PROEL J-BEAM 150 LED Beam Moving Head User Manual

: May 15, 2024
: Proel

Table of Contents

PROEL J-BEAM 150 LED Beam Moving Head
Product Information
Product Usage Instructions
INTRODUCTION
SAFETY INSTRUCTIONS
OPENING AND CONTROL
FRONTALE VIEW
REAR VIEW
INSTALLATION AND SWITCH ON
SETUP
TECHNICAL SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROEL J-BEAM 150 LED Beam Moving Head

Product Information

Specifications

Model: [Insert Model]
Class: [Insert Class]
Protection Class: IP20
Power Supply: [Insert Voltage]
Mounting Surfaces: Suitable for normal and/or flammable surfaces

Product Usage Instructions

Safety Instructions
Anyone involved in the installation and maintenance of the device must be qualified and follow the instructions provided in the manual.

Installation and Setup

Ensure all parts for fixing the product are in good condition.
Verify the stability of the anchoring point before positioning the product.
Securely attach the safety cable to the device and fix it to the support structure.
Position the projector so that illuminated objects are at least 2 meters away from the projector lens.
Avoid placing any flammable materials within 0.50 meters of any part of the product.
Mount on surfaces with normal or flammable characteristics.

Maintenance
Before performing any maintenance or cleaning, disconnect the power supply and unplug the device. Wait at least 35 minutes after turning off before handling any parts to avoid burns. Damaged lenses should be replaced with original parts.

FAQ

Q: How often should I replace the safety cable?
A: The safety cable should be inspected regularly and replaced with an original spare if any signs of wear are present.
Q: Can I mount the product on any surface?
A: The product is suitable for mounting on surfaces with normal or flammable characteristics, ensuring proper stability and safety measures are followed.

INTRODUCTION

Thank You for choosing one of Our products!
Please refer to the instructions and warnings contained in this user manual, please retain it for future reference. This manual contains information about the installation and use of the device. The information contained in this publication has been carefully prepared and checked. However it is not assumed any responsibility for any inaccuracies. All rights are reserved and this document can not be copied, photocopied, reproduced in whole or in part without previous written permission of PROEL. PROEL reserves the right to make, without notice, any aesthetical, functional or design changes or modifications in everyone of its products. PROEL doesn’t assume any responsibility for the use or application of the products here described.
****The crossed bin symbol, shown on the product or on accompanying documents, indicates that the product should not be disposed with other household waste at the end of the lifecycle. To avoid any damage to the environment, the user is encouraged to separate this product from other kinds of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Home users are encouraged to contact the retailer where they purchased this product or their local government office for details on separate collection and recycling this type of product. Business users are encouraged to contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial waste.
The lightning symbol with arrow in an equilateral triangle intends to alert the user to the presence of not insulated “dangerous voltages” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point symbol within an equilateral triangle intends to alert the user to the presence of important instructions for use and maintenance on the accompanying documents of the product.
The “F” inside an equilateral reversed triangle means that the product is suitable for mounting on normally flammable surfaces.
The product to which this manual refers comply with the European Directives pursuant to the safety of electrical equipment supplied at low voltage (LVD) and to the Electromagnetic Compatibility (EMC)

SAFETY INSTRUCTIONS

Caution! This product is not suitable for household illumination.
Please read this manual before installing and applying power to the equipment, follow the safety precautions listed below and observe all warnings in this manual and printed on. Please contact a PROEL distributor for assistance with any questions about how to activate the equipment safely. Contact a qualified technician for any maintenance work not described in this manual. Do not modify the fixture or install accessories and upgrade kits that are not the Proel original ones.

People involved in the installation and maintenance of the device must:

Be qualified
Follow the instructions of this manual in the theaters, in the halls, in the places where the events take place, etc.

CHECKS BEFORE INSTALLATION
Make sure all the parts for fixing the product are in good condition. Make sure that the anchor point is stable before positioning the product. The safety cable must be properly attached to the device and fixed to the supporting structure so that, in case of failure of the primary supporting system, it has the lowest possible fall of the device. If the safety cable wear, must be replaced with an original spare.

MINIMUM DISTANCE OF ILLUMINATED OBJECTS
The projector must be positioned so that the objects hit by the beam of light are at least 2 meters from the lens of the projector.

MINIMUM DISTANCE FROM FLAMMABLE MATERIALS
The product must be positioned so that any flammable material is at least 0.50 meters from any point of the surface of the device. Never place filters or other materials over the lens or on the optical axis.

MOUNTING SURFACES
The device is suitable for mounting on normally flammable surfaces.

REFERENCE TEMPERATURE
The ambient temperature range of use of the device varies between + 5 ° C (min) and + 40 ° C (max), outside of that range the device should not be used. The maximum temperature of the housing Tb = 80 ° C must never be exceeded. Do not block the exhaust fans, ensuring a minimum clearance of 0.5 meters around the ventilation holes.

IP20 PROTECTION RATING
The device is protected against the penetration of solid bodies larger than 12 mm (0,47 “) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0). Use only in dry areas. Inside use only. Do not expose the equipment to rain or moisture.

