SONY SA-SW3 6.3 Inch 200W Wireless Subwoofer Instruction Manual
- June 4, 2024
- Sony
Table of Contents
SONY SA-SW3 6.3 Inch 200W Wireless Subwoofer Instruction Manual
About compatible models for the subwoofer
The SA-SW3 subwoofer works only with the specified model. For information
about compatible models, visit Sony’s website.
In these Operating Instructions, the operations are described for the
subwoofer used with the compatible model HT-A7000 or HT-A9
Parts and Controls
Front
- Power indicator
- Flashes slowly (green): The subwoofer is not connected to a compatible model.
- Lights up (green): The subwoofer is connected to a compatible model.
- Flashes twice repeatedly (green): The subwoofer is attempting to connect to a compatible model.
- Flashes/lights up (amber): The software is updating.
- Lights up (red): The subwoofer is in standby mode.
- Turns off: The subwoofer is turned off.
Note
The brightness of the power indicator syncs with the DIMMER settings of a
compatible model.
Rear
- 2) (power) button
- 3) LINK button
- 4) AC inlet
Installation
The following illustration is the installation example to use the subwoofer
with the compatible model HT-A7000 and optional rear speakers.
Install the subwoofer in the place that you want.
You can install the subwoofer in the place that you want because the output
sound from it has no directivity.
The above illustration is the example for installation of the subwoofer.
Tip
To obtain a good surround sound, set the subwoofer distance from your
listening position by using the setup menu of a compatible model.
For details, refer to the Operating Instructions supplied with a compatible
model.
Connection
Tip
You can connect the optional rear speaker with a compatible model in the
following way when installing it too.
-
Turn on a compatible model
-
Connect the AC power cord (mains lead) (supplied) to the subwoofer, and then connect the cord to the AC outlets (mains).
-
Make sure that the power indicator on the subwoofer lights in green.
When the power indicator lights in green, the connection between the subwoofer and a compatible model is established.
If the connection is not established, connect the subwoofer to a compatible model manually. For details, see “If the Connection is not Established Automatically”.
If the Connection is not Established Automatically
If you cannot connect the subwoofer to a compatible model automatically or you use multiple compatible models and want to specify the compatible model for connecting the subwoofer, perform the manual connection.
The following operation is described for the subwoofer used with the
compatible model HT-A7000 or HT-A9. Use the remote control supplied with the
compatible model HT-A7000 or HT-A9 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
-
Press HOME.
The home menu appears on the TV screen. -
Select [Setup] – [Advanced Settings] on the home menu.
-
Select [Speaker Settings] – [Wireless Speaker Settings] – [Start manual linking].
The [Start manual linking] screen appears on the
TV screen. -
Press LINK on the subwoofer.
The power indicator of the subwoofer that had
LINK pressed flashes twice repeatedly in green. -
Select [Start].
The manual link starts.
The connecting process appears on the TV screen.
To cancel the manual link, select [Cancel]. -
When [Subwoofer] display [Connected], select [Finish].
-
Press .
The link is established and the power indicator of the subwoofer lights in green.
Note
- If you perform [Start manual linking], [Link mode] of [Wireless Speaker Settings] is set to [Manual] automatically.
- Only the speakers for which [Connected] has been displayed in Step 6 connect to a compatible model.
If the connection of the subwoofer cannot be established, perform the manual connection again.
If Wireless Transmission is Unstable
If you use multiple wireless systems, such as a wireless LAN, the wireless
signals may become unstable. In this case, the transmission may be improved by
changing the following setting.
The following operation is described for the subwoofer used with the
compatible model HT-A7000 or HT-A9. Use the remote control supplied with the
compatible model HT-A7000 or HT-A9 when performing this operation.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
-
Press HOME.
The home menu appears on the TV screen. -
Select [Setup] – [Advanced Settings] on the home menu.
-
Select [Speaker Settings] – [Wireless Speaker Settings] – [RF Channel].
-
Select the setting you want.
