QINGDAO MWH630B WiFi BT Module User Manual
- May 15, 2024
- QINGDAO
Table of Contents
QINGDAO MWH630B WiFi BT Module
The product description
The user can achieve a TV connection WIFI net, through this module and the voltage supplied by the system the module needs to be transmitted by a voltage regulator or circuit This equipment may be operated in all European countries. The module installation method is as follows: pass the large round hole of the module through the limit column of the bracket of the TV, and fix the module by the snap-fit on the bracket.
Basic parameters
RF output power
The display method of Model approved code
In the factory, the model approval code is displayed on the PCB board through
silk screen printing. 5. FCC Statement This equipment has been tested and
found to comply with the limits for a Class B digital device, under part 15 of
the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and if not installed
and used by the instructions may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures：
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. 6. Radiation Exposure Statement This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled environment
and it also complies with Part 15 of FCC RF Rules. This equipment should be
installed and operated with a minimum distance of 20 in (50cm)between the
radiator and your body. This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
CAUTION
To comply with the limits of the Class B digital device under Part 15 of the
FCC Rules, this device is compliant with Class B limits. All peripherals must
be shielded and grounded. Operation with non-certified peripherals or non-
shielded cables may result in interference to radio or reception MODIFICATION
To assure continued compliance, Any changes or modifications not expressly
approved by the grantee of this device could void the user’s authority to
operate the device. 7. Radiation Exposure Statement This equipment complies
with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 50
cm(8 in )between the radiator and your body
NOTE
To satisfy FCC exterior labelling requirements, the following text must be
placed on the exterior of the end product Contains Transmitter module FCC
ID:**** To satisfy IESD exterior labelling requirements, the following text
must be placed on the exterior of the end product.
Contains Transmitter module IC
This symbol on the product or its packaging indicates that this product must
not be disposed of with your household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product. The device
is restricted to indoor use only when operating in the 5150 to 5350 MHz
frequency range.
IC Statement
where applicable, antenna type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement outlined in section 6.2.2.3 shall be indicated. This device
complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions: “Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. Manufacturer: Qingdao Intelligent & Precise
Electronics Co., Ltd. Address: No.218 Qianwangang Road, Qingdao Economic &
Technological Development Zone, Qingdao City, Shandong Province, P. R. China
Importers
Hisense France SAS
Address: 9 Rue des 3 Soeurs, 93420 Villepinte, France
Hisense Iberia, S.L.U
Address: Ronda Auguste y Louis Lumiere. 23 Nave 12. Edificio Lumiere – Parque
Tecnológico 46980
Paterna (Valencia) – Spain
Hisense Italia S.r.l
Address: Via Montefeltro, 6/A, 20156 MILANO
Hisense South Africa
Address: The Estuaries, Building 17 Oxbow Crescent, Century City, Cape Town, South Africa： Without approval, companies, businesses, or users are not allowed to change the frequency, increase power, or change the characteristics and functions of the original design low-power RF equipment that has obtained the verification certificate. The use of low-power RF equipment shall not affect flight safety or interfere with legitimate communication; When interference is found, it should be immediately stopped and improved until there is no interference before continuing to use. Legal communication refers to wireless communication operated by the provisions of the Telecommunications Management Law. Low-power radio frequency equipment must withstand interference from legitimate communication or industrial, scientific, and medical electromagnetic wave radiation electrical equipment.
EU DECLARATION OF CONFORMITY
It is hereby declared that the following designated product: Complies with the
essential protection requirements of Directives on Radio Equipment Directive
2014/53/EU, Restrictionofthe Certain Hazardous Substances in electrical and
electronic equipment (Directive 2011/65/EU), Eco-design RequirementsforEnergy-
Related Products (Directive 2009/125/EC) and their amendments. The assessments
were based on the following regulations and standards.
This declaration is the responsibility of the manufacturer:
Qingdao Intelligent&Precise Electronics Co., Ltd. No.218 Qianwangang Road,
Qingdao Economic & Technological Development Zone, Qingdao City, Shandong
province, P. R. China
Authorised person signing for the company:
Name:Wang Haining
Title:Certification Engineer
Name in block letters & position in the company
Qingdao, 11, March 2024 Signed
Place & date
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>