IDOLmain UHFX1B, UHFX1R Intelligent Sensing Wireless Microphone System Instruction Manual

IDOLmain UHFX1B, UHFX1R Intelligent Sensing Wireless Microphone System

INSTRUCTION MANUAL

Model: UHFX1B, UHFX1R

Intelligent mute, automatic energy saving, intelligent shutdown

Preface

Wslcome and thank you for purchasing our wireless microphons systsm!

With years experience to producing wireless microphone svstem. our crows arc coofido11t to sav we arc the export of manufacturing wireless microphone systom.

Our products arn suitable for KTV room, karaoke stage and also school, showplace. stadium, and so on. Our products are convenient to operate. a1ld of stably grnat quality. So they are widely favourad by our customers. We promise highly of first class quality, and also first class service.

Our professional technician crew Is always ready to help you with any technical questions !

Procedures for the safe use

1. read the user guide .. read carefulty about safety and manipulation requests.
2. keep the manipulation introductions-pfease keep this manual for further need of safety and manipulation requests.
3. bcware of tho wamings.,plcase notice the warnings for the machine while operating.
4. follow the dcnotomcnts-ptcasc follow the denotcmcnts while operating.
5. accossional devices-only aecessionaJ devices from original produce·rs of tho machino are rcquired.
6. humidity cautions-kee p the mach ine away from humid co1\dictio1\S

7. acration-plcase keep the machine in well ventilated conditions at all time, there should b-0 at least 5cm clearance around the d evice.
8. heat source-please keep the devices ·away from heat sources, including, radiator, heater, .stove, etc
9. power supply-please ut:llil:e the labeled voltage on the device.
10. no exposed fire should be no the device e.g. ftammg candles

11. please do not litter the baneries, dispose them into the appointed pl.ace whan they are fulty used.
12. 110 liquid or weights should be on the device. no water dripping or splashing onto in to the device.

13. the device is also suitable in torvied ione, and variable z.one.

Warning: Beware of electric shock fine; machine must be kept away humid conditions/

NOTE: Only Professional can dissamble and Assemble the system.

Digital pilot Series induction microphone system characteristics

Industry automatic induction hand patent technology, left hand phone still within 3 seconds after automatic mute (any direction, at any Angle Can be), automatic energy saving into standby mode after 5 minutes, 15 minutes after the automatic shutdown and completely cut off the power supply, is a new The concept of intelligent, automated wireless microphone

– new audio circuit structure, the high is exquisite, the low frequency is strong, especially on the details of sound with perfect performance.super Strong dynamic tracing ability makes far/near distance easy pick up charge
– a new concept of digital pilot technology, completely solve KTV rooms each string frequency phenomenon, never string frequency!
– configuration has the noise suppression function circuit, debugging easier
– automatic search no interference channel function, installation more convenient
– free to limit output maximum volume, adapt to the range
– UHF frequency band, phase-locked loop (PLL} frequency synthesis
– 100 * 2 channel, channel spacing 250 KHZ
– superheterodyne secondary frequency conversion design, have extremely high receiving sensitivity

– rf part adopts multilevel high-performance medium filter, good anti- interference ability
– the first intermediate frequency acoustic filters, the second intermediate frequency use level 3 ceramic filter, very good to improve the anti- interference ability
– especially the mute circuit design, completely eliminate the microphone turned on and off the I mpact of the noise
– the microphone use tesco 5 batteries, with up to 6-10 hours
– the microphone adopts unique design of booster battery down does not affect the hand cannot overall performance
– the ideal environment for operating radius of 80 meters, suitable for all kinds of requirements
– the default configuration for LCD backlight blue, mike duct aluminum alloy body
– have adjustable adjustable transmission power and noise threshold, after receiver panel is set external noise control knob, can be in 10 meters
– according to need Flexible setup effective radius of operation between 80 metres
– have ir automatic frequency function, can make the microphone to work fast synchronization and receiver channel
– KTV engineering special models, two microphone, a host.Easily configure more than 100 KTV rooms, the product structure design is unique,Quick and easy maintenance.

