PROEL SW2100A Active Subwoofer User Manual

PROEL SW2100A Active Subwoofer

KEY FEATURES

• Band-Pass/Bass-Reflex Active Subwoofer
• Single 21” Neodymium woofer with 4” ISV voice coil
• Water repellent cone
• Compact cabinet with very good output-to-weight ratio• 18mm birch plywood enclosure with Heavy duty castors
• 4000 Watt Class D amplifier with PFC Switch Mode Power Supply
• 96KHz / 40-bit floating point CORE processing with PRONET AX remote control
• Optimized presets for use in combination with AX12C line array modules

INTRODUCTION

The SW2100A is a very compact Band-Pass/Bass-Reflex subwoofer providing high output and extended low-frequency response.
It is equipped with a single 21” neodymium transducer with a 4” ISV voice coil, large displacement suspension system, and composite reinforced, water- repellent cone, able to provide clean and undistorted LF reproduction at very high SPL.
The system processing is based on the CORE DSP platform designed by the PROEL R&D
Laboratories using one of the most advanced SHARC DSPs for audio applications. It features 40bit, 96kHz floating point resolution, and top-quality 24bit AD/DA converters, for perfect signal integrity, dynamic range over 110dB, and superior sonic performance. The PRONET

AX control software, working on a solid and reliable CANBUS-based network protocol, provides an intuitive interface for the remote control of the whole system, with the possibility of EQing, delaying, managing the protection functions, and monitoring the status of the amplifier.

The SW2100A is powered by a DA SERIES digital power module, a new generation of CLASS D
power amplifier with digitally-controlled SMPS. The innovative technology used for these amplifiers (including also the use of a variable switching frequency) offers performance at the top of the range, such as superior sound definition at any audio frequency, very high dynamics for low-level signals, and very low distortion even at maximum power. The DA module employed for powering the SW2100A features also PFC (Power Factor Correction), a technology able to guarantee always the highest level of power regardless of any eventual fluctuations of the power supply.

The SW2100A has been mainly designed to provide the optimal low-frequency extension to the AX12C line array module. The built-in DA power module can provide 2000W to drive the 21” woofer and 2000W to power up to four AX12C line array modules connected to the output SPEAKON. The built-in CORE DSP provides 4 presets for different combinations: 2, 4 or 1 columns plus 1 user preset (additional presets for processing other AXIOM speakers are also available).

The SW2100A features on the top panel a special metal plate and it comes with a dedicated aluminium bracket for fast coupling with the AX12C’s rigging hardware. Using this simple system, up to two AX12C modules can be easily installed on an SW2100A.

TECHNICAL SPECIFICATION

I/O AND CONTROL OPERATIONS

WARNING! Connect no more than one subwoofer unit to the MAINS~ OUT connector.
WARNING! If you use the MAINS~ OUT turn on each subwoofer unit one at a time.
WARNING! In the case of product failure or fuse replacement, disconnect the unit completely from the main power.
WARNING! Use a suitable power cable and mains plug to build the power cable, it must only be connected to a socket corresponding to the specifications indicated on the amplifier unit. See assembly instructions downloadable from the NEUTRIK WEB site at: http://www.neutrik.com/

ON – This LED indicates the power-on status.
PROT – This red LED lights when the amplifier module is in protect mode for an internal fault and, consequently, the amplifier is muted.
SIGN LIMIT – This LED lights in green to indicate the presence of the signal and lights in red when an internal limiter reduces the input level. INPUT – Audio signal input with locking XLR connector. It has a fully electronically balanced circuitry including AD conversion for the best S/N ratio and input headroom.
LINK – A direct connection from the input connector to link other speakers with the same audio signal.
GND LIFT – This switch lifts the ground of the balanced audio inputs from the earth-ground of the amplifier module.
PRESET BUTTON – This button has two functions:

1. Pressing it while powering on the unit
   ID ASSIGN the internal DSP assigns a new ID to the unit for the PRONET remote control operation. Each loudspeaker must have a unique ID to be visible in the PRONET network. When you assign a new ID, all the other loudspeakers with the ID already assigned must be ON and connected to the network.

2. Pressing it with the unit ON you can select the DSP PRESET. The selected PRESET is indicated by the corresponding LED:
   2 x AX12C This PRESET allows to the connection of two AX12C column array elements to the POWER OUTPUT Speakon connector, see example. 4 x AX12C This PRESET allows to connection of four AX12C column array elements to the POWER OUTPUT Speakon connector, see an example. 1 x AX12C This PRESET allows the connection of one AX12C column array element to the POWER OUTPUT Speakon connector, see an example.

