminal.
· Make sure that the RED Cable is connected to +12V battery’s positive (+) terminal and the BLACK Cable is connected to battery’s negative (-) terminal.
· Alternatively, both the Red Cable and the Remote Turn-On Cable can be connected to a +12V switched power source.
WARNING! Only connect to a 12 volt power supply.
Recommendation: If you are not familiar with all of the vehicle’s battery or ignition switch connections, consult your vehicle’s manual or a technician. Incorrect connections to your vehicle’s battery or ignition signal terminal may cause damage to your speaker and your vehicle.
2. Turn on your vehicle’s ignition switch. Your speakers should turn on. You can now connect an ExtremeTower Speaker to your phone and play your audio or use the built-in FM radio. Refer to your User Guide to learn how to pair two or more Amplified ExtremeTower Speakers, among other features.
24

Installation and Wiring
Install the Rechargeable Battery Pack on the Amplified Speaker
Note: The following instructions are for the TB8 (SEI-ETBAT7700…20) ExtremeTower Speakers.
If your package has a rechargeable battery, follow the steps below to install your Battery Pack on the Amplified Speaker. (The TA8 Speakers do NOT include a removable, rechargeable battery. You can purchase the battery separately.)
IMPORTANT: If you connect the vehicle’s battery and ignition switch signal to the Amplified ExtremeTower Speaker, please turn on the speakers and check if they work fine first, then install the Battery Pack.
1. On the back of the Amplified Speaker, hold the speaker housing, press down the Latch Release Button and rotate the Cover counter-clockwise to unlock the Cover.
2. Pull out the Cover, you will see a blue, rubber Battery Port Cap inside the cavity.
3. Remove the blue Battery Port Cap and plug in the Battery Pack.
Note: Keep the Battery Port Cap for future use. If you do not connect the Amplified Tower Speaker power input to your vehicle power supply, once the battery level is low, you will need to take out this Battery Pack and have the Battery Pack charged by the included wall charger. When you remove the Battery Pack from the back of the speaker, you will need to plug in the
25

Installation and Wiring
Port Cap to protect the Battery Pack’s connection area on the speaker from water, dirt and damage.
4. Place the Cover back on the speaker and turn clockwise until the latch is locked.
IMPORTANT: When you put Cover back, make sure the Cover is closed properly. If not closed properly, the Cover is NOT sealed and water and moisture may penetrate into the battery connection area, causing damage.
Recharge Your Battery Pack
The rechargeable Battery Pack can be charged by either the included Battery Charger or (optionally) by connecting the Amplified Tower Speaker to your vehicle’s power, per the Wiring Procedure instructions. When doing so, your vehicle will only charge the speaker’s Battery Pack when the vehicle ignition is switched on. When your ignition is switched off, it will not charge the Battery Pack; therefore, the Battery Pack will NOT drain your vehicle’s battery.
To release the Battery Pack in order to charge it with the included Battery Charger, simply press the Battery Release Buttons on both sides of the battery and pull it out of the back of the speaker.
26

Next, read your User Guide to explore more features and functions for your
ExtremeTower Speakers
27

28

ExtremeTower
8 inch Tower Speakers

User Guide

ExtremeTower TA8
Models: SEI-ETAMP7700…20

1

Bluetooth Amplified Tower Speaker

1 Passive Tower Speaker

ExtremeTower TB8
Models: SEI-ETBAT7700…20

1

Bluetooth Amplified Tower Speaker

1 Passive Tower Speaker

1 Battery

ExtremeTower TBB8
Models: SEI-ETAMPBAT7700…20
2 Bluetooth Amplified Tower Speakers + 2 Batteries

Important
· Please read the Hardware Guide, Installation Guide, and this User Guide before installation and use.
· If your model includes a rechargeable Battery Pack and you want to use the optional charge feature by connecting to your vehicle’s power source, please confirm you are only providing 12 volts to the speaker BEFORE installing the battery pack.
· CAUTION: Do NOT connect to a 24V, 48V or 72V power supply! The voltage for the power input is +12VDC. Connecting the ExtremeTower directly to higher voltages will cause damage to the speaker and cause the rechargeable battery to overcharge and overheat! In extreme cases, excess voltage can cause the battery to expand, leak, or potentially catch on FIRE! Any damage to the battery due to improper connections to higher voltages will VOID THE PRODUCT WARRANTY.
· The Amplified Speaker has a Remote Turn-On Input Wire. It provides a great feature that ensures there is no power drain when your vehicle is turned off. So, you will need to connect this input with the included Remote Turn-On Wire to your vehicle ignition switch. If you are not able to connect it to your vehicle ignition switch, connect this input to a rocker switch (not included), then connect the rocker switch to your vehicle’s power supply.
· The Amplified ExtremeTower Speaker is compatible with the ECOXGEAR audio and LED lighting EcoSystem, which includes LEDCast and EcoCast Innovations. Look for the LEDCast and EcoCast logos on the growing family of ECOXGEAR and SoundExtreme audio and lighting solutions. EcoCast-enabled audio products are designed to be paired with one or more EcoCast-enabled products. Simply initiate EcoCast Transmitting Mode in one SoundExtreme or ECOXGEAR speaker and broadcast your music to one or more EcoCast-enabled products in Receiving Mode.
· LED lights are known to create interference (noise) on some FM radio frequencies (stations). When you tune or seek a station, it is recommended that you turn the LED Party Lights off.
2