Applicable occasions: suitable for high-grade KTV room, small and medium- sized performances, classroom, meeting room, etc., is this year’s key new products, are extremely Customer welcome.Packing type: conventional color box packaging (see sample)

Simulation of pilot Series induction microphone system characteristics

Industry automatic induction hand patent technology, left hand phone static 3 seconds automatically mute (any direction, place both at any Angle), automatic energy saving after 5 minutes, 15 minutes and automatic shutdown completely cut off the power, is a new concept of the intelligent and automatic. The wireless microphone

– new audio circuit structure, the high is exquisite, the low frequency is strong, especially on th details of sound with perfect performance.super

The dynamic tracking ability makes far/near distance easy pick up charge.
– UHF frequency band, phase-locked loop {PLL) frequency synthesis
– 100 * 2 channel, channel spacing 250 KHZ
– superheterodyne secondary frequency conversion design, have extremely high receiving sensitivity
– rf part adopts multilevel high-performance medium filter, good anti- interference ability
– the first intermediate frequency acoustic filters, the second intermediate frequency use level 3 ceramic filter, very good to improve the anti- interference ability

– the first intermediate frequency acoustic filters, the second intermediate frequency use level 3 ceramic filter, very good to improve the anti- interference ability
– especially the mute circuit design, completely eliminate the microphone turned on and off t impact of the noise
– the microphone use tesco 5 batteries, with up to 6-10 hours
– the microphone adopts unique design of booster battery down does not affect the hand cannot overall performance
– the ideal environment for operating radius of 80 meters, suitable for all kinds of requirements
– the default configuration for LCD backlight blue, mike duct aluminum alloy body
– have adjustable adjustable transmission power and noise threshold, after receiver panel is set external noise control knob, can according to need 10 m – 80 m between flexible setup effective radius of operation
– have ir automatic frequency function, can make the microphone to work fast synchronization and receiver channel
– with the function of simulation pilot, can effectively solve the false receiving noise
– KTV engineering special models, two microphone, a host.Easily configure more than 100 KTV rooms, the product structure design is unique, Quick and easy maintenance.

Applicable occasions: suitable for high-grade KTV room, small and medium- sized performances, classroom, meeting room, etc., is this year’s key new products, are extremely Customer welcome.Packing type: conventional color box packaging (see sample)

Intellisense receiver using operation

This series product is composed of handheld mic and receiver, including audio output cables, batteries, frame and auxiliary installation Form a complete set screw, such as product specification attachment.

Intellisense receiver function

(1)Power on key: tap (1) power on LCD light, long press (1) power on key for 3 seconds, LCD off, power off.

(2) “SET” confirmation key; Long press (2) to enter automatic frequency search;

Press (2) “SET” key to select left and right, press (3) ” ” (4) ” ” key to select the current menu To change the status, press (2) “SET” key to SET it to take effect.
(3) ” ” up key, (4) ” ” down key.

(5) Liquid crystal display (LCD): display channel, mute, receive signal level, audio power equality.
(6) Infrared frequency window: with the “SET” key, the channel parameters to the transmitter. ((7) “-” volume reduction key,(8) “+” volume increase key.

Press 1 power button+right” ” button is to switch between high and low power. Press 1 power key+left” ” key+right” ” key is digital pilot switch.

(10) Power outlet: DC 12V500mA power input outlet. The central electrode of the outlet is connected to the positive voltage.
(11) The antenna jack
(12) Audio mixed output: Two signals are mixed together for output.
(13) SQ: Counterclockwise, i.e.,”-” direction, the receiving sensitivity becomes lower and the receiving distance becomes shorter, but the anti- interference capability becomes stronger, and vice versa.
(14) Audio output: suitable for long distance connection effectively reduce noise due to cable.

Receiver LCD Display

1. Level 6 RF level display: display the received RF signal intensity.
2. Level 6 audio level display: display the size or audio signal.
3. Frequency menu display: MHZ displays the current working frequency.
4. Channel menu display :CH displays the current working channel.
5. MUTE display: When MUTE is on, no RF signal is received.
6. Volume display: display the volume.

The use of the Digital pilot series receiver operation

1. automatic sound suppression function

First press the host power button to turn off the host power. and then press the volume”+” button on both sides of the host at the same time to power on the host. (After shulling down the host, press the volume on both sides of the host and hold the button, and then press the power button to power on the host, you need to press three buttons al the same time.) The host displays “O”. The Factory default is 0. The adjustanent range is 0-5. O indicates that automatic howling suppression is disabled. The highest level is 5. You are advised to use the default setting or adjust the setting based on site requirements. Adjustment method:
Click the volume up and down button on the right, and press the SET button on the right to save the adjustment. Note: this function only works iF both hands are used at the same lime.

2. dynamic search idle channel function

In a complex environment, it takes a lot or lime to manually select the channel without interrerence. The new system is configured with the function of automatically searching the channel without interference. The operation mode is as follows:

Long press “SET” key for more than 2 seconds to loosen. the host into the automatic search no interrerence channel Function, when the host search to no interference channel, flashing display the current search to no interference channel, the open hand, handle the mi screen location on the host “IR” launch window, press the “SET” key once again and infrared frequency of operation.

3. host lock and unlock

Press the power button to shut down the host, hold down the left ” ” button (frequency reduction button), and press the power button to start the machine at the same time, to realize· unlock, enter the unlock menu in the same way each time, the lock button state will be reversed once. So if it was locked before, it’s unlocked, if it was unlocked before, it’s locked. The “key” symbol on the host is displayed if the host is locked, but is not displayed if the host is unlocked .

4. internal hidden debugging mode

Press the power button to shut down the host, while holding down the”•” button (frequency plus button) on both sides, while pressing the power button to power on, enter the 1 D encryption menu settings. “ID SET” is displayed on the left screen and “ID ON” is displayed on the right screen. Press the frequency addition and subtraction button on the right to switch the ID ON switch state. After adjustment, press the confirm button on the right
to save. ID ON” is set in normal mode, in which the host is used only with the last successful set of the microphone. ID OFF” is the test mode. Under this mode, the host can be paired with any hand microphone with the same frequency point. At the same time, the host is easy to be crossed-frequency, so it is only used temporarily. The default “ID ON” prevents crosstalk.

5. Switching between high and low power

In order to adapt to different use occasions, the wireless system is designed with high and low power switch. In high power state, the use distance is the longest (effective use distance is about 100 meters in open space), and the power consumption of the microphone is large. In the low-power position, the transmitting power of the microphone is low, the operating distance is short (the effective operating distance is about 50 meters in open space), and the power consumption is small. You can set the parameters as required.

1. In shutdown state, press the power key” “+ the lower right key” ” to appear the above interface, at this time can switch the power state;
2. Press” ” and” ” to switch the state, and press “ SET ” to confirm
3. After switching the power each time, the microphone must reset the frequency before it can be used.

Note: In the ID ON state, the host can display the battery power of the hand phone in real time. In the ID OFF state, the host will not display the battery power of the hand phone. After setting the ID function, press the SET key on the right to enter the MENU for setting the ID encryption algorithm. This function is not generally used. When more than 200 microphones are used in a unified place at the same time, you need to change the encryption algorithm. The default setting is “I D-1 “. When more than 200 microphones are used, you need to set this parameter to “ID-2”. Press SET to save and exit

Note: Since each frequency point of the machine adopts an independent encryption algorithm, the host can only be used with the last paired hand microphone. If the frequency point of the hand microphone is the same as that of the host, but there is no voice output. Re-operate the infrared frequency can be.

Description of the appearance and structure of the microphone

1. Liquid crystal display
2. Infrared receiving window
3. Power switch
4. The tail cone
5. Battery compartments

Intelligent induction series of the operation and use of microphones

1. THE INDUCTION FUNCTION ON AND OFF.

Open hand, after the backlight goes out, hold down the power button not holding (note: don’t let go, 2 seconds, will cause the mi normal shutdown (electricity at this time Source buttons or not), after waiting for ten seconds hand microphones will be automatically switched on, and show the sen on (induction function open) or sen off (table Induction function in closed), then the power release button, hand microphones into normal work mode. Open and close the induction function is the same operation, simply Repeat operation. Note that the hand microphones in the process of the whole power button is not according to loosen

2. INFRARED FREQUENCY:

Press the set key of the host to enter the infrared frequency matching mode. The specific operation mode is to open the hand microphone, align the display screen of the hand microphone with the IR transmission window of the host, press the set key of the host, and the hand microphone will automatically synchronize to the frequency point set by the host.

3. START-UP AND SHUTDOWN OPERATION

Light about 2 seconds, the power button down microphone display will light up and the LCD screen will display information related work, including working frequency (channel), battery and other information. Every time must pay attention to check the battery when the phone is switched on display status, according to the practical to use the length of time to choose whether to replace the battery. In general, a pair of ordinary 5 8 hours the battery can be normal use. When the battery is 1 case, screen flashing shows LOW voltage will prompt “LOW BAT”, shows that the battery is about to run out of, please replace the battery. In addition, the display backlight will automatically put out a few seconds after switch on the microphone into energy saving mode, if you need to look at the screen when using the information, press the power switch can light. Press the power switch not to put about 3 seconds, the display shows “OFF”, after the microphone will be turned OFF. When the microphone when not in use for a long time, please take out the battery, circuit board to avoid battery leakage corrosion and damage the microphone.

4. INSTALLATION, THE MICROPHONE BATTERIES

Hand held microphones from the packaging, unscrew the tail cone, according to the polarity of labeled into 2 section 5, battery, and then turning the tail cone.

Note: The microphone may be damaged if the battery is mounted in reverse direction.

Digital pilot series of main technical parameters

Frequency range ………………………….. 530-58OM HZ
Tunable channel number ……………… 100 x 2
Oscillation mode ………………………….. Phase-locked loop (PLL) frequency synthesis
Frequency stability. ………………………. Plus or minus 10 PPM
Reception mode ………………………….. Secondary superheterodyne frequency conversion
Pilot way ……………………………………… Digital pilot
Receiving sensitivity. ……………………. – 95 – -67 DBM
Frequently ring tone …………………….. 40-18000 hz
Harmonic distortion ……………………… 0.5% or less
Signal to noise ratio …………………….. 110 db or higher
Audio output ……………………………….. Equilibrium output and mixed output
Transmission power …………………….. 3-30 mw
Modulation mode ………………………… Frequency modulation (FM)
The battery specification ……………….2 no.5 batteries
Power supply specifications …………. 10 0 -240 – v 50-60 hz 12 voe power adapter (switch)
12 voe or 220 vac / 50-60 hz (linear power supply)
The power consumption ……………… 10 w or less

Simulation of pilot series of main technical parameters

Frequency range ………………………….. 530-580M HZ
Tunable channel number. ……………..1 00 x 2
Oscillation mode ………………………….. Phase-locked loop (PLL) frequency synthesis
Frequency stability. ………………………. Plus or minus 10 PPM
Reception mode …………………………..S econdary superheterodyne frequency conversion
Pilot way. ……………………………………..S imulation of pilot
Receiving sensitivity. …………………….- 95 –67 DBM
Frequently ring tone …………………….. 40-18000 hz
Harmonic distortion …………………….. ?0. 5% or less
Signal to noise ratio ……………………… 11 Odb or higher
Audio output ……………………………….. Equilibrium output and mixed output
Transmission power. …………………….3 -30 mw
Modulation mode ………………………… Frequency modulation {FM)
The battery specification ………………. 2 no.5 batteries
Power supply specitications …………. 100-240 – v 50-60 hz 12 VDC power adapter (switch)
12 VDC or 220 vac / 50-60 hz {linear power supply)
The power consumption ……………… 10 w or less

Operation method and attentions

Operation method:

1. Connect the audio system well;
2. Set the volume of the receiving machine and the loudspeaker to mix;
3. Turn on the power of the audio system from backing stage to backward stage;
4. Trun on the power of the transmitter;
5. Adjust the audio effect of the audio system: firstly, adjust the volume of the receiving machine to the middle point, turn on the microphone, talk directly forward the microphone, fit the volume secondly, adjust the tone, volume controller carefully and make the voice clear, the volume suitable. Add the phone and hare the “on show” proless;

6. If the wireless receiving machine system has some problems. Please reference this funcation hare troubleshooting and solve the problem. If the problem is not in the troubleshooting. Please onse the professional to sowe it or hegotiate with the franchiser;
7. After using, please turn off the power of the transmitter, than turn off the power of all the owdio system from backing stage word backword stage.

Attentions

1. The erect location of the antenna effect the leleption effect of the leceiving machine directly, so take attention to the installation method. If is the most important principle that keep the distance between the microphone and the leceiving machine shortest.
2. Avoid putting the receiving machine hear the computer or other equipment which can produce RF signal.
3. Avoid putting the receiving machine in the orlop of the DB, exclude the installation antenna from distance.
4. This receiving machine system can fill 200 microphone at the same time, and it could not disturb each other. If need to be adjusted different channels by professional.

5. When some wireless systems are used at the same time, pleas take attention to the setting of “SQ” of the receiving machine. The lower the sensitive is the shorter the capacity of disturbance could be!
It is better that the transmit phone is short. It can save the electronic and decrease the jamming at the same time.

PROBLEM & SOLUTION

Troubleshooting

Some common problems and their solutions are identified in the table below. If you are unable to solve a problem, Please contact your dealer for solutions.

the transmitter and the receiving machine. see whether it is on the play of “NO”
• Check whether the “negativre” and the “pos tive” pole of the battery is confusing
• Check the connecting solution of the receiving machine and the aerial.
• Make sure that there is no block between the aerial and the transmitter.
No voice(situation:RF display is nomal; AF display is nomal)| • Check whether the voice re knob of the receiving machine is on the lowest place.
Check whether the connecting between the
• loudspeakers of the receiving machine are nomal.
No voice(situation: RF display is nomal; AF display is un-nomal)| • Check whether the power of the transmitter is open Exchange the mike of the transmitter when it is necessary
Put through the transmitter, there is some noise or some interruption noise in the receiving signal| •  Check whether the battery is tight enough.
•  Eliminate the RF source of the disturbance rearby.
•  Check the connecting situation, if using githar or other mascial instrument.
•  If both of the transmitters are using the same frequency, check it and close one of them.
•  maybe thesignal is too infirmness, adjust the place of the antenna more it as near the transmitter
as possible.
•  Replace other channel.
---|---
There is some noise, after closing the transmitter.| •  Adjust the sensitivity button of the transmitter, the “SQ” button.
•  Eliminate source of noise of RF.
•  Adjust the place of the receiving machine or the place Of the antenna over again.
While the showplace is moving, the voice from the transmitter may get lost sometimes.| •  Adjust the sensitivity button of the transmitter; the”SQ” button.
•  Locate the receiving machine over again and hare the “on-show” experiment. Obserre the RF display.
•  If youfind some voice lost, tag the point and avoid this point when performing.
Can not open the transmitter.| •  Change the battery of the transmitter..

Specifications:

• Compliance: Part 15 of FCC Rules
• Radiation Exposure Limits: FCC approved
• Minimum Distance: 0cm between radiator and body

FCC Warnning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications.

However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

FAQ

Q: Can I modify the device?

A: Any changes or modifications not approved by the manufacturer may void your warranty and authority to operate the equipment.

Q: What are the FCC compliance conditions?

A: The device must not cause harmful interference and must accept any interference received.

Q: How far should the device be from my body during operation?

A: The device should be operated with a minimum distance of 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>