USER:  This LED lights when the USER PRESET is loaded. This preset corresponds to USER MEMORY no. 1 of the DSP and, as a factory setting, it’s the same to STANDARD. If you want to modify it, you have to connect the unit to a PC, edit the parameters with PRONET software, and save the PRESET into USER MEMORY no. 1.

• NETWORK IN/OUT – These are standard RJ45 CAT5 connectors (with optional NEUTRIK NE8MC RJ45 cable connector carrier), used for PRONET network transmission of remote control data over long distances or multiple unit applications.
• TERMINATE – In a PRONET network the last loudspeaker device must be terminated (with an inner load resistance), especially in a long run cabling: press this switch if you want to terminate the unit.
• POWER OUT – SW2100A can power the passive AX12C column array module (or other loudspeakers) through the available power output on the back panel.

WARNING: for optimal protection and equalization connect the exact number of AX12C modules specified by the selected PRESET.

POWER AMPLIFIERS
The SW2100A is powered by DA SERIES digital power modules, a new generation of CLASS D power amplifiers with digitally-controlled SMPS. The innovative technology used for these amplifiers (including also the use of a variable switching frequency) offers performances at the top of the range, such as a superior sound definition at any audio frequency, very high dynamics for low- level signals, and very low distortion even at the maximum power. The superior sound quality can be compared with top-of-the-range AB-class analog systems, while the DA modules feature higher dynamics, very compact size and lightweight, and efficiency above 90%. The DA module employed for powering the SW2100A features also PFC (Power Factor Correction), a technology able to guarantee always the highest level of power regardless of any eventual fluctuations of the power supply. It delivers in an ultra-compact package 2000W (@ 4 ohms) from each of its two channels: one channel is used to drive the 21” woofer, and the other, through an output SPEAKON connector, can power AX12C line array modules or other loudspeakers.

SIGNAL PROCESSING
The system processing is based on the CORE DSP platform, which has been designed by the PROEL R&D Laboratories using one of the most advanced SHARC DSP for audio applications. It features 40bit, 96kHz floating point resolution, and high-quality 24bit AD/DA converters, for perfect signal integrity, a dynamic range over 110dB, and superior sonic performance. Thanks to its massive processing power, the CORE platform is capable of providing the most sophisticated algorithms for speaker processing, together with remote control and networking capability.
The PRONET control software, working on a solid and reliable CANBUS-based network protocol, provides an intuitive interface for the remote control of the whole system, with the possibility of eqing, delaying, increasing the protections, and monitoring the status of the amplifier.

PRONET AX

• PRONET AX software has been developed in collaboration with sound engineers and sound designers, to offer an “easy-to-use” tool to set up and manage your audio system. With PRONET AX you can visualize signal levels, monitor internal status, and edit all the parameters of each connected device.
• You can download the PRONET AX app from the AXIOM website at http://www.axiomproaudio.com/.

The AXIOM active loudspeaker devices can be connected to a network and controlled by the PRONET AX software, for the network connection the PROEL USB2CAN (with 1-port) or the USB2CAN-D (with 2-port) converter optional accessory is needed.

PRONET AX network is based on a “bus-topology” connection, where the first device is connected to the network input connector of the second device, the second device’s network output is connected to the network input connector of the third device, and so on. To ensure reliable communication the first and the last device of the “bus-topology” connection must be terminated. This can be done by pressing the “TERMINATE” switch near the network connectors in the rear panel of the first and last device. For the network connections simple RJ45 cat.5 or cat.6 ethernet cables can be used (please don’t confuse an ethernet network with a PRONET AX network these are completely different and must be fully separated also both use the same kind of cable).
Assign the ID number

To work properly in a PRONET AX network each connected device must have a unique identifier number, called ID. By default the USB2CAN-D PC controller has ID=0 and there can be only one PC controller. Every other device connected must have its unique ID equal to or greater than 1: in the network, two devices with the same ID.

To correctly assign a new available ID to each device for working properly in a Pronet AX network, follow these instructions:

1. Switch off all the devices.
2. Connect them correctly to the network cables.
3. “TERMINATE” the end device in the network connection.
4. Switch on the first device and keep pressing the “PRESET” button on the control panel.
5. Leaving the previous device switched on, repeat the previous operation on the next device until the latest device is turned on.

The “Assign ID” procedure for a device makes the internal network controller perform two operations: reset the current ID; and search the first free ID in the network, starting from ID=1. If no other devices are connected (and powered on), the controller assumes ID=1, which is the first free ID, otherwise, it searches for the next one left free.

These operations ensure that every device has its unique ID, if you need to add a new device to the network you simply repeat the operation of step 4. Every device maintains its ID also when it is turned because the identifier is stored in the internal memory and it is cleared only by another “Assign ID” step, as explained above.

With the network made always of the same devices, the assigning ID procedure must be executed only the first time the system is turned on.
For more detailed instructions about PRONET see the PRONET AX USER’S MANUAL included with the software.

TOOLS
This is a list of tools that can be useful to set properly a vertical column array system or a complex point source system.

CABLE TESTER
It is a good practice to check all cables before each installation because even one faulty cable can compromise heavily the system performance.

INCLINOMETER WITH LEVER
This tool can be used to verify the vertical array angle. It can be used at the top or at the bottom of the array In this case you have to sum all splay angles, so the maximum precision is needed for aiming the vertical array, particularly for long throw applications.

LASER DISTANCE METER
This instrument can be useful to measure the height of the vertical array and to know the distance between FOH-Subs and FOH-Array for setting the delay time.

ACOUSTIC MEASUREMENT SYSTEM (SMAART, SATlive, or similar)
These are useful for measuring delays, phases,s and responses of the system.

WARNING! CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITIONS OF USE:

• SW2100A is NOT designed to be suspended, use it in the ground stack only.
• This loudspeaker is designed exclusively for Professional audio applications. The product must be installed by qualified personal only.
• Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideration all current National, Federal, State and Local regulations. Please contact the manufacturer for further information.
• Proel does not accept any liability for damage caused to third parties due to improper installation, lack of maintenance, tampering or improper use of this product, including disregard of acceptable and applicable safety standards.
• During assembly pay attention to the possible risk of crushing. Wear suitable protective clothing. Observe all instructions given on the rigging components and the loudspeaker cabinets. When chain hoists are in operation ensure that there is nobody directly underneath or in the vicinity of the load. Do not under any circumstances climb on the array.

BASIC INSTALLATION INSTRUCTIONS

Stacked installation of AX12C using SW2100A subwoofer as base

WARNING

• The ground where the SW2100A is placed needs to be stable and compact.
• Adjust the feet to lie the SW2100A perfectly horizontal to the ground. Use a spirit level to obtain the best result.
• Always secure ground-stacked setups against movement and possible tipping over.
• A maximum of 2 x AX12C speakers are allowed to be installed over a SW2100A serving as ground support. Other installation examples are explained in the AX12C user manual.

Pin locking and splay angles set up
The figure below shows how to insert correctly the locking pin and how to set up the splay angle between loudspeakers.

LOCKING PIN INSERTION

TWO AX12C STACKED ON A SW2100A

SW2100A + AX12C connection examples

WARRANTY

LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operation of this product for two years from the original date of purchase. If any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period, the owner should inform about these defects the dealer or the distributor, providing a receipt or invoice of the date of purchase and defect detailed description. This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and the warranty is still valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defectiveness.

• This unit package has been submitted to ISTA 1A integrity tests. We suggest you control the unit conditions immediately after unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspection.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex-warehouse” and shipment is at the charge and risk of the buyer.
• Possible damages to the unit should be immediately notified to the forwarder. Each complaint for package tampered with should be done within eight days from product receipt.

SAFETY INSTRUCTIONS

• To reduce the risk, close supervision is necessary when the product is used near children.
• Protect the apparatus from atmospheric agents and keep it away from water, rain, and high-humidity places.
• This product should be site away from heat sources such as radiators, lamps, and any other device that generates heat.
• This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation.
• Care should be taken so that objects and liquids do not go inside the product.
• The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the product. Connect the apparatus to a power supply using only power cord included making always sure it is in good condition.
• WARNING: The mains plug is used as a disconnect device, the disconnect device shall remain readily operable.
• Do not cancel the safety feature assured through a polarized line plug (one blade wider than the other) or with an earth connection.
• Make sure that the power supply mains line has a proper earth connection.
• The power supply cord should be unplugged from the outlet during strong thunderstorms or when left unused for a long time.

CE CONFORMITY
Proel products comply with directive 2014/30/UE (EMC), as stated in EN 55103-1 and EN 55103-2 standards, and with directive 2014/35/UE (LVD), as stated in EN 60065 standard.
PROEL S.p.A. (World Headquarter) – Via alla Ruenia 37/43 – 64027 Sant’Omero (Te) – ITALY

• Tel: +39 0861 81241
• Fax: +39 0861 887862
• www.axiomproaudio.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>