SUPERATV XP 1000 Polaris RZR 3 Inch Long Travel Kit Chromoly Tubed Instruction Manual
- June 4, 2024
- SUPERATV
Table of Contents
SUPERATV XP 1000 Polaris RZR 3 Inch Long Travel Kit Chromoly Tubed
Read instructions and view illustrations before beginning
PRODUCT DESCRIPTION
Item
| Description
---|---
A
| Upper Right
B
| Lower Right
C
| Upper Left
D
| Lower Left
Keep all components removed from machine
– remove Arms from Frame
– repeat for opposite side
A-Arms Prep
PIVOT BLOCK SETTINGS
-
Place new A-Arms onto a flat surface and verify dimension shown.
-
Negative 1° camber setting is achieved when Pivot Blocks are set to this dimension.
-
See last page for additional camber information.
-
Install Lower Left (D) to Frame with stock hardware. Leave Nuts loose until all final adjustments have been completed.
-
Install Upper Left (C) to Frame with stock hardware.
Tighten hardware completely; SuperATV recomends using Loc-Tite.
-
Reinstall Knuckle to A-Arms; do not tighten lower hardware completely.
-
Secure Sway Bar Link, Caliper, and Shock with stock hardware.
-
Reinstall Hub and Axle hardware.
-
Secure Brake Lines to Upper A-Arms with components shown.
-
Reinstall Tires and check Camber settings; see last page.
-
Tighten all hardware completely. SuperATV recommends using Loc-Tite on Nuts.
CAMBER
- Tires must have equal air pressure before making adjustments.
- Adjustments to be made after all suspension components have been completely assembled.
- Tires must not be in contact with ground when making adjustments.
- Perform adjustments in small increments.
Adjusting Camber:
- Remove A-Arms from Frame and turn Pivot Blocks to adjust camber. Reinstall Arms.
- Lower machine and settle suspension components by rolling machine back and forth several feet at a time.
- Check settings and make small adjustments as needed.
- Each time an adjustment is made, machine must be rolled back and forth to settle suspension components.
- Once desired setting is achieved, tighten hardware completely. Loc-tite on Nuts is recommended.
A NEGATIVE CAMBER SETTING OF 1° to 2° IS RECOMMENDED.
LOWER:
Too much positive camber: adjust Pivot Blocks OUT.
Too much negative camber: adjust Pivot Blocks IN. note: 2 full turns is 1°
UPPER A-ARMS:
Too much positive camber: adjust Pivot Blocks IN.
Too much negative camber: adjust Pivot Blocks OUT. note: 2 full turns is 1°
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact
SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Need help with your installation?
|
sales@superatv.com
---|---
|
1-855-743-3427
|
www.superatv.com
| 8:00am –
8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>