PROTECTION AGAIN ELECTRIC SHOCK
The device must be connected to a power supply system with efficient earthing. Moreover, it is recommended to protect power supply lines of the product from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch.

CONNECTION TO THE MAINS
The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the equipment is designed, as shown in the electrical data label. This label also shows the power consumption that is necessary to refer to evaluate the maximum number of devices to be connected to the electricity line, in order to avoid power overloading. If the external power cord of this light is damaged, it must be replaced with a special cord exclusively available from Your PROEL dealer. Never operate the equipment with lenses and / or covers missing or damaged. In case of non-use, it is recommended to unplug the projector from the mains.

MAINTENANCE
Before starting any maintenance or cleaning the product, disconnect the power from the mains and disconnect the power cable from the device. After switching off, do not remove any part of the device for at least 35 minutes to avoid the risk of burns. The lenses, if damaged, must be replaced with original spare parts.

WARNING
CAUTION. Do not look directly at the light source. Do not look at the beam with lenses, glasses, mirrors or similar optical instruments that could change the convergence of light, causing serious damage to people and / or things.
WARNING! DANGER FOR THE EYES! Do not look directly at the light source

OPENING AND CONTROL

Carefully open the package, check the content and make sure that all the parts are present and are in good condition. In cases where some parts are not present or are damaged, immediately contact Your supplier and retain the packaging for verification.

WARNING!
If the product has been exposed to drastic temperature changes, let the unit turned off until it reaches room temperature because the presence of condensation can damage the product if it is turned on.

Verify that the box contains the following items:

N° 1 SG JBEAM150
N° 1 Omega holder
N° 1 Power chord
N° 1 User manual

FRONTALE VIEW

Lens
Display + buttons

REAR VIEW

Dmx IN
Dmx OUT
Power OUT
Power IN
Fuse
USB connector for wireless (SG WECONUSB sold separately)

INSTALLATION AND SWITCH ON

PRODUCT INSTALLATION

Do not shake the device. Avoid the use of too much force during installation or unit fixing.
The unit can be installed on the floor resting on the rubber feet, or suspended on a truss.

WARNING! IT’S REQUIRED
the mounting of the safety rope (PLH232 – PLH248) sold separately) in the case where the product is hung on a wall, ceiling or on a truss. Except when the device is placed in the floor, the safety cable is always required.

CONNECTION TO THE MAINS

$PROEL-J-BEAM-150-LED-Beam-Moving-Head-$9$$

The device must be connected to a power supply system with a proper earth system. Moreover, it is recommended to protect power supply lines of the products from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch. The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the device is designed, as shown in the electrical data label.

CONNECTION TO THE DMX CHAIN

$PROEL-J-BEAM-150-LED-Beam-Moving-Head-$10$$

Use a cable conforming to specifications EIA RS-485: pole twisted, shielded, 120Ohm characteristic impedance and low capacity (SAGITTER SG DMX3 – SG DMX5).
Do not use microphone cable or other cable with different characteristics than those specified. Terminations must be made with male / female XLR 3-pin connectors. You must enter on the last device a terminal plug with a 120Ohm resistance (min1 / 4 W) between terminals 2 and 3. IMPORTANT: The cables must not come into contact with each other or with the metal housing of the connectors. The housing itself must be connected to the shield braid and to pin 1 of the connectors.

SETUP

MENU
Highlighted the default values

Level 1	Level 2	Level 3	Level 4	Description
DMX	Dmx Address	001 – 512		DMX address
Channel Mode	10CH		Channels mode
12CH
Auto Run	Program 1…9	Master	Auto mode master
Alone	Auto mode alone
Music Run	Program 1…9	Master	Sound mode master
Alone	Sound mode alone

SET

MASTER/SLAVE MODE
In this mode, more units can be linked together as a single chain and work in a synchronized way.

Use a DMX cable to link together all the units from the connector DMX OUT to DMX IN.
Define the first unit of the chain as MASTER, all other units will be SLAVE and they must be set DMX = 001.
Operate the Master unit in Automatic mode or Musical to operate the entire system. The entire chain of Slave unit will act as the Master unit.