Switches
Power Mode Switch
Power Standby
The Power Mode Switch (Red Switch) is located behind the rear Cover. · Remove the back Cover to view the switch. This switch modifies
the Power On State when you turn on your vehicle ignition switch. · When the Switch is set to the On position (factory default
setting), the speaker will be turned on. · When the Switch is set to the Standby position, the speaker will
enter Standby Mode. You will need to press the Power Button on the Amplified Speaker or the RF Remote Control to turn the speaker on.
FM Antenna Switch
INT EXT
The Amplified Speaker has a built-in FM Antenna. It also includes an FM Dipole Antenna Jack for an optional external antenna connection and improved reception (dipole antenna sold separately). Next to the Power Mode Switch is the FM Antenna Switch (Blue Switch). · When the Switch is set to the INT position (factory default
setting), the speaker will use the internal FM Antenna. · When the Switch is set to the EXT position, the speaker will use
external antenna (sold separately) for FM radio reception. 3

Buttons and LED Status Indicators
Buttons and LED Status Indicators
Only the Amplified Tower Speakers have Control Buttons. The Passive Tower Speakers do not have any Control Buttons and must be controlled via the connected Amplified Speakers. For models with two amplified speakers, the speakers function independently or can be paired wirelessly together via the EcoCast function. Please refer to EcoCast ­ Stream Music Between Multiple Speakers for more details.
1. Power Button · Short-press to turn the speaker on / off. 2. Battery Level LED Indicators · Each LED represents 25% of a charge. 3. Left and Right Channel LED Indicators · L LED Light On: The Amplified Speaker will play the Left Audio
Channel and the passive speaker will play the Right Audio Channel for true stereo. · R LED Light On: The Amplified speaker will play the Left Audio Channel and the passive speaker will play the Right Audio Channel for true stereo. 4

Buttons and LED Status Indicators

· L and R LED Lights On: Both speakers will play the Left and Right Audio Channels (Mono).

4. Mode Button

with LED Indicator

· Short-press to change Modes. The Mode LED Status Indicator will change color to indicate the current Mode:

· Solid Blue: Speaker Mode

· Flashing Red: EcoCast Transmitting ­ Pairing Ready

· Solid Red: EcoCast Transmitting

· Flashing Green: EcoCast Receiving ­ Pairing Ready

· Solid Green: EcoCast Receiving ­ Paired with EcoCast Transmitting speaker

· Flashing Red and White: EcoCast Transmitting in FM Mode ­ Pairing Ready

· Solid White: FM

· PRESS AND HOLD for 2 seconds to enable EcoCast pairing.

5. Bluetooth Button with LED Status Indicator

· Short-press to enable pairing with your phone or other Bluetooth device.

· Flashing Blue: Bluetooth Pairing

· Solid Blue: Bluetooth Connected

· PRESS AND HOLD for 5 seconds to clear all Bluetooth and EcoCast pairing records.

6. FM Preset Buttons

· The speaker has the ability to store and play 3 FM radio presets.

· Short-press a Preset Button and the speaker will tune to the saved station corresponding to the Preset Button.

5

Buttons and LED Status Indicators
· PRESS AND HOLD a Preset Button for 2 seconds to save the station that you are currently listening to to that Preset Button.
7. Play/Pause Button · Short-press to play or pause audio playback. 8. Volume and Buttons · Short-press the or Buttons to increase or decrease the
speaker’s volume. · PRESS AND HOLD both the and Buttons at the same time
for 3 seconds to change the Left and Right Audio Channel settings for the speaker. Each PRESS AND HOLD will cycle through Left, Right, and Mono. 9. Track Buttons · In Bluetooth Mode, short-press or to skip to the previous or the next track. · In FM Mode, short-press or to tune in a radio station. · In FM Mode, PRESS AND HOLD or to seek a strong station. 10. Party Lights Button · Short-press the Party Lights Button to cycle through the Party Light Modes. · PRESS AND HOLD to turn the Party Lights on / off. 11. Dome Light Button · Short-press to turn on. Each consecutive short-press will cycle through the three Dome Light brightness levels (high, mid, low) and then turn the Dome Light off. · PRESS AND HOLD to turn the Dome Light off.
6

Audio Functions
Connecting and Playing Bluetooth Audio
1. Turn the speaker on and place the speaker into Bluetooth Mode. 2. Short- press the Mode Button until you hear, “Speaker Mode.
Ready to connect,” announced. 3. On your phone’s Bluetooth settings, select `SoundEx-ETA8′ to
pair. If you don’t see the speaker name, turn your phone’s Bluetooth off and on again to refresh the list, or short-press the Bluetooth Button on the speaker to enable Bluetooth pairing again. 4. Wait for a few seconds. Once the pairing and connection are completed, the speaker will announce, “Your phone is connected,” and the Bluetooth LED Status Indicator will light up solid blue.
Change the Speakers’ Audio Channel.
By default, the speakers are set to Mono Mode. Both the L and R Status LED’s will shine green. 1. PRESS AND HOLD both the and Buttons at the same
time for 3 seconds to change the Audio Channel. Each 3-second Press and Hold will cycle through Left (L), Right (R), and Mono Mode. 2. The speaker will announce the Mode audio changes and the appropriate LED Status Indicator will light up. If you have one Amplified Speaker and one Passive Speaker, you only need to make the change on the Amplified Speaker; the Passive Speaker will automatically be assigned to the appropriate Audio Channel, e.g. if you set the Amplified Speaker to the Left Audio Channel, the Passive Speaker will be set to the Right Channel. If you have two Amplified Speakers, you will need to follow the above steps to set up each Amplified Speaker.
7

