Proel ED25P Passive Near Field Point Source Loud Speaker User Manual
- May 15, 2024
- Proel
Table of Contents
Proel ED25P Passive Near Field Point Source Loud Speaker User Manual
Watch for these symbols:
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure, that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. -
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally, or has been dropped. -
Warning: to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
-
Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.
-
To completely disconnect this apparatus from the ac mains, disconnect the power supply cord plug from the ac receptacle.
-
The mains plug of the power supply cord shall remain readily operable.
-
This apparatus contains potentially lethal voltages. To prevent electric shock or hazard, do not remove the chassis, input module or ac input covers. No user serviceable parts inside. Refer servicing to qualified service personnel.
-
The loudspeakers covered by this manual are not intended for high moisture outdoor environments. Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts. Avoid exposing the speakers to
direct moisture. -
Keep loudspeakers out of extended or intense direct sunlight. The driver suspension will prematurely dry out and finished surfaces may be degraded by long-term exposure to intense ultra-violet (UV) light.
-
The loudspeakers can generate considerable energy. When placed on a slippery surface such as polished wood or linoleum, the speaker may move due to its acoustical energy output.
-
Precautions should be taken to assure that the speaker does not fall off a stage or table on which it is placed.
-
The loudspeakers are easily capable of generating sound pressure levels (SPL) sufficient to cause permanent hearing damage to performers, production crew and audience members. Caution should be taken to avoid prolonged exposure to SPL in excess of 90 dB.
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
DECLARATION OF CONFORMITY
The product is in compliance with:
RoHS Directive 2011/65/EU and 2015/863/EU, WEEE Directive 2012/19/EU.
The product is in compliance with:
S.I. 2012/3032 The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operation of this product
for a period of two years from the original date of purchase. If any defects
are found in the materials or workmanship or if the product fails to function
properly during the applicable warranty period, the owner should inform about
these defects the dealer or the distributor, providing receipt or invoice of
date of purchase and defect detailed description.
This warranty does not extend to damage resulting from improper installation,
misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units,
and when the unit has been properly used and warranty is still valid, then the
unit will be replaced or repaired. Proel S.p.A. is not responsible for any
“direct damage” or “indirect damage” caused by product defectiveness.
- This unit package has been submitted to ISTA 1A integrity tests. We suggest you control the unit conditions immediately after unpacking it.
- If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspection.
- Proel is not responsible for any damage that occurs during shipment.
- Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
- Possible damages to unit should be immediately notified to forwarder. Each complaint for package tampered with should be done within eight days from product receipt.
CONDITIONS OF USE
Proel do not accept any liability for damage caused to third parties due to
improper installation, use of non-original spare parts, lack of maintenance,
tampering or improper use of this product, including disregard of acceptable
and applicable safety standards. Proel strongly recommends that this
loudspeaker cabinet be suspended taking into consideration all current
National, Federal, State and Local regulations. The product must be installed
be qualified personal. Please contact the manufacturer for further
information.
INTRODUCTION
The ED25P is an ultra-compact and lightweight, two-way passive point source
loudspeaker designed for near-field sound reinforcement applications such as
television, stage front, conferencing, theatres, and audio-visual. Due to its
very low profile, the
ED25P is an ideal stage lip monitor and is especially useful for fashion show
catwalks where it can provide unobtrusive inwards/ outwards coverage for both
audience and presenters.
The two 5.25” low frequency drivers are matched to a dome tweeter on a
spherical waveguide horn with an audiophile-grade passive crossover in a WTW
linear enclosure configuration to give a wide dispersion pattern that allows
widely spaced units to cover large spaces with high quality background sound.
The cabinet is trapezoidally shaped, and also asymmetrical, and this profile
not only allows the assembly of small clusters using the integral flypoints,
but also enables it to be suspended horizontally very close to a ceiling or
placed on a stage front as a low profile
monitor.
The 15mm birch plywood cabinet is provided with M8 rigging points on the top
and bottom, and M10 and M5 rigging points on the rear of the cabinet to allow
suspension in fixed installations using optional mounting brackets. Two
Neutrik® speakON™ NL4
connectors provide input and link connections.
To extend the system’s low frequency response the ED25P can be complemented by
subwoofers from the Axiom SW series such as the SW210P or SW18P.
TECHNICAL SPECIFICATION
MECHANICAL DRAWING
OPTIONAL ACCESSORIES
see http://www.axiomproaudio.com for detailed description and other available accessories.
SPARE PARTS
NL4MP Neutrik Speakon® panel socket 98ALT200001 5.25’’ woofer – 1.5” VC – 8
ohm
91CRO039AR1 ED23P/ED25P Crossover PCBA 98DRI025C 1’’ HF driver – 1” VC – 8 ohm
with Wave Guide
INPUT
LINK
Power output in parallel with the INPUT socket, for connecting the unit to
another speaker. The number of ED25P cabinets that can be connected in
parallel depends on the amplifier load capacity.
Note: there is no silk-screen printing on the speaker, the illustration above
is only representative of the internal connection, both speakon connectors on
the sides of the speaker can be used as INPUT or LINK.
KPTLTP WALL MOUNTING
This wall mounting bracket allows to aim the loudspeaker in both horizontally
and vertically. The horizontal aiming is free with +/- 15° and the vertical
aiming is in 4 steps (0°,-15°,-30°,-45°).
Note: the speaker plate can be rotated as shown above for the optimal speaker
orientation, the speaker plate will be fixed to the rear M5 flying points.
KPTED25B WALL or TRUSS MOUNTING
Using the “C” shape bracket the ED25P loudspeaker can be installed to walls or
mounted to trusses in combination combining with a M12 ALISCAF (not supplied).
It allows to aim the speaker in one direction, vertical or horizontal.
WARNING! CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE:
- For a supplementary safety assure always the loudspeaker to the wall with an alternative rope.
- This loudspeaker is designed exclusively for Professional audio applications. The product must be installed by qualified personal only.
- Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideration all current National, Federal, State and Local regulations. Please contact the manufacturer for further information.
- Proel do not accept any liability for damage caused to third parties due to improper installation, lack of maintenance, tampering or improper use of this product, including disregard of acceptable and applicable safety standards.
- During assembly pay attention to the possible risk of crushing. Wear suitable protective clothing. Observe all instructions given on the rigging components and the loudspeaker cabinets. When chain hoists are in operation ensure that there is nobody directly underneath or in the vicinity of the load. Do not under any circumstances climb on the array.
PROEL S.p.A. (World Headquarters) – Via alla Ruenia 37/43 – 64027 Sant’Omero
(Te) – ITALY
Tel: +39 0861 81241 Fax: +39 0861 887862
www.axiomproaudio.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>