LEAB 1051009024 CAN-LIN Gateway User Guide
- May 15, 2024
- LEAB
Table of Contents
LEAB 1051009024 CAN-LIN Gateway
Safety
This Quick Start Guide is intended to support safe handling of the CAN-LIN Gateway. Observe the safety instructions:
WARNING! Risk of injury from electric shock. Disconnect the vehicle
negative cable prior to Installation.
WARNING! Fire hazard due to short circuit: Secure your vehicle with an
additional fuse installed near the unit.
NOTE! Penetrating water can damage the unit: Prevent water from entering
the housing during cleaning.
NOTE! The unit is designed for interior use only. Do not mount the unit
outside the vehicle.
NOTE! Installation must only be carried out by qualified electricians.
About this product
The CAN-LIN Gateway provides the most important data of the LPS II on the CI
bus and therefore allows the LPS II to be integrated into a CI bus on-board
management system.
In addition to information on current, voltage and power for solar, vehicle
power circuit and external feed, the charging status of the LPS II is provided
on the CI bus. In the same way, the 230 V/12 V output as well as the jump-
start function of the LPS II can be switched on and off.
Package content
No. | Name |
---|---|
1x | CAN-LIN Gateway |
1x | Quick start guide |
Accessories (optional)
CAN-LIN Gateway connection cable to LPS II
Part number| 1601001136
Cable length:| 5 m
Connections:| open cable end on M12 connector
Technical specifications
| CAN-LIN Gateway
---|---
Part number| 1051009024
Power consumption| 18 mA
Voltage range| 9.8 V….. 14.6 V DC:
Temperature range| -20 °C … +75 °C
Protection class| III
Housing| 7-pin relay socket housing
BUS system connections| CAN bus/LIN bus
Dimensions (L x W x H)| 60 mm x 30 mm x 30 mm
Weight| 30 g
LIN bus parameters
The following commands and information can be transmitted or controlled via the LIN bus system:
Information | Command |
---|---|
12 V/230 V input current | Capacity:12 V/230 V/solar |
on/ off
12 V/230 V output current| Operating status| Switch emergency start func- tion
on/off
12 V/230 V input voltage| Error levels|
12 V/230 V output voltage| Error codes|
Solar power| Firmware version|
Solar voltage| Hardware version|
Battery temperature| Serial number|
Battery current| Residual time|
IO signals| Residual capacity|
SoC (State of Charge)| |
PIN assignment
CAN-LIN Gateway
Pin | Assignment | Description |
---|---|---|
1 | Terminal 31 | Ground (earth) |
2 | CAN (High) | CAN-Bus High |
3 | LIN | LIN bus |
4 | Terminal 31 | Ground |
5 | CAN (Low) | CAN-Bus Low |
6 | n. a. | Not assigned |
8 | Terminal 30 | 12 V DC: |
M12 connector of the connection cable (accessories)
PIN | Assignment | Description | Core colour |
---|---|---|---|
1 | Not assigned | ||
2 | Battery positive | 12 V DC: | Black |
3 | GND | Ground | Brown |
4 | CAN (High) | CAN-Bus High | Blue |
5 | CAN (Low) | CAN-Bus Low | Grey |
Installation
To install the unit, proceed as follows:
NOTE! To ensure the smooth operation of the CAN-LIN Gateway, make sure that the Gateway and the LPS II are at the same ground potential (GND).
✓ A 5-pin M12 connector is available
- Connect pin 3 (LIN) of the gateway to the LIN connection point of the CI bus.
- Connect pin 2 (CAN (High)) of the gateway to pin 4 of the M12 connector.
- Connect pin 5 (CAN (Low)) of the gateway to pin 5 of the M12 connector.
- Connect pin 8 (12 V DC) of the gateway to pin 2 of the M12 connector or the 12 V connection point of your vehicle.
- Connect pin 1 or pin 4 (GND) of the gateway to pin 3 of the M12 connector or the ground of your vehicle.
- Connect the M12 plug to the remote connector of the LPS II.
⇨ The unit is installed.
Disposal
Dispose of the device in accordance with the Waste Electrical and Electronic
Equipment Regulations (WEEE).
The system must not be disposed of with household waste. Take it to a
recycling point or return it to your point of sale.
Customer Support
LEAB Automotive GmbH
Thorns hammer 6
24866 Bedsore
info@leab.eu
+49 (0) 4621 – 97860-0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>