Audio Functions
Listening to FM Radio
INT
The first time you listen to FM Radio on your ExtremeTower Speakers, check the FM ANT Switch position to make sure it is in the correct position. If you use the Internal Antenna, the switch should be in the INT position. Recommendation: Turn the LED Party Lights off when searching for a radio station. LED lights can create interference with some FM radio frequencies. Station Tuning 1. Short-press the Mode Button to cycle through to FM Mode, the
speaker will announce, “FM Mode.” 2. Short-press or to tune in a radio station.
PRESS AND HOLD or to seek a strong station. 3. Short-press the or Button to adjust the volume. FM Preset 1. PRESS AND HOLD a Preset Button to save the current station to
the corresponding Preset. 2. Short-press a Preset Button to tune to the saved station
corresponding to that Preset Button. 8

Audio Functions
EcoCast ­ Stream Music Between Multiple Speakers
x100
The Amplified ExtremeTower Speaker has EcoCast built-in, which allows the speaker to broadcast (transmit) or receive wireless audio streams to or from other EcoCast-enabled products. EcoCast Streaming: Two Modes Use the Mode Button on the Amplified Speaker to set the speaker into EcoCast Transmitting Mode or EcoCast Receiving Mode: 1. EcoCast Transmitting Mode: When set in this Mode, the EcoCast
Transmitting speaker broadcasts audio to multiple wireless connected EcoCast- enabled speakers. The Transmitting speaker’s audio streaming can be the music played from your phone (via Bluetooth), or FM radio. 2. EcoCast Receiving Mode. When set in this Mode, the Amplified Speaker will receive audio from an EcoCast Transmitting speaker, soundbar, or radio. Notes: · When set to Speaker Mode, the Amplified Speaker turns the EcoCast capability off. · When you have two or more Amplified Speakers or other ECOXGEAR or SoundExtreme speakers bearing the EcoCast
9

Audio Functions
symbol, you can build a broadcast system by initiating EcoCast Transmitting Mode in one Amplified Speaker and broadcasting your music to one or more EcoCast-enabled speakers in EcoCast Receiving Mode. EcoCast: First Two Amplified Speakers

A

B

Follow the steps below to pair two Amplified Tower Speakers:
1. Follow the Connecting and Playing Bluetooth Audio instructions to connect one Amplified ExtremeTower Speaker (Speaker A) to your Bluetooth device. After your device is connected to Speaker A, you can play your desired audio.
2. Press the Mode Button to put Speaker A into EcoCast Transmitting Mode. The Mode LED Status Indicator will flash Red, and the speaker will announce, “EcoCast transmitting.”
3. Power on the other Amplified Tower Speaker (Speaker B) and press the Mode Button to cycle through to and initiate EcoCast Receiving Mode. The Mode LED Status Indicator will flash Green, and the speaker will announce, “EcoCast receiving.”
4. Once the connection between the speakers is successful, Speaker B will announce, “Connection successful,” and start playing audio.
10

Audio Functions
EcoCast: Additional Receiving Speakers B

A

C

D

1. Turn on the additional EcoCast-enabled speakers (Speaker C and Speaker D) and press the Mode Button to cycle through to and initiate EcoCast Receiving Mode. The Mode LED Status Indicator will flash Green, and the speaker will announce, “EcoCast receiving.”
2. On Speaker A (the speaker with the Mode LED Status Indicator shining solid Red), PRESS AND HOLD the Mode Button for 3 seconds. The Mode LED Status Indicator will flash Red.
3. Once the connection between the speakers is successful, Speaker C (and Speaker D) will announce, “Connection successful,” and start playing audio.
Notes:
· If all the speakers are turned off, then turned on, the speaker(s) in EcoCast Receiving Mode (Speakers B, C, and D) will automatically
11

Audio Functions

re-connect to the speaker in EcoCast Transmitting Mode (Speaker A). If they do not automatically re-connected, please follow the above steps to reconnect.
· The EcoCast functionality has a maximum range of 30 feet between speakers.
· While connecting the ExtremeTower Speakers, make sure that the speakers are within a few feet of each other.
EcoCast: Streaming Your FM Radio Station to Multiple Speakers

FM

E

The Amplified ExtremeTower Speaker (Speaker FM) also has the capability to stream FM radio stations to other EcoCast-enabled speakers in Receiving Mode.
When playing an FM radio station, the Amplified Tower Speaker automatically enables EcoCast Transmitting. To receive FM streaming via EcoCast, follow the steps below:
1. Turn on another EcoCast-enabled speaker (Speaker E), press the Mode Button to cycle though to EcoCast Receiving Mode. The Mode LED Status Indicator will flash Green, and Speaker E will announce, “EcoCast receiving.”.
2. On Speaker FM, PRESS AND HOLD the Mode Button for 3 seconds. The Status LED Indicator will flash Red and White.
3. Once the connection between the speakers is successful, Speaker E will announce, “Connection successful,” and start playing audio.
12

Audio Functions

Play Audio Streams From Another EcoCast-Enabled Speaker

T

A

If there is an EcoCast-enabled speaker in EcoCast Transmitting Mode nearby, you can set your Amplified Tower Speaker (Speaker A) to EcoCast Receiving Mode and play audio streams from the EcoCast Transmitting speaker (Speaker T):
1. Turn on your Amplified Tower Speaker, press the Mode Button to cycle though to EcoCast Receiving Mode. The Mode LED Status Indicator will flash Green, and the speaker will announce, “EcoCast receiving.”
2. On Speaker T, PRESS AND HOLD the Mode Button for 3 seconds. The LED Status Indicator will flash Red.
Note: If Speaker T is not an Amplified ExtremeTower Speaker, it may require a different button operation to enter EcoCast Transmitting (Pairing Ready) Mode. Please refer to Speaker T’s User Guide.
3. Once the connection between the speakers is successful, Speaker A will announce, “Connection successful,” and start playing audio.
Note: A speaker in EcoCast Receiving Mode will play at the same volume level (Volume Sync) as received in the audio streams from the EcoCast Transmitting speaker. You can press + or ­ on the EcoCast Receiving speaker to adjust the volume for the EcoCast Receiving speaker only. However, as soon as the EcoCast Transmitting speaker has a playback change (e.g., track change or a volume change), the EcoCast Receiving speaker will once again Volume Sync with the Transmitting speaker.
13

Lighting Control Concepts
LED Lighting Zones, Modes, and Scenes
The Amplified ExtremeTower Speaker can also be controlled by the included SoundExtreme Universal Remote Control and the SoundExtreme Smartphone App. Below are some terms and definitions to help you better understand the Remote Control and the SoundExtreme App.
Zone
A Zone corresponds to all the LED lights that are connected directly to one physical connection on an LED Lighting Controller output, either integrated in the Amplified Tower Speaker or in an ExtremeController (sold separately). When you change a Zone status (on / off, Mode, etc.), the LEDs connected to that Zone will change accordingly. You can control one Zone or multiple Zones at a time.
The integrated LED Lighting Controller on the Amplified ExtremeTower Speaker supports 2 Zones:
· Zone 1 ­ The RGB LED Party Lights behind the speaker.
· Zone 2 ­ The Dome Light on the bottom of the speaker (the Dome Light is a utility light and only shines White).
Mode
There are 3 LED Mode categories, totaling in 44 Modes supported by the RF Remote. The SoundExtreme app can support many more Color Modes.
1. Color Mode: Each Color Mode lights up the LEDs in a solid color. There are 8 Color Buttons on the Remote Control: Red, Green, Blue, White, Orange, Yellow, Cyan, and Purple. You can create a custom color by utilizing the SoundExtreme Smartphone App.
2. Party Mode: There are 20 preset Party Modes accessible via the Remote Control and SoundExtreme Smartphone App. The app
14

Lighting Control Concepts
allows you to customize each of the 20 Party Modes, allowing for nearly unlimited color, cascading, and LED chasing options. 3. Music Mode: There are 16 Music Modes accessible via the Remote Control and SoundExtreme Smartphone App. Scene A Scene is programed via the SoundExtreme Smartphone App. You can customize each Zone into a Scene (a preset). Setting the Scenes on the app allows a 1-button press to bring up your desired custom settings for all of the LED products connected to the LED Lighting Controller. The Amplified Speaker has 5 Scene settings. They are user customizable and programmable. The default Scene settings are: · Scene 1: Patriot 1 · Scene 2: Flowing colors · Scene 3: Zoom · Scene 4: Fading colors · Scene 5: Christmas
15

RF Remote Control

Power Button
Audio Playback Control Buttons Common Buttons: Mode, Scene, Bright, Speed,
and Color
Radio Presets and Remote Pairing Buttons: MFB, P1 · · · P3

Zone Buttons: Z1 · · · Z4
Zone-Mode Buttons: Z1-M · · · Z4-M

Each Amplified ExtremeTower Speaker comes with a SoundExtreme Universal Remote Control.
Basic Functions
1. Power, MODE, and all the Audio Playback Control Buttons on the Remote Control have the same functions as their corresponding buttons on the Amplified Tower Speaker.
Note: If the Amplified Tower Speaker is powered by a removable and rechargeable Battery Pack, and the speaker is turned off, pressing the Power Button will NOT turn on the speaker (infrared remote control is turned off to save battery power when a battery-powered speaker is turned off). You have to press the Power Button on the speaker to turn it on.
16

RF Remote Control
2. LED Lighting Control Buttons: The Amplified Tower Speaker only has two LED Lighting Zones.
· Zone 1 is set for the speaker RGB LED Party Lights on the Amplified Speaker and the Passive Speaker.
Zone 1 LEDs have all the LED Lighting Modes and features mentioned in Section LED Lighting Zones, Modes, and Scenes.
· Zone 2 is set for the Dome Light on the Amplified Speaker. The Zone 2 LED is a (White) utility light with 3 brightness level controls (low, mid and high). Zone 2 does not have any of the LED lighting Modes and features mentioned in LED Lighting Zones, Modes, and Scenes.
· The Z1-M Button and LED Mode Button have the same function, as the speaker LEDs are the only Zone with lighting Mode changes.
· The Z2-M Button controls the Dome Light’s 3 brightness levels.
· Z3, Z4, Z3-M, and Z4-M Buttons do not have functions for this product.
3. MFB, P1, P2, and P3 Buttons:
· When the Amplified Speaker is in FM mode, P1, P2, and P3 Buttons have the same functions as the corresponding Preset Buttons on the speaker.
· In combination with the MFB Button, the P1, P2 or P3 Buttons will let you to pair one Remote Control with up to 3 speakers or to select an individual speaker to control.
Remote Control Pairing and Speaker Selection
The SoundExtreme Universal Remote Control can pair with and save up to 3 speakers in its memory as P1, P2, and P3 speakers. The included Remote Control comes paired with the Amplified Tower Speaker as the P1 speaker. You can use it out of the box to control the speaker after it is powered on.
17

RF Remote Control

If the speaker does not react when you press a button on the Remote Control, check if the battery isolator (clear plastic strip) on the Remote battery compartment is removed (pulled out) completely. Then, follow the steps below.
Remote Control Pairing
1. When the speaker is on, PRESS AND HOLD the < and > Buttons on the speaker at the same time for 3 seconds. The L and R LED Status Indicators and the speaker’s Party Lights will flash Green, indicating the speaker is ready to pair with a remote.
2. PRESS AND HOLD the MFB Button for 3 seconds, then press P1 (P2, or P3) to save the pairing speaker as the P1 (P2, or P3) speaker.
Select a Speaker to Control

1

2

Assuming your Remote Control has paired with Speaker 1 and 2 as P1 and P2 speakers, Speaker 1 is currently controlled by the Remote Control. If you want to use the Remote Control to control Speaker 2, follow the steps below.
1. PRESS AND HOLD the MFB Button for 3 seconds, Speaker P1’s Party Lights will flash Blue, indicating your remote is the process of speaker selection.
2. While Speaker P1 is flashing Blue, press P2. The Party Lights on Speaker 2 will flash Blue 3 times and produce a prompt double-beep tone, indicating Speaker P2 is selected.
3. Press a button on the Remote Control. Speaker P2 will produce the corresponding action, while Speaker P1 will have no response.
18

RF Remote Control
Speaker Party Lights and Dome Light Control
When the Amplified ExtremeTower Speaker is on, you can use the Remote Control to change the Party Lights and Dome Light. Zone 1: Party Lights ­ Lighting Mode Control 1. Press the Z1 Button. The Party Lights will briefly light up Green
in ascending order and then enter Scene 1 ­ Patriot 1 (Red, White, and Blue) or light up a random color pattern. 2. Now you can change the LED Lighting Mode with one of the following button presses: · Short-press one of the 8 Color Buttons to light the LEDs in the corresponding color. · Short-press the Mode or Z1-M Button to cycle through LED Modes. If you want to go back to the previous Mode, you can double-click either the Mode Button or the Z1-M Button. 3. Press the Z1 Button to turn off the Party Lights. Zone 2: Dome Light Control 1. Press the Z2 Button. The Dome Light will turn on. 2. Press the Z2-M Button to cycle through 3 brightness levels (High, Mid, and Low). 3. Press the Z2 Button to turn off the Dome Light.
19

Remote Functions Overview

BUTTON

ACTION
Short-Press

FUNCTION
To turn on / off the Amplified speaker.

Short-Press

To play / pause audio.

Short-Press
Press and Hold (for 3 seconds)
Short-Press

· In Bluetooth Mode: To skip to the previous or the next track.
· In FM Mode: To tune in a station. In FM Mode: To seek a strong station.
To Change Modes.

Press and Hold (for 3 seconds)

To enable EcoCast pairing.

Short-Press

To increase or decrease the speaker’s volume.

Press and Hold Both (for 3 seconds)

To change the Left and Right Audio Channel settings for the speaker.

20

Remote Functions Overview
NOTES
· If the Amplifier Tower Speaker is controlled by the vehicle ignition, when the ignition is on, the Remote can turn the Amplified Tower Speaker off or on. When the ignition is off, the Power Button does not turn the speaker on or off.
· If the Amplified Tower Speaker is powered by a removable and rechargeable Battery Pack, and the speaker is turned off, pressing the Power Button will NOT turn on the speaker (infrared remote control is turned off to save battery power when a battery-powered speaker is turned off). You have to press the Power Button on the speaker to turn it on.
· The Mode LED Status Indicator will change color to indicate the current Mode: Blue ­ Speaker Mode; Red ­ EcoCast Transmitting; Green ­ EcoCast Receiving; White ­ FM
· Each Press and Hold will cycle through Left, Right, and Mono.
21

Remote Functions Overview

BUTTON

ACTION
Short-Press

To turn on / off Zone 1 (Party Lights).

Short-Press

To turn on / off Zone 2 (Dome Light).

NOT APPLICABLE FOR

Short-Press

To cycle through the three LED Mode categories for Zone 1.

