Zhongshan Emertes Electronic Technology WL1-722WH Portable Power Station User Manual

PRODUCT MANUAL **Structure description

**

1. LCD screen
2. Recharging interface
3. USB-0C3.0 (Quick charge output port
4. USB-A output port
5. TYPE-C-PD 60W (input & output port)
6. TYPE-C output port
7. DC12V output port
8. Cigarette lighter output port
9. AC inverter output port
10. Ring light (traffic warning light & SOS help light)
11. Wireless charging

The AC/DC interface has the function of automatic load identification, but it will shut down automatically if the equipment cannot be recognized when the power is too low. It can be forced to open the interface by long press 2S, and it must be closed manually when the power is shut down.
Interface and function description
1. LCD screen
A. Total output power: display the total output power of all ports in watts:
B. Power indicator: shows the percentage of remaining power and the number of remaining batteries.
When the power is full, it will close the LCD screen automatically.
If 20% power, the buzzer will “beep” one time.
If 10% power, the buzzer will “beep” two times and AC output closed.
If 5% power, it will remind you to recharge by “beep” three times.
C. Remaining time: calculate the remaining time according to current total output power and existing power. When showing the number in the non-flashing state, it means remaining working time by hours, if flashing state, it means remaining working time by minutes.
D. Over temperature protection:

1.  When the battery temperature exceeds 60 Celsius in the charging state, it starts over-temperature protection, if the temperature is less than 50 Celsius, protection is released.
2. When the battery temperature exceeds 50 Celsius in the recharging state, it starts over-temperature protection, if the temperature is less than 40 Celsius, protection is released.
3. When key components working temperature exceeds the setting rated value in AC/DC mode, it starts over-temperature protection.

E. Fan cooling indicator light: the cooling fan will turn on automatically when the temperature reaches the control value.
F. Overload & short circuit protection: It will stop output warning with “beep” ringing when overloaded or short-circuited.
G. Port usage status identification. When the TYPE-C-PD port is plugged into input/output devices, the corresponding display characters will light up, and when the AC/DC/wireless charging button is pressed, the corresponding identification lights up.
2. Recharging interface
Support three recharge ways:

1. adapter;
2. solar panel;
3. cigarette lighter.

It provides short circuit, over recharge, adaptive recharging protection.

3. USB—QC3.0 (quick charge output port)
Two independent quick charge ports, support quick charge devices with QC3.0 protocol, USB compatible as well. The max output is 18W (5V/ 3A, 9V/ 2A, 12V/ 1.5A) providing short circuit, overload, overcharge, over recharge protection.
4. USB—A output port
USB—A output port, the Max output is 5V/ 3A, providing short circuit, overload, overcharge, over recharge protection.
5.TYPE-C-PD 60W (input & output port)

1.  It can support bidirectional power transmission: Input(recharging) and output(with load). Standard power is 60W, Max 65W;
2. When the TYPE—C port connects to devices, the indicator will light up automatically. When pulling out the devices, it turned off;
3.  Identify the device under PD protocol automatically, compact 5V/9V/12V/15V/20V 3A output;
4.  This port has a short circuit, overload, overcharge, over recharge protection functions.

6. TYPE—C output port
TYPE—C output port, the Max output is 5V/ 3A, providing short circuit, overload, overcharge, over recharge protection.
7. DC 12V output port
The port connects with DC 12V devices or auto electrical parts freely, the two ports support 120W/ 10A Max in total. (the output current of each independent port is 10A Max among 2 ports). These 2 ports provide short circuit, overload, overcharge, over recharge protection functions.
8. Cigarette lighter output port
The Max output is 12V/ 10A, providing short circuit, overload, overcharge, over recharge protection.
9. AC inverter output port
Pure sine wave output.
555Wh: 500W (standard), 590W (Max.);
722Wh: 700W (standard), 800W (Max.);
With overload, short circuit, over-temperature, over-discharge, and other protection functions, it can support all AC electrical equipment within power range.
10. Ring light (traffic warning light & SOS help light)
Offering warm white, cool white, neutral white three-color as a ring light. When a car gets into danger on road, the warning light could indicate other vehicles avoiding. This flashlight could switch to SOS mode when people are in danger.
11. Wireless charging
Supports mobile phones with a wireless charging function. Max output power is 10W. Identify devices automatically.
The AC/DC interface has the function of automatic load identification, but it will shut down automatically if the equipment cannot be recognized when the power is too low. It can be forced to open the interface by long press 2S. and it must be closed manually when the power is shut down.