- [On] (default setting): Normally select this. The system automatically selects the better channel for transmission. Stronger mode for wireless interference.
- [Off]: The system selects a channel from the limited frequency band to prevent external wireless interference. If sound dropping occurs while [On] is selected, it may be improved by selecting [Off].
Note
- If you change the [RF Channel] setting from [Off] to [On], it may take 1 minute to reconnect.
- A compatible model may not meet this setting depending on countries/regions where you purchase it.
Troubleshooting
If you experience any of the following difficulties while using the subwoofer,
use this troubleshooting guide to help remedy the problem before requesting
repairs. Should any problem persist, consult your nearest Sony dealer.
Be sure to bring all of your subwoofer, a compatible model and optional rear
speakers (not supplied) even if it seems as though only one has a problem,
when you request to repair.
The following solutions are described for the subwoofer used with the
compatible model HT-A7000 or HT-A9.
If you use other compatible models, refer to the
Operating Instructions supplied with them.
No sound or only a very low-level sound is heard from the subwoofer.
-
Press SW + or BASS + on the remote control of a compatible model to increase the subwoofer volume.
-
Make sure that the power indicator on the subwoofer is lit in green.
-
If the power indicator on the subwoofer does not light, try the following.
- Make sure the AC power cord (mains lead) of the subwoofer is connected properly.
- Press (power) of the subwoofer to turn on the power.
-
If the power indicator on the subwoofer flashes slowly in green or lights in red, try the following.
- Move the subwoofer to a location near a compatible model so that the power indicator on the subwoofer lights in green.
- Follow the steps in “If the Connection is not Established Automatically.”
- Check the wireless connection status. For details, refer to the Operating Instructions supplied with a compatible model.
-
If the power indicator on the subwoofer flashes in red, press Æ (power) of the subwoofer to turn off the power and check whether the ventilation holes of the subwoofer is blocked or not.
-
If the input sources contain very little bass sound components (i.e., a TV broadcast), the sound from the subwoofer may be difficult to hear. You can check the subwoofer sound by emitting the test tone.
-
Set the night mode to off. For details, refer to the
Operating Instructions supplied with a compatible model. -
If you change the [RF Channel] setting from [Off] to [On], it may take 1 minute for the sound to be output.
Sound skips or has noise. -
If there is a device nearby that generates electromagnetic waves, such as a wireless LAN or a microwave oven in use, locate the subwoofer and a compatible model apart from it.
-
If there is an obstacle between the subwoofer and a compatible model, move or remove it.
-
Locate the subwoofer and a compatible model as close as possible.
-
Change the [RF Channel] setting.
-
Switch the network connection of the TV or Blu-ray Disc player from wireless to wired.
Specifications
Amplifier section
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC)
With 2 ohms loads, from 28 – 200 Hz; rated 130 W, minimum RMS power, with no
more than 1% total harmonic distortion from 250 mW to rated output.
POWER OUTPUT (reference)
200 W (at 2 ohms, 100 Hz)
Canadian models:
POWER OUTPUT (reference)
200 W (at 2 ohms, 100 Hz)
Speaker system
Subwoofer speaker system, Bass reflex
Speaker
160 mm (6 3/8 in) cone type
Power requirements
120 V AC, 60 Hz
Power consumption
On: 40 W
Standby mode: 1 W or less
Turned off: 0.5 W or less
Dimensions (approx.) (w/h/d)
201 mm × 382.5 mm × 402 mm (8 in × 15 1/8 in × 15 7/8 in) (not including
projection portion)
Mass (approx.)
9.0 kg (19 lb 14 oz)
Wireless transmitter/receiver section
Communication system
Wireless Sound Specification Version 4.0
Frequency band
5 GHz
Modulation method
OFDM
Included items
- Subwoofer (1)
- AC power cord (mains lead) (1)
- Operating Instructions (1)
Important information on software
This product contains software that is subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). These establish that customers have the right to acquire, modify, and redistