napcat 2A86W-R1 Wi-Fi Video Doorbell User Guide
- June 2, 2024
- napcat
Table of Contents
napcat 2A86W-R1 Wi-Fi Video Doorbell User Guide
Technical Support: support@napcat.net
Official Website: www.napcat.net
Facebook
YouTube
Instagram
TikTok
What’s in the Box
Introduce the Video Doorbell
Introduce the Wi-Fi Doorbell Chime
Set up the Chime
Fix the power connector to Wi-Fi Doorbell Chime
Step1. Place the power connector over Wi-Fi Doorbell Chime as indicated.
Step2. Align the raised slots of the power connector with the notch on the
base of the doorbell chime.
Step3. Push hard in the direction as indicated to lock the power connector in
place.
Note: Power plug may vary in different regions.
Set up the Doorbell on phone
Follow the steps below to get started with your new doorbell.
Step 1. Download the “Napcat Life” App Get the “Napcat Life” app from the APP
Store or Google Play.
Or download the APP by scanning below QR code.
Step 2. Login and add device 1. Run the “napcat Life” app, sign up for a
Napcat Life account.
2. Login with your account ID, tap”+ Add Device”and scan the setup QR code on
the Doorbell Chime.
3. Plug the chime into the power socket at your desired location. The LED
indicator turns blinking red, when the doorbell chime is ready for setup.
4. Extend Wi-Fi Doorbell Chime’s antennas. we recommend that you place the
antenna upward and try not to have anything blocking it, as this will provide
better WiFi quality.
5. Follow the onscreen instructions to finish the initial setup.
Install the Doorbell
Step 1. Finding a Mounting Spot
Take the video doorbell to your front door and check the live view on the App
at the same time. Find a location where you can get the desired field of view.
Consider the below factors:
- Check if you can reuse the existing holes and anchors on the wall or door frame.
- If you want to place the doorbell close to a side wall, make sure the wall doesn’t show up in the field of view. Otherwise IR light will be reflected and night vision will become blurry.
- If you are drilling the mounting holes for the first time, the recommended mounting height is 55″ / 1.4 meters from the ground.
- Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side.
Step2. Find a suitable height to place the Screw Hole Positioning Card.
Step3. Determining the power option
Option 1 – Battery Powered
-
If you don’t have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick.
-
If the doorbell battery is low, you need to charge it before installing it.
-
Mount the Bracket, Please NOTE That The Mounting Bracket has a positive indicator showing the installation direction pointing upward from the ground.
-
Place the Screw Hole Positioning Card
-
Drill and install anchors.( Anchors are not required if the wall is made of wood)
-
Mounting Bracket (If the installation surface is smooth and dust-free, you can use 3M tape along the edges behind the mounting bracket, eliminating the need to drill holes)
-
Screw the mounting bracket into position.
-
Install the 15° mounting wedge if you wish to see more on a specific side.
4. Align the slot of the doorbell with the bracket buckle, put it in, and press it down until it clicks into place.
Congratulations, you have completed the doorbell installation !
Option 2 – Doorbell Wire Powered
-
If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you don’t need to detach and charge it after installation.
-
Ring the existing doorbell to check if it is working. If the doorbell doesn’t ring, your doorbell wires may be defective. Power the doorbell on its own battery or consult an electrician to fix the wires first.
-
Shut off the doorbell power supply. If you’re not sure, shut off the main power supply in your house. Turn the lights in your home on / off to make sure the electricity in your house is properly shut off.
NOTE Always be careful when handling electricity wiring. If you’re not comfortable to do it yourself, do consult a qualified electrician. -
Find the doorbell chime in your house, then remove the cover and find the screw terminals with TRANS and FRONT markings. Use the provided Jumper for Existing Chime to connect the two terminals. This is to bypass the doorbell chime and will not affect the normal operation of the circuit.
NOTE:
· The video doorbell requires user to bypass the existing chime first to get sufficient power. Without this step, the video doorbell will still be able to power on but will operate unstably.
· In most cases, the existing doorbell circuit looks like below chart. Find the existing doorbell chime in your house, remove the cover and take a photo of the wire connection in case you need to reconnect it.
· Use the provided jumper to connect FRONT and TRANS terminals to bypass the chime on the circuit. Do not remove the original wire connecting to the chime. If your doorbell chime has different markings or you have multiple chimes, do consult a qualified electrician.
· When the jumper is in place, the existing chime will not sound anymore. -
Remove the existing doorbell button at the front door. Pull the two wires out carefully when removing the old doorbell. Straighten the wire ends if necessary.
Mount the Bracket, Please NOTE That The Mounting Bracket has a positive indicator showing the installation direction pointing upward from the ground. -
Place the Screw Hole Positioning Card
-
Drill and install anchors.( Anchors are not required if the wall is made of wood)
-
Mounting Bracket (If the installation surface is smooth and dust-free, you can use 3M tape along the edges behind the mounting bracket, eliminating the need to drill holes)
-
Screw the mounting bracket into position
-
Install the 15° mounting wedge if you wish to see more on a specific side.
-
Connect the wires to the two terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal as the electric current is alternating current.
Note: To prevent short-circuit, make sure the wires are not touching each other after connecting them to the terminals. Use electrical wiring tape to secure the connection if the wall doesn’t have space for wire nuts. -
Align the slot of the doorbell with the bracket buckle, put it in, and press it down until it clicks into place.
-
Switch the doorbell or master circuit breaker to ON.
Congratulations, you have completed the installation !
Detach the Doorbell
- Use the doorbell detaching pin provided if you wish to detach the doorbell from the Mounting Bracket.
- Press and hold the Release hole on the bottom of the doorbell and then lift its bottom to take it off.
Note: If you have enabled Anti-Theft Siren, please disable it via the “Napcat Life “app first, otherwise the alarm will be triggered.
Notification of Compliance
Compliance Statement
This device complies with Part 15C of FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation. Warning: Changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving an tenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.”
Simplified EU Declaration of Conformity
Napcat declares that this device is in compliance with the essential
requirements and other relevant provision of Directive
EN300328,EN301489-1,EN31489-17,EN IEC 62311EN IEC 62368.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environment safe recycling.