DMX MODE

CH MODE| Function| Values| Description|
---|---|---|---|---
10 CH| 12 CH| | | |
1| 1| Pan| 000 – 255| Pan movement|
| 2| Pan fine| 000 – 255| Pan fine movement|
2| 3| Tilt| 000 – 255| Tilt movement|
| 4| Tilt fine| 000 – 255| Tilt fine movement|
| | | 000 – 003| Open|
| | | 004 – 007| Half color Open / Red|
| | | 008 – 011| Red|
| | | 012 – 015| Half color Red / Blue|
| | | 016 – 019| Blue|
| | | 020 – 023| Half color Blue / Green|
| | | 024 – 027| Green|
| | | 028 – 031| Half color Green / Yellow|
| | | 032 – 035| Yellow|
| | | 036 – 039| Half color Yellow / Magenta|
| | | 040 – 043| Magenta|
| | | 044 – 047| Half color Magenta / CTB|
| | | 048 – 051| CTB|
| | Color wheel (half| 052 – 055| Half color CTB / Violet|
056 – 059| Violet|
| | color = ON)|
060 – 063| Half color Violet / Orange|
3| 5| For the option| 064 – 067| Orange|
| | Half color = OFF| 068 – 071| Half color Orange / Dark green|
| | please see next| 072 – 075| Dark green|
| | table| 076 – 079| Half color Dark green / Pink|
| | | 080 – 083| Pink|
| | | 084 – 087| Half color Pink / Orange 2|
| | | 088 – 091| Orange 2|
| | | 092 – 095| Half color Orange 2 / Cyan|
| | | 096 – 099| Cyan|
| | | 100 – 103| Half color Cyan / Light yellow|
| | | 104 – 107| Light yellow|
| | | 108 – 111| Half color Light yellow / UV|
| | | 112 – 115| UV|
| | | 116 – 127| Half color UV / Open|
| | | 128 – 189| Clockwise rotation from fast to slow|
| | | 190 – 193| Stop|
| | | 194 – 255| Counterclockwise rotation from slow to fast|
4| 6| Gobo wheel| 000 – 004| Open|
005 – 009| Gobo 1|
010 – 014| Gobo 2|
015 – 019| Gobo 3|
020 – 024| Gobo 4|
025 – 029| Gobo 5|
030 – 034| Gobo 6|
035 – 039| Gobo 7|
040 – 044| Gobo 8|
045 – 049| Gobo 9|
| | | 050 – 054| Gobo 10
---|---|---|---|---
055 – 059| Gobo 11
060 – 064| Gobo 12
065 – 069| Gobo 13
070 – 074| Gobo 14
075 – 079| Gobo 15
080 – 084| Gobo 16
085 – 089| Gobo 17
090 – 097| Gobo 1 shake from slow to fast
098 – 105| Gobo 2 shake from slow to fast
106 – 113| Gobo 3 shake from slow to fast
114 – 121| Gobo 4 shake from slow to fast
122 – 129| Gobo 5 shake from slow to fast
130 – 137| Gobo 6 shake from slow to fast
138 – 145| Gobo 7 shake from slow to fast
146 – 153| Gobo 8 shake from slow to fast
154 – 161| Gobo 9 shake from slow to fast
162 – 169| Gobo 10 shake from slow to fast
170 – 177| Gobo 11 shake from slow to fast
178 – 185| Gobo 12 shake from slow to fast
186 – 193| Gobo 13 shake from slow to fast
194 – 201| Gobo 14 shake from slow to fast
202 – 209| Gobo 15 shake from slow to fast
210 – 217| Gobo 16 shake from slow to fast
218 – 225| Gobo 17 shake from slow to fast
226 – 255| Forward rainbow effect from slow to fast
5| 7| Strobe| 000 – 031| Closed
032 – 063| Open
064 – 095| Strobe from slow to fast
096 – 127| Open
128 – 143| Pulse IN effect from slow to fast
144 – 159| Pulse OUT effect from fast to slow
160 – 191| Open
192 – 223| Random strobe from slow to fast
224 – 255| Open
6| 8| Dimmer| 000 – 255| Master dimmer from 0 – 100%
7| 9| Focus| 000 – 255| Focus from near to far
8| 10| Prism| 000 – 005| Prism OFF
006 – 127| Prism ON
128 – 189| Forward rotation from fast to slow
190 – 193| Rotation stop
194 – 255| Backward rotation from slow to fast
9| 11| Pan / Tilt speed| 000 – 225| Speed from max to min
226 – 235| Blackout by movement
236 – 245| Blackout by all wheels changing
246 – 255| No function
10| 12| Special functions| 000 – 019| No function
020 – 029| No function
030 – 039| No function
040 – 079| No function
080 – 084| Total reset
085 – 087| Pan / Tilt Reset
088 – 090| Color reset
| | | 091 – 093| Gobo reset
---|---|---|---|---
094 – 096| No function
097 – 099| Other motor reset
100 – 119| Internal program 1
120 – 139| Internal program 2
140 – 159| Internal program 3
160 – 179| Internal program 4
180 – 199| Internal program 5
200 – 219| Internal program 6
220 – 239| Internal program 7
240 – 255| Internal sound program 1
CH MODE| Function| Value| Description
---|---|---|---
10 CH| 12 CH
3| 5| Color wheel
(Half color = OFF)| 000 – 007| Open
008 – 015| Red
016 – 023| Blue
024 – 031| Green
032 – 039| Yellow
040 – 047| Magenta
048 – 055| CTB
056 – 063| Violet
064 – 071| Orange
072 – 079| Dark green
080 – 087| Pink
088 – 095| Orange 2
096 – 103| Cyan
104 – 111| Light yellow
112 – 127| UV
128 – 189| Clockwise rotation from fast to slow
190 – 193| Stop
194 – 255| Counterclockwise rotation from slow to fast

MAINTENANCE
To ensure optimal performance, the unit must be frequently cleaned. Unplug the device from the mains and let it cool for at least 35 minutes to avoid the risk of burns. Use a vacuum cleaner or an air compressor and a soft brush or a lens cloth to remove the dust deposited. The lenses, like any other damaged part, must be replaced with original spare parts.