Dryflow Slimforce Hand Dryer User Manual

: May 15, 2024
: Dryflow

Dryflow Slimforce Hand Dryer

Dryflow-Slimforce-Hand-Dryer-product

Specifications

Voltage: 220V-240V 50/60Hz, 4A/1000W
Stand-by Power: Less than 2.0W
Air Velocity: 100M/S [328 FT/S] / 360KM/H [224MPH]
Air Flow: 130M3/H [76.5CFM]
Drying Time: 10-12 Seconds
Timing Protection: Forced Hold-On 60 Seconds auto shut-off
Timing Duration: Auto Shut-Off 3 Seconds after last sensor read

Product Usage Instructions

Safety Warnings

Before installing or using the Slimforce Hand Dryer, ensure you have read and understood all safety information and warnings provided in the manual.

Installation must be carried out by qualified personnel in compliance with all regulations and laws.
Turn off the power at the main switch before installation or servicing.
Ensure the dryer is not installed on a flammable surface and electrical connections are not damaged.
Pre-arrange a suitable power outlet and grounding system in accordance with local regulations.
Do not install the dryer over a washbasin.
Children aged 8 years and above can use the dryer under supervision and appropriate training.
Avoid touching or covering the dryer during operation due to high temperatures near the air nozzle.

Installation Instructions

Refer to the mounting template provided in the packing list for proper positioning on the wall.
Use the wall anchors and screws provided to securely mount the hand dryer unit.
Ensure proper electrical wiring following safety guidelines and regulations.
Connect the dryer to a grounded power outlet.
Test the dryer to ensure it functions correctly before regular use.

Operation

To use the Slimforce Hand Dryer:

Place your hands under the air nozzle.
The dryer will automatically start blowing hot air.
Keep your hands in place until they are completely dry, typically within 10-12 seconds.
The dryer will auto shut-off after 3 seconds once it detects no more hand movement.

SAFETY WARNINGS

Before installing, be sure to read this installation manual and retain for future reference.
This product must be installed by qualified personnel in accordance with the instructions given in this manual and installation must comply with all applicable regulations, national security standards and laws in force in the country where the product is installed.
Turn off the power at the main switch before installing or servicing the dryer unit.
The dryer must not be installed on a flammable surface. Do not damage any parts of the electrical connections.
Pre-arrange an appropriate power outlet and a system of disconnection in accordance with current local regulations. Make sure the product is properly connected to ground. If there is no ground connection, there is a risk of an electrical shock.
Do not install the dryer over a washbasin. If the power cord is damaged, it must be repaired by qualified personnel to avoid any type of risk.
This dryer can be used by children aged 8 years and above. People with reduced physical, sensory or mental abilities or lack of experience and knowledge, if they have been given supervision and appropriate training regarding the use of the dryer in a safe manner, can use it with no restriction. Children should not play with the apparatus. Cleaning and
maintenance performed by the owner should not be done without children having supervision.
During use, temperatures above 158℉ [70℃] may develop in the parts near the hot air nozzle. Do not touch or cover the dryer during use or when finished using it.

General safety information

WARNING
This product is intended for installation by a qualified service person. Use AWG NO.12 solid conductor for wiring.
Disconnect power at the service breaker before installing or servicing.
All units must service breaker before installing or servicing. The ground wire must be connected to the dryer’s backplate.
DANGER
Failure to properly ground unit could result in service electrical shock and/or death.

PACKING LIST

Dryflow-Slimforce-Hand-Dryer-fig-1

SPECIFICATION

Voltage: 220V-240V 50/60Hz,4A/1000W
Stand-by Power: Less than 2.0W
Air Temperature: 4 0 ℃[104°F](Distance from nozzle=100MM[4″],Room Temp.=25℃[77°F])
Air Velocity: 1 0 0M/S[328 FT/S] / 360KM/H[224MPH]
Air Flow: 1 3 0M3/H[76.5CFM]
Drying Time: 1 0 -12 Seconds
Timing Protection: Forced Hold-On 60 Seconds auto shut-off
Timing Duration: Auto Shut-Off ≤3 Seconds after last sensor read
Sensor Range: 5-15CM[2″~ 5-7/8″], Owner Adjustable
Fuse Protection: 1kW,Main PCB, Φ5×20, 250V, 6A[230V]
Protection Level: IP23
Electric Isolation: CLASS ǀ (Metal cover)
Brush Motor: 30000RPM, 600W[0.8HP]
Noise [at 1M]: 74dB
Weight : 2.5KG[5.5lb]/Net Weight / 3.0KG[6.6lb]/Shipping Weight

BEFORE INSTALLATION

Installation must be carried out in accordance with the current edition of the local wiring regulations code having jurisdiction. Installation should be performed only by a qualified electrician.

