PROEL J-WASH 400 LED Wash Moving Head User Manual

: May 15, 2024
: Proel

Table of Contents

Product Usage Instructions
INTRODUCTION
SAFETY INSTRUCTIONS
OPENING AND CONTROL
REARVIEW
INSTALLATION AND SWITCH ON
SETUP
MAINTENANCE
TECHNICAL SPECIFICATIONS
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROEL J-WASH 400 LED Wash Moving Head

PROEL-J-WASH-400-LED-Wash-Moving -Head-fig-10

Product Usage Instructions

Safety Instructions

Anyone involved in the installation and maintenance of the device must:

Be qualified
Follow the instructions in this manual in theaters, halls, event venues, etc.

Opening and Control

Ensure all parts for fixing the product are in good condition. Verify the stability of the anchorage point before positioning the product. Securely attach the safety cable to the device and fix it to the supporting structure to minimize falls in case of primary support system failure. Replace the safety cable with an original spare if worn.

Setup

Place the projector so that objects hit by the light beam are at least 2 meters away from the projector’s lenses.
Position the product so that any flammable material is at least 0.50 meters away from any point on the device’s surface. Do not place filters or other materials on the lenses or optical axis.
Suitable for mounting on surfaces with normal fire-resistant
and/or flammable characteristics.

Maintenance

Before performing any maintenance operation or cleaning the product, disconnect the power supply and unplug the cable from the device. After turning off, do not remove any part of the device for at least 35 minutes to avoid the risk of burns. Damaged lenses must be replaced with original spares.

INTRODUCTION

Thank You for choosing one of Our products.
Please refer to the instructions and warnings contained in this user manual, please retain it for future reference.
This manual contains information about the installation and use of the device.
The information contained in this publication has been carefully prepared and checked. However, it does not assume any responsibility for any inaccuracies. All rights are reserved and this document can not be copied, photocopied, or reproduced in whole or in part without previous written permission of PROEL. PROEL reserves the right to make, without notice, any aesthetical, functional, or design changes or modifications in every one of its products. PROEL doesn’t assume any responsibility for the use or application of the products here described.

The crossed bin symbol, shown on the product or on accompanying documents, indicates that the product should not be disposed of with other household waste at the end of the lifecycle. To avoid any damage to the environment, the user is encouraged to separate this product from other kinds of waste and recycle it responsibly to promote the sustainable reuse of material resources. Home users are encouraged to contact the retailer where they purchased this product or their local government office for details on the separate collection and recycling of this type of product. Business users are encouraged to contact their suppliers and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste.

The lightning symbol with an arrow in an equilateral triangle intends to alert the user to the presence of not insulated “dangerous voltages” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point symbol within an equilateral triangle intends to alert the user to the presence of important instructions for use and maintenance on the accompanying documents of the product.
The “F” inside an equilateral reversed triangle means that the product is suitable for mounting on normally flammable surfaces.
The product to which this manual refers complies with the European Directives pursuant to the safety of electrical equipment supplied at low voltage (LVD) and to the Electromagnetic Compatibility (EMC)

SAFETY INSTRUCTIONS

Caution! This product is not suitable for household illumination.
Please read this manual before installing and applying power to the equipment, follow the safety precautions listed below, and observe all warnings in this manual and printed on. Please contact a PROEL distributor for assistance with any questions about how to activate the equipment safely. Contact a qualified technician for any maintenance work not described in this manual.
Do not modify the fixture or install accessories and upgrade kits that are not the Proel original ones.
People involved in the installation and maintenance of the device must:

Be qualified
Follow the instructions of this manual in the theaters, in the halls, in the places where the events take place, etc.

CHECKS BEFORE INSTALLATION
Make sure all the parts for fixing the product are in good condition.
Make sure that the anchor point is stable before positioning the product.
The safety cable must be properly attached to the device and fixed to the supporting structure so that, in case of failure of the primary supporting system, it has the lowest possible fall of the device.
If the safety cable wears, must be replaced with an original spare.

MINIMUM DISTANCE OF ILLUMINATED OBJECTS
The projector must be positioned so that the objects hit by the beam of light are at least 2 meters from the lens of the projector.

MINIMUM DISTANCE FROM FLAMMABLE MATERIALS
The product must be positioned so that any flammable material is at least 0.50 meters from any point on the surface of the device. Never place filters or other materials over the lens or on the optical axis.

MOUNTING SURFACES
The device is suitable for mounting on normally flammable surfaces.

REFERENCE TEMPERATURE
The ambient temperature range of use of the device varies between + 5 ° C (min) and + 40 ° C (max), outside of that range the device should not be used.
The maximum temperature of the housing Tb = 80 ° C must never be exceeded. Do not block the exhaust fans, ensuring a minimum clearance of 0.5 meters around the ventilation holes.

IP20 PROTECTION RATING
The device is protected against the penetration of solid bodies larger than 12 mm (0,47 “) in diameter (first digit 2), but not against dripping water, rain, splashes, or jets of water (second digit 0). Use only in dry areas. Inside use only. Do not expose the equipment to rain or moisture.

PROTECTION AGAIN ELECTRIC SHOCK
The device must be connected to a power supply system with efficient earthing. Moreover, it is recommended to protect the power supply lines of the product from indirect contact and/or shorting to earth by using an appropriately sized anti-electrical shock switch.

CONNECTION TO THE MAINS
The electrical connection must be carried out by a qualified electrician.
Ensure that the mains frequency and voltage correspond to those for which the equipment is designed, as shown in the electrical data label. This label also shows the power consumption that is necessary to refer to evaluate the maximum number of devices to be connected to the electricity line, in order to avoid power overloading.
If the external power cord of this light is damaged, it must be replaced with a special cord exclusively available from Your PROEL dealer.
Never operate the equipment with lenses and/or covers missing or damaged.
In case of non-use, it is recommended to unplug the projector from the mains.

MAINTENANCE
Before starting any maintenance or cleaning of the product, disconnect the power from the mains and disconnect the power cable from the device. After switching off, do not remove any part of the device for at least 35 minutes to avoid the risk of burns. The lenses, if damaged, must be replaced with original spare parts.

WARNING
CAUTION. Do not look directly at the light source. Do not look at the beam with lenses, glasses, mirrors or similar optical instruments that could change the convergence of light, causing serious damage to people and / or things.

OPENING AND CONTROL

Carefully open the package, check the content, and make sure that all the parts are present and are in good condition. In cases where some parts are not present or are damaged, immediately contact Your supplier and retain the packaging for verification.

WARNING
If the product has been exposed to drastic temperature changes, let the unit be turned off until it reaches room temperature because the presence of condensation can damage the product if it is turned on.

Verify that the box contains the following items:

N° 1 SG JBEAM230
N° 2 Omega holders
N° 1 Power cord
N° 1 User Manual

FRONT VIEW

Lenses
Display + buttons
Strip LED RGB

REARVIEW

Dmx OUT
Dmx IN
Power OUT
Power IN
Switch ON/OFF
Fuse
USB connector for wireless
(SG WECONUSB sold separately)

INSTALLATION AND SWITCH ON

PRODUCT INSTALLATION

Do not shake the device. Avoid the use of too much force during installation or unit fixing.
The unit can be installed on the floor resting on the rubber feet, or suspended on a truss.

WARNING

IT’S REQUIRED the mounting of the safety rope (PLH232 – PLH248) sold separately) in the case where the product is hung on a wall, ceiling, or a truss. Except when the device is placed on the floor, the safety cable is always required.

CONNECTION TO THE MAINS

The device must be connected to a power supply system with a proper earth system. Moreover, it is recommended to protect the power supply lines of the products from indirect contact and/or shorting to earth by using an appropriately sized anti-electrical shock switch. The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the device is designed, as shown in the electrical data label. PROEL-J-WASH-400-LED-Wash-Moving -Head-
fig-4

CONNECTION TO THE DMX CHAIN

Use a cable conforming to specifications EIA RS-485: pole twisted, shielded, 120Ohm characteristic impedance and low capacity (SAGITTER SG DMX3 – SG DMX5).
Do not use a microphone cable or other cable with different characteristics than those specified. Terminations must be made with male/female XLR 3-pin connectors. You must enter on the last device a terminal plug with a 120Ohm resistance (min1 / 4 W) between terminals 2 and 3. IMPORTANT: The cables must not come into contact with each other or with the metal housing of the connectors. The housing itself must be connected to the shield braid and to pin 1 of the connectors. PROEL-J-WASH-400-LED-Wash-Moving -Head-
fig-5

SETUP

MENU

PROEL-J-WASH-400-LED-Wash-Moving -Head-fig-5

MASTER/SLAVE MODE
In this mode, more units can be linked together as a single chain and work in a synchronized way.

Use a DMX cable to link together all the units from the connector DMX OUT to DMX IN.
Define the first unit of the chain as MASTER, all other units will be SLAVE and they must be set DMX = 001.
Operate the Master unit in Automatic mode or Musical to operate the entire system. The entire chain of Slave units will act as the Master unit.

DMX MODE

PROEL-J-WASH-400-LED-Wash-Moving -Head-fig-7

MAINTENANCE

To ensure optimal performance, the unit must be frequently cleaned. Unplug the device from the mains and let it cool for at least 35 minutes to avoid the risk of burns. Use a vacuum cleaner or an air compressor and a soft brush or a lens cloth to remove the dust deposited.
The lenses, like any other damaged part, must be replaced with original spare parts.