Dryflow DFADDMo4 AquaDry Tap Dryer Instruction Manual

Dryflow DFADDMo4 AquaDry Tap Dryer

DFADDM04 – Black
DFADDM03 – CMP Chrome plated

• Its plug-in back plate design ensures easy install and maintenance, allowing the control box to be exchanged by a non-electrically qualified person.
• Combines an automatic tap and hand dryer so you can wash and dry your hands at the basin, made from high grade, solid brass.
• 2 sheets of air are used to wipe the water from your hands into the sink. No dripping on the floor. No extra floor space needed for hand drying and washing.
• Eco-efficient high speed hand drying.
• Fitted with a HEPA filter to remove 99.9% of bacteria and viruses from the air.
• Allowing over basin drying helps to minimise washroom clean up, and prevent slips as it eliminates water spillage on floors.
• Great for washroom areas with little wall space.
• A brushless, carbon free motor offers a long service life.
• An intelligent heating system will detect the ambient temperature of your washroom, it automatically adds heat to the airflow if it senses a room temperature drop below 25’C.
• Low noise with smart air outlet design – The airflow direction and speed has been carefully configured to ensure that there is no excess splashing or spray created and therefore works with most sinks.

Pre-installation information

• Warning
  If the unit is not used as directed or safety guidelines are not followed. this could lead to serious injury.

• Do not use in the following environment
  Don’t immerse in water
  High light intensity environments

• Do not allow the motor bucket to get wet
  This will cause electric shock

• Do not modify and disassemble the unit unnecessarily
  This may cause a fire. electric shock. or personal injury
  Use indoors only

• Installation work should be done by a qualified electrician
  Incorrect wiring can cause electric shock and fire

• The installation must provide strong support for the unit, ensuring it is securely affixed to the surface
  If unit is not secure it may cause injury

• Do not attempt to install the unit with the power on
  This may cause electric shock

• Install residual-current circuit breaker
  If not installed there is a risk of electric shock

• If the unit doesn’t work, turn off the power and the ground-fault circuit breaker
  Contact a qualified electrician

• Before you clean the unit, turn off the power switch.

• If the power supply cord is damaged, it must be replaced by a qualified electrician

Sink dimensions

Size of sink minimum: 350mm x 300mm
Internal depth of sink minimum: 100 mm

TECHNICAL SPECIFICATION

Pre-installation information: Space under the sink and electrical supply

Make sure the space is enough to install the unit

Only the following is advised.
The motor bucket cannot be mounted upside down, The motor bucket cannot be installed above the sink, 100mm minimum clearance from bottom of motor bucket to floor /wall.

Please note: Local electrical regulations must be adhered to when installing or repairing the product

Water temperature control
If warm water is needed, please install thermostatic mixer.

Tap mounting
When multiple taps are installed side-by-side, tap centres should be a minimum of 600mm apart.

Tools required

1. Electric drill (drill bit 8mm)
2. Phillips screwdriver-long handle
3. Flat head screw driver 4. Spanner

Spare parts required
1.Water entry hose (not supplied)

Product size

Diagram

Electrical

Tap

Materials and other data

INSTALLATION

Filter replacement
For optimum usage, we advise replacement of the filter every 6 months.

Terms of Guarantee

• The warranty for this unit is 10 years from the time of purchase.

• During its warranty period, a unit can be returned to us and replaced or fixed free of charge, this includes all parts and labour and the cost of returning the unit to you.
  Outside the warranty period, we will cover all labour costs, all you will pay for are the parts and transportation.

• Parts prices are minimal, and certainly much cheaper than a new dryer. We will always let you know the full cost before you purchase, so you are able to make a fully informed decision.

• The hand dryer must be installed by an approved electrician in accordance with the manufacturing guidelines and registered online at www.dryflow.com/register within 28 days of completion of the works, any failure to do this will result in a void of guarantee.

• This warranty is in addition to and supplements your statutory rights and those rights are not affected in any
  way. If you do not register for the extended warranty within 28 days then the standard warranty will apply.

What’s Covered?
Dryflow guarantees that our hand dryers are free from defects at the time of purchase. For this Lifetime Guarantee to apply you must follow the care and use instructions provided with your product.

What’s Not Covered?
This guarantee does not cover damage caused by water damage, accident, misuse, abuse or damage beyond fair wear and tear.

Who’s Covered?
The original purchaser of the product is covered by this guarantee. Cover will cease should the product be sold or otherwise transferred to any other user.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>