Double-Click Short-Press Double-Click

To cycle back to the previous LED Mode for Zone 1.
To cycle through the three Brightness levels for Zone 2.
To cycle back to the previous Brightness level for Zone 2.

NOT APPLICABLE FOR

Short-Press

To cycle through the three LED Mode categories for Zone 1.

Double-Click

To cycle back to the previous LED Mode for Zone 1.

22

Remote Functions Overview
NOTES
· When turned on, LEDs in Zone 1 will light up Green in ascending order. When turned off, the LEDs light up Red in descending order.
THIS PRODUCT · There are 44 distinct LED Modes: 8 Color Modes, 20 Party Modes, and 16 Music Modes. You can also use the SoundExtreme Smartphone App to find a specific LED Mode.
THIS PRODUCT · There are 44 distinct LED Modes: 8 Color Modes, 20 Party Modes, and 16 Music Modes. You can also use the SoundExtreme Smartphone App to find a specific LED Mode.
23

Remote Functions Overview

BUTTON 24

ACTION
Short-Press Short-Press Short-Press Short-Press

FUNCTION
To cycle through the 5 defined Scenes for Zone 1.
To cycle through 5 levels of Brightness for Zone 1.
To cycle through 5 levels of Speed for Zone 1.
To select the corresponding Color for Zone 1.

Press and Hold (for 3 seconds)
Press and Hold (for 3 seconds)
Short-Press
Press and Hold (for 3 seconds)
Short-Press
Press and Hold (for 3 seconds)
Short-Press

To select a speaker to control.
When in FM Mode: To save the current station to the P1 Button.
When in FM Mode: To tune to the station saved to the P1 Button
When in FM Mode: To save the current station to the P2 Button.
When in FM Mode: To tune to the station saved to the P2 Button
When in FM Mode: To save the current station to the P3 Button.
When in FM Mode: To tune to the station saved to the P3 Button

Remote Functions Overview
NOTES
· There are 8 Color Buttons on the Remote Control: Red, Green, Blue, White, Orange, Yellow, Cyan, and Purple. You can also use the SoundExtreme Smartphone App create a custom color.
· Refer to Select a Speaker to Control for more details. · Refer to Select a Speaker to Control for more functions.
· Refer to Select a Speaker to Control for more functions.
· Refer to Select a Speaker to Control for more functions.
25

SoundExtreme App
The Amplified ExtremeTower Speaker can be operated via the SoundExtreme Smartphone App.
Download and Install
For iPhones, download the app from the following URL: https://apps.apple.com/us/app/soundextreme/id1670708941 For Android phones, download the app from the following URL: https://play.google.com/store/apps/details?id=com.cchip.ecoxgear Alternatively, use the following QR Codes to download the SoundExtreme Smartphone App.

iOS

Android

App Overview
Password Secured: The app is password protected so others cannot gain access and control your ExtremeController. The default password is 0000.
Name Your Devices: You can change and customize the name of your devices and Zones, such as Rear speakers, Soundbar, etc.
Set Up Modes: Use the app to set up the LED Mode for speaker LEDs and change the Dome light brightness on your Amplified Speaker. You can also change the Brightness and Speed.
26

SoundExtreme App
Create and save Scenes: A Scene is a preprogrammed light show that you can save for later quick access. We have created 5 default Scenes that are fully customizable and programmable. Set Up a Group: Create and set up a group of devices (multiple Amplified Tower Speakers, or other SoundExtreme products with LEDCast built-in). This will allow all the LED lights connected to different devices to be controlled by the SoundExtreme Smartphone App at the same time. Bluetooth Low Energy: The SoundExtreme Smartphone App relies on a BLE (Bluetooth Low Energy) connection between your phone and the Amplified Tower Speaker. Make Sure you turn on Bluetooth on your smartphone.
Initial App Connection
1. Launch the SoundExtreme App on your smartphone or other BLE-enabled device.
2. On the SoundExtreme App homepage, tap Device Connection List.
27

SoundExtreme App
3. If your Amplified Tower Speaker is powered on, it will show up as LEDs- ETA8 on the app’s Connect Device screen. Tap the device name on the screen. A checkmark will appear on the right. Tap the Connect button.
28

4. A dialog window will popup asking you to enter a password. The Amplified Speaker default password is 0000. After entering the password, click the Confirm button. The app will show the device is connected. Tap the Back button on the top-left. It will take you to the Device List screen.
5. Select your speaker, it will take you to the Scene screen. There are 5 factory pre-defined scenes on the Amplified Tower Speaker. Tap the On / Off button at the right for Scene 1, the Party Lights will light up Red, White, and Blue, which is the LED Lighting Mode defined for Scene 1 ­ Patriot 1.

SoundExtreme App

29

SoundExtreme App
Set Up Zones
You can set up the LED Light Mode for Zone 1 (Party Lights) with the following steps: 1. On the Device List screen,
select your Amplified Tower Speaker (LEDs-ETA8) and the app will bring you to the Zone screen. 2. On the Zone screen, Tap Zone 1 and you will go to the Zone LED Mode Settings screen. There are 3 tabs: Color, Party, and Music, which allow you to select a solid Color, a Party Mode, or a Music Mode. · When you choose a Mode, the LEDs connected to the Zone you selected will light up accordingly, giving you a preview.
30

SoundExtreme App
· If you tap the Save button on the screen, the app will save your setting for the selected Zone.
· If you tap the Cancel button or exit the LED Mode Settings screen, your Mode selection will not be saved and LEDs connected to that Zone will display the previously selected LED Mode.
3. After you set up the Modes for each of the Zones, the controller setup is complete. 31

SoundExtreme App
Control Speaker Dome Light
You can control the Amplified ExtremeTower Speaker Dome Light with the following steps: 1. On the Device List screen,
select your Amplified Tower Speaker (LEDs-ETA8) and the app will bring you to the Zone screen. 2. On the Zone screen, Tap Dome/Light Bar (Zone 2) and you will go to the Dome/ Light Bar Settings screen. 3. There are 3 brightness levels (High, Mid, and Low) on the slide bar for you to choose from. 4. You can also set a countdown timer for the Dome Light by tapping Count Down. Set up a time on the countdown timer from the popup window. Once the countdown is over, the app will turn off the Dome Light.
32

Set Up Scenes
1. On the Device List screen, select your Amplified ExtremeTower Speaker (LEDs-ETA8) and the app will bring you to the Zone screen. Tap the Scene tab. The app will show 5 predefined scenes on your Amplified Tower Speaker.
2. You can change a Scene’s LED settings by selecting any of the 5 Scenes. When you select the Scene, you will go to the LED Mode Setting screen. You can use the same procedure as in the Set Up Zones section to set up each Zone and save the Scene’s new LED settings.
3. After you set up LED Modes for all the Zones, the setup is complete for the selected Scene.

SoundExtreme App

33

SoundExtreme App
Change Password
To add extra security, you can change the default password of 0000 to your desired 4-digit numeric password. Please note that the password is stored in your Amplified ExtremeTower Speaker, not the SoundExtreme App. So, after you change the password, please make a note in case you forget your password. The password won’t be reset by reinstalling the app or changing to another smartphone. The only way to reset your password is to conduct a factory reset on the Amplified Tower Speaker.
Follow the steps below to change your password:
1. Select the Menu at the top-right corner of the screen.
2. Select Device Password from the menu.
3. Once at the Device Password screen, select the device that you want to change the password to.
4. Enter the current password, the new password, and re-enter the new password. Then tap the Confirm button.
34

SoundExtreme App
5. If the change is successfully saved, the app will display a confirmation message.
This is a one-time event. You do not have to enter in your password every time you launch the app, as your app will remember your password.
Factory Reset
If you forget the password, you will need to do a Factory Reset on the Amplified ExtremeTower Speaker so that the password is reset to its default value: 0000.
· When the Amplified Tower Speaker is on, PRESS AND HOLD the P1 and P3 Buttons on the speaker at the same time for 3 seconds. The speaker will produce a prompt triple-beep tone indicating that the Factory Reset is successful.
Note: Besides the password reset, a Factory Reset will also configure the Amplified ExtremeTower Speaker to the following Factory Settings:
· The Party Lights (Zone 1) is set to Scene 1 with the Brightness set to 100% and the Speed set to 80%.
· All the 5 configurable Scenes are set to the Factory Default Scenes.
· All the 3 FM station Presets are cleared.
· All the Bluetooth pairing records are erased. 35

Specifications
Dimensions
7.26 in / 184 mm 11.93 in / 303 mm
4.64 in / 118 mm
36

13.42 in / 341 mm

10.49 in / 267 mm

8.94 in / 227 mm

Weight – Passive Speaker 9.66 lbs / 4.38 kg (with mount); 8.16 lbs / 3.7 kg (without mount)
Weight – Amplified Speaker without Battery 10.32 lbs / 4.68 kg (with mount); 8.82 lbs / 4 kg (without mount)
Audio Output Power 300 Watt max (100 Watt RMS)
Tweeter 1.5” (38 mm) tweeter, 4 ohms
Woofer 8” (203 mm) low and mid-range woofer, 3 ohms
Bluetooth Compliance Bluetooth® 5.1
EcoCast Range 30 ft / 9.1 m between Transmitting speaker and Receiving speaker
FM Radio Frequency Range US: FM 87.5 – 107.9 MHz
Frequency Response 35Hz ­ 21KHz
Sensitivity 92dB + – 3dB @ /1W/1m Built-in, two-way crossover network

Specifications

Power Input 12V, 20A
Blade Fuse 20A, 32V
Speaker Party Lights Addressable RGB LEDs
Rechargeable Battery Pack (if included) – Power 12V, 13.4Ah Lithium-Ion
Rechargeable Battery Pack (if included) – Weight 1.81 lbs / 0.82 kg

Battery Charger (if included) – Input 100 – 240VAC 50/60Hz, 0.6A
Battery Charger (if included) – Output 12V, 2.0A
Storage Temperature -40°F to 122°F / -40°C to 50°C
Operating Temperature 23°F to 95°F / -5°C to 35°C

37

Important Legal Information
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference, and 2.) This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator to your body. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, consult the dealer or an experienced radio/TV technician for help.
RF WARNING STATEMENT:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1.) This device may not cause interference, and 2.) This device must accept any interference, including interference that may cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and follow all instructions. Use only as intended. The ExtremeTower speakers are intended to be used indoors or outdoors and in land or water environments. The speakers have been tested to IP66 waterproofing standards, which means the speakers can be exposed to dust and water, but should not be submerged underwater. The speakers are NOT intended for underwater use. Always make sure the cap(s) / cover(s) are clean, free from sand or debris, and correctly fitted. The speaker will only meet IP66 ratings if all rubber seals, gasket(s) and cover(s) / cap(s) are in place. If you notice a muffling of audio after submersion, gently shake the unit to clear excess water. If your speaker is exposed to salt water, clean it thoroughly after use with fresh water. The power cables and the unit with an improperly fitted cap are NOT waterproof. To prevent fire or shock, do NOT attempt to power this unit if it is wet or you suspect water has entered the unit. In this situation, please return the unit to Grace Digital for a free assessment. If we have found that the unit has carried water, we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended. CAUTION: Do NOT open to repair. A qualified technician must carry out repair work. ATTENTION: Do NOT remove the battery while the unit is wet. Towel dry the unit AND make sure all connections are
dry BEFORE removing the battery to recharge. Failure to do so may result in electrical damage to the unit and may void the warranty. ATTENTION: Do NOT connect to a 12VDC power supply while the unit is wet. Make sure all connections are dry BEFORE connecting to a power source. Failure to do so may result in electrical damage to the unit and may void the warranty. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov WARNING: Danger of explosion if battery is incorrectly charged. ATTENTION: Do NOT dispose of in a landfill. Contact SoundExtreme at www.gracesupport.com or a certified recycling agent to dispose of the unit.
SAFETY:
This product has a limited life span of use and should be replaced when it shows obvious signs of wear.
38

Important Legal Information
Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit, allowing water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock. Please exercise care and good judgment when using your ExtremeTower speakers. Audio levels should be appropriate to your environment, comply with all local regulations, and always ensure that you can hear and be aware of any potential hazards around you. You should always
1.) Use the ExtremeTower speakers in accordance with any music or noise rules and regulations. 2.) Properly seal the ExtremeTower speakers prior and after each use when in humid or water environments to avoid
water damage to the internal components. Salt water / air is particularly corrosive. Always make sure that the gaskets are sealed when in a salt water environment and that the unit is properly rinsed off after use. 3.) Properly clean the ExtremeTower speakers and ensure the gaskets have no sand, dirt, or water on them prior to storage. 4.) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit. 5.) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit. 6.) Return the unit to SoundExtreme if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the integrity of the unit to take on water. You should never 1.) Never power your ExtremeTower speakers if you suspect water has entered the device. Powering a device with water inside could be potentially hazardous and cause fire or a spark. 2.) Never use your ExtremeTower speakers if you have dropped it on a hard surface which may have destroyed the integrity of the speaker, housing, or gaskets. In the event of a severe impact to your unit, please return the unit to SoundExtreme to review for potential damage. 3.) Never open the jacks or covers in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and cause a fire or a spark. 4.) Never attempt to fix, repair your ExtremeTower speakers. Please send it back to Grace Digital for any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
1.) The unit is waterproof only when the caps and door are properly closed. 2.) Close the caps and door properly before use. If the unit is placed in a water environment without the caps or door
properly closed, water may enter into the unit and void your warranty. 3.) Dry unit completely before opening the caps. Do NOT open the caps if wet or in a wet environment. 4.) Do NOT apply excessive force to any surfaces of the unit when wet or in a wet environment. 5.) Do NOT use or store the unit in places with high temperature. 6.) AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields. 7.) Periodically check the rubber seal on the caps and door for premature wear. 8.) Periodically clean the rubber with a soft moist cloth and ensure no objects such as dirt, hair, sand are on the rubber
seal ring. Do NOT use any oily solvent or chemicals for cleaning. 9.) Rinse off the unit with tap water after use in salt water. 10.) Noise and audio distortion may occur when the batteries are nearing end of charge. 11.) Do NOT remove the grill covers. 12.) Power the unit by attaching the Power Cable intended for use with the unit. The unit must be connected to a 12VDC
power source. If the vehicle battery terminal voltage is not 12V, you will need a DC­DC converter with output 12V. Connecting the unit to a non-12VDC power source will lead to a malfunction or damage to the unit.
LIMITED MANUFACTURER’S WARRANTY:
The ExtremeTower speakers are covered by a 1-year limited warranty that covers defects in workmanship and / or materials for a period of 1 year from original purchase date. This warranty does not apply to any products which have been abused, neglected, modified or used for a purpose other than the one for which they were manufactured. Please refer to the above care and maintenance instructions for suggested care details. The warranty is valid only for the original owner who purchases the unit from an authorized dealer. Transfers do not qualify for warranty protection. SoundExtreme reserves the right to replace any out-of-stock or discontinued product with a comparable product. Discontinued products may not be available for warranty replacement. Any contents are NOT covered by the limited manufacturer’s warranty. Warranty terms may be revised without notification at the discretion of the manufacturer. Please visit www.soundextreme.us for additional product & warranty information.
39

40

ExtremeTower by SoundExtreme Inc., Houston, Texas. Designed in Texas. Made in China.
This product is protected under patent US 9,307,307 B2 and several patents pending.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SoundExtreme User Manuals

Related Manuals