Dryflow-Slimforce-Hand-Dryer-fig-2

INSTALLATION

Be sure to turn off the electric supply before any operation.
Place template against wall at desired height (see mounting height recommendations) and mark locations of 4 mounting holes Dia. 8mm(5/16″).
Remove hand dryer back transportation only purpose screw.
Remove and retain 2 side security hex cover screws and cover.
Mount the hand dryer base on the wall.
If the hand dryer is supplied in hardwired:
a. Connect the live wire(Coloured Brown, Red, or Black) to the terminal block marked “L”.
b. Connect the neutral wire(Coloured Black, Blue) to the terminal block marked “N”.
c. Connect the ground wire(Coloured Green or Yellow) to the terminal block marked “E”.
Before replacing cover, there is a customized option to run the dryer heater on (1000W) or heater off(600W).The switch is clearly marked.
Default setting is 12-15CM from nozzle. If it needs and please adjust its range.
Replace cover. Do not over-tighten screws.

OPERATION

No-touch operation.
There is a blue LED light to guide user to the air flow. Shake excess water from hands.
Place hands under the outlet to start operation. Rub hands lightly and rapidly.
Stops automatically after hands are removed.

Basic use

Dryflow-Slimforce-Hand-Dryer-fig-7

Adjustment

MAINTENANCE

Periodic cleaning of the unit is recommended.
Remove cover and clean dryer dust lint.
Wipe the cover with a damp cloth and mild cleaning solution. Do not soak. Never use abrasives to clean the cover.

DIAGNOSTICS & REMEDIES

WARRANTY

All of our dryers are designed and manufactured to provide years of dependable performance. Component parts are guaranteed to be free of defects in material and workmanship for a period of one (1) year from date of original invoice. This guarantee will be honored provided
that the dryer is installed and maintained in accordance with the instructions. Parts damaged during the installation are the purchaser’s responsibility. The warranty covers defects exclusively, and only liability for the replacement of defective parts will be accepted. This warranty does not cover wear and tear, or misuse and abuse. Defective parts must be returned, accompanied by the serial number, to the point of purchase.
This warranty is granted solely to the original purchaser of the unit and is subject to registration.

Periodic cleaning of the unit is recommended. Remove cover and clean dryer dust lint.

Cleaning stainless steel

Stainless steel is highly resistant to rust, but there are some very strict cleaning and maintenance rules to be followed to prevent damage to its appearance.

General cleaning tips

Apply neutral detergents formulated for these purposes (non-ionic surfactants and citric acid). Apply the detergent with soft cloth. Be careful with abrasive cloths. They may scratch the surface. Rinse with water until all the detergent has gone.
Residue from hygiene products, liquid soap, shampoos, bath gel, etc, can also damage surfaces.
Rinse the surface with plenty of water after use.
Limescale stains can be prevented by drying the surface with a soft cloth after use.

Dryflow-Slimforce-Hand-Dryer-fig-9

Specific cleaning tips

Limescale from mains water: Apply a solution of one part vinegar and three parts water directly to the stains and leave to work for a few minutes. Then rub with a soft cloth or damp sponge. Then give it a final wash with plenty of water and neutral soap to ensure it is thoroughly rinsed.
Unacceptable practices (loss of guarantee)

Do not apply detergents with abrasive products or which contain:
Hydrochloric acid
Sodium hypochlorite (bleach)
Formic acid.
Do not use abrasive utensils like metal sourcing pads or abrasive sponges.
Do not spray the detergent on the surface, because the liquid can get into the openings or cracks in them and cause damage.
Do not use anti-limescale and descaling cleaning products. They are not suitable for cleaning stainless steel.
Do not use silver cleaners, contain chlorides that attack stainless steel.

Warning. Important to avoid (loss of quarantee)

Bleach and descalers are often applied to bathroom equipment and left to work for a time. This leads to the release of gases that contain chloride, which together with the water in the surface cause chlorides to run down the surface of the stainless steel. This rusts both internal and external surfaces.

DIAGRAM BY STANDARD CIRCUIT BOARD

Dryflow-Slimforce-Hand-Dryer-fig-10

Surface-Mounted ADA-Compliant

Dryflow-Slimforce-Hand-Dryer-fig-11

FAQ

Q: Can children use the Slimforce Hand Dryer?

A: Yes, children aged 8 years and above can use the hand dryer under supervision and proper training on safe usage.

Q: What should I do if the power cord is damaged?

A: If the power cord is damaged, it must be repaired by qualified personnel to avoid any risks. Do not attempt to use the dryer with a damaged cord.

Q: How do I clean and maintain the hand dryer?

A: Cleaning and maintenance should be performed by adults and not by children. Ensure the power is switched off before cleaning, and use a soft cloth to wipe down the exterior of the dryer. Do not immerse the unit in water or use harsh chemicals for cleaning.