Technical parameters

General|
---|---
Weight| 7KG/8KG
Specification| 236.5x220x226mm
Working temperature| Operating temperature in charging state: 0 – dOt Operating temperature in the non-charging state: -10 – 50`C
Storage temperature| 0 – 35t
Certification| CE-RED PSE FCC-ID RoHS UN38.3 MSDS IEC62133
Input|
DC input port (adapter/solar/cigarette lighter)| DC 7909 port Charging voltage: DC10-30V / constant 80W
Type-C-PD input port| Type-C-PD port I5V/9V/12V/15V/20V, 3A)
Output|
Type-C-PD output port (x1)| Type-C-PD port 15V/9V/12V/15V/20V, 3A)
Type-C output port NH| Type-C port (5V/3A Max)
USB-0C3.0 quick charge output port ix2)| USB port I5V/3A,9V/2A,12V/1.5A)
USB-A output port 1×2)| USB port 15V/3A Max)
DC 12V output 1×2)| DC 5521 port II 2V/10A)
Cigarette lighter output port(x1)| Cigarette lighter port 112V/10A)
AC DC inverter AC output| AC universal socket/AC socket (US)/ AC socket 1.1P1
Internal|
Battery type| 18650 batteries
Battery capacity| 555Wh/ 722Wh
Warranty| I year

charge way
Please charge the battery before using or storing it. The indicator will light up and the battery symbol run. The LCD screen will display the current charging percent and power at the same time indicator light lighting up. When the LCD screen displays 100%, it means the power is full. The current power can be viewed through the LCD screen.

100W Solar panel
(The charging time is determined by the sunlight intensity)
Support MPPT charging of solar panel.| as13 hours| ..16 hours

The data is only for reference. charging time will be different due to the environment, methods, and other factors.
Malfunction elimination

the charger, equipment, and electricity are connected well.
2. Connected property, but the battery indicator does not run.| The charger is broken, please contact the after-sale service.
3. Connected properly, still unable to recharge.| Battery temperature is too high (caused by high storage temperature or the battery just discharged, not cooled yet).
No output| 1. The connecting line between equipment and devices unproperly.| Make sure the equipment and devices are connected properly.
2. The output port switch does not open (type-C port does not need open, it can be identified automatically).| Turn on the output port switch, and the indicator light will be on.
3. Low power (when the power is less than 10%. the AC output will be turned off automatically, and the DC can work normally. If the AC is needed in an emergency, it can be forced to start by pressing the AC key long time for 5 seconds).| Recharge the equipment in time.
4. Still no output after checking 1.2.3 steps.| Damaged or other malfunction, please contact the after-sales department
Interrupt with device| 1. The device rated or instant power exceeds the rated power of equipment it will interrupt.| Choose a more powerful outdoor power supply model.
2.1twill turn off the output due to operating temperature protection by battery or key components.| It will start work when the equipment cools down.
3.0vedoad a short circuit.| The output recovers after the malfunction is saved.
4. When the power of the load equipment is too small, the equipment cannot be identified and will shut down automatically.| Press 2S to force the machine to start, and it must be closed manually when the machine is shut down.
5. The output still shut down after checking the 1.2.3.4 steps.| Damaged or other malfunction, please contact the after-sales department.

Warning & Caution

Please follow basic precautions including
 A.Please read all instructions before using the product.
B. Please supervision your children when using the product.
C.Do does not use accessories made by non—professional manufacturers avoiding electronic shock risk.
D.Please take off the power plug while no use.
E.Do not disassemble, repair or modify the products to avoid fire, explosion, or electronic—shock risk.
F.Do does not use damaged wires, plugs, or cables to avoid electronic—shock risk.
G.Please charge and discharge the product in a well—ventilated place, do not restrict the ventilation of the product in any way.
H.Please place the product in a ventilated and dry place to avoid electric shock by getting water.
I.Do not place the product close to or in a fire or expose it to heat. It may lead to a fire/explosion accident.
J.Do not use or place the product under high temperature (in hot sunlight or in a hot car), otherwise it may cause the battery to overheat, fire, function failure, shorten the lifespan, or other risks.
K.To preserve the battery low power, please use and recharge at least once every 3 months.
L.Take off the plus in time when the product is fully charged to avoid possible accidents.
Warranty
The warranty period is 12 months. The warranty period starts from the purchase date. To estimate the start time, your purchase certificate or other reasonable documents shall be provided.
Exclusions

1. The appearance of the product is damaged after use.
2. Disassembled and repaired on your own.
3. Performance failure is caused by human factors.
4. Damage caused by natural disasters, lightning, accidents, and other irresistible factors.

FCC Statement

This device complies with part 15 and part 18 of the FCC Rules. Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority tooperate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and any other radio device.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>