Dryflow JJ01 Jet Force Junior Hand Dryer User Manual
- June 5, 2024
- Dryflow
Table of Contents
Dryflow DFLIF02 Slimforce Hand Dryer
SAFETY WARNINGS
- Before installing, be sure to read this installation manual and retain for future reference.
- This product must be installed by qualified personnel in accordance with the instructions given in this manual and installation must comply with all applicable regulations, national security standards and laws in force in the country where the product is installed.
- Turn off the power at the main switch before installing or servicing the dryer unit.
- The dryer must not be installed on a flammable surface. Do not damage any parts of the electrical connections.
- Pre-arrange an appropriate power outlet and a system of disconnection in accordance with current local regulations. Make sure the product is properly connected to ground. If there is no ground connection, there is a risk of an electrical shock.
- Do not install the dryer over a washbasin. If the power cord is damaged, it must be repaired by qualified personnel to avoid any type of risk.
- This dryer can be used by children aged 8 years and above. People with reduced physical, sensory or mental abilities or lack of experience and knowledge, if they have been given supervision and appropriate training regarding the use of the dryer in a safe manner, can use it with no restriction. Children should not play with the apparatus. Cleaning and maintenance performed by the owner should not be done without children having supervision.
- During use, temperatures above 158℉ [70℃] may develop in the parts near the hot air nozzle. Do not touch or cover the dryer during use or when finished using it.
WARNING
This product is intended for installation by a qualified service person.
Use AWG NO.12 solid conductor for wiring
NOTE: Do not install dryer over washbasin
PACKING LIST
| ITEM KEY | ITEM DESCRIPTION | ITEM QTY | NOTES |
|---|---|---|---|
| A | Hand Dryer Unit Complete | 1 | Stainless Steel 304 Cover & Cabinet |
| B | Owner Manual (OM – this booklet) | 1 | |
| C | Mounting Template (MT) | 1 | |
| D | Wall Anchors, Expansion | 4 | Φ8x38MM [ 5/16″ Dia.x 1-1/2″], for#10 |
| E | Self-threading Phillips PH Screws | 4 | M5x36MM [ No.10 AB x 1-3/16″] |
| F | Flat Washer | 4 | F1 For M5[No.10 AB]Phillips PH Screws |
| G | Hex Key (for cover screws) | 1 | For 4MM[ 5/32″] hex socket FH Screws |
SPECIFICATION
- Voltage: 220V-240V 50/60Hz,4A/1000W
- Stand-by Power: L e ss than 2.0W
- Air Temperature: 4 0 ℃[104°F](Distance from nozzle=100MM[4″],Room Temp.=25℃[77°F])
- Air Velocity: 1 0 0M/S[328 FT/S] / 360KM/H[224MPH]
- Air Flow: 1 3 0M3/H[76.5CFM]
- Drying Time: 1 0 -12 Seconds
- Timing Protection: Forced Hold-On 60 Seconds auto shut-off
- Timing Duration:
- Auto Shut-Off ≤3 Seconds after last sensor read
- Sensor Range: 5-15CM[2″~ 5-7/8″], Owner Adjustable
- Fuse Protection: 1kW,Main PCB, Φ5×20, 250V, 6A[230V]
- Protection Level: IP23
- Electric Isolation: CLASS ǀ (Metal cover)
- Brush Motor: 30000RPM, 600W[0.8HP]
- Noise [at 1M]: 74dB
- Weight : 2.5KG[5.5lb]/Net Weight / 3.0KG[6.6lb]/Shipping Weight
BEFORE INSTALLATION
Installation must be carried out in accordance with the current edition of the local wiring regulations code having jurisdiction. Installation should be performed only by a qualified electrician Hand dryer is to be installed with hardwired stub provided in advance of install by others. See MT for complete reference to mounting heights and power KO locations
L Min.= 300MM[11-13/16″]
It is recommended to avoid installation of dryer near high reflective objects (mirror, stainless steel washbasins, etc.) in order to avoid faulty function of the presence sensor.
INSTALLATION
- Be sure to turn off the electric supply before any operation.
- Place template against wall at desired height (see mounting height recommendations) and mark locations of 4 mounting holes Dia. 8mm(5/16″).
- Remove hand dryer back transportation only purpose screw.
- Remove and retain 2 side security hex cover screws and cover.
- Mount the hand dryer base on the wall.
- If the hand dryer is supplied in hardwired:
- Connect the live wire(Coloured Brown, Red, or Black) to the terminal block marked “L”.
- Connect the neutral wire(Coloured Black, Blue) to the terminal block marked “N”.
- Connect the ground wire(Coloured Green or Yellow) to the terminal block marked “E”.
- Before replacing cover, there is a customized option to run the dryer heater on (1000W) or heater off(600W).The switch is clearly marked.
- Default setting is 12-15CM from nozzle. If it needs and please adjust its range.
- Replace cover. Do not over-tighten screws.
OPERATION
No-touch operation. There is a blue LED light to guide user to the air flow. Shake excess water from hands. Place hands under the outlet to start operation. Rub hands lightly and rapidly. Stops automatically after hands are removed.
Basic use
- Operation without touching, place your hands under the exit to activate the device.
- There is a blue LED light to guide the user towards the air flow.
- After several seconds without detecting hands, the equip- ment stops automatically.
ADJUSTMENTS
- It is possible to turn on/off hot air with a switch located inside the unit (see section 7 in “Insta- Ilatian”
- It is possible to adjust the detection distance by means of the potentiometer located inside the unit see section 8 in “Installation”).
MAINTENANCE
- Periodic cleaning of the unit is recommended.
- Remove cover and clean dryer dust lint.
- Wipe the cover with a damp cloth and mild cleaning solution.
- Do not soak. Never use abrasives to clean the cover.
DIAGNOSTICS & REMEDIES
|
---|---
Hand dryer fails to start| Ensure the breaker supplying the dryer is
operational. If it is, disconnect the power and remove the hand dryer cover.
| Check all the wire connections to make sure they are well fixed.
| Turn on power and if it does not work then replace circuit board.
| Turn motor blower several times by hand to see if it is blocked.
Hand dryer turns| Ensure that there is no obstruction on or in front of the
infrared
on/off erratically or not sensitive enough| sensor zone. Clean any dirt off
the sensor lens.
Try adjusting the sensitivity potentiometer on program board. If still not working, replace circuit board and sensor board.
Not hot air
|
Check if the heat element switch is power on.
Check if the heat element was broken. If yes, replace a new one.
Hand dryer makes ticking noise| Check the motor brush worn condition. Replace them or a new motor.
WARRANTY
All of our dryers are designed and manufactured to provide years of dependable
performance. Component parts are guaranteed to be free of defects in material
and workmanship for a period of one (1) year from date of original invoice.
This guarantee will be honored provided that the dryer is installed and
maintained in accordance with the instructions. Parts damaged during the
installation are the purchaser’s responsibility. The warranty covers defects
exclusively, and only liability for the replacement of defective parts will be
accepted. This warranty does not cover wear and tear, or misuse and abuse.
Defective parts must be returned, accompanied by the serial number, to the
point of purchase.
This warranty is granted solely to the original purchaser of the unit and is
subject to registration.
MAINTENANCE
Periodic cleaning of the unit is recommended. Remove cover and clean dryer dust lint. Stainless steel is highly resistant to rust, but there are some very strict cleaning and maintenance rules to be followed to prevent damage to its appearance. Apply neutral detergents formulated for these purposes (non- ionic surfactants and citric acid). Apply the detergent with soft cloth. Be careful with abrasive cloths. They may scratch the surface. Rinse with water until all the detergent has gone Residue from hygiene products, liquid soap, shampoos, bath gel, etc, can also damage surfaces. Rinse the surface with plenty of water after use. Limescale stains can be prevented by drying the surface with a soft cloth after use.
Limescale from mains water: Apply a solution of one part vinegar and three parts water directly to the stains and leave to work for a few minutes. Then rub with a soft cloth or damp sponge. Then give it a final wash with plenty of water and neutral soap to ensure it is thoroughly rinsed. Unacceptable practices (loss of guarantee)
- Do not apply detergents with abrasive products or which contain: Hydrochloric acid Sodium hypochlorite (bleach) Formic acid.
- Do not use abrasive utensils like metal sourcing pads or abrasive sponges.
- Do not spray the detergent on the surface, because the liquid can get into the openings or cracks in them and cause damage.
- Do not use anti-limescale and descaling cleaning products. They are not suitable for cleaning stainless s teel.
- Do not use silver cleaners, contain chlorides that attack stainless steel.
Warning. Important to avoid (loss of guarantee)
Bleach and descalers are often applied to bathroom equipment and left to work
for a time. This leads to the release of gases that contain chloride, which
together with the water in the surface cause chlorides to run down the surface
of the stainless steel. This rusts both internal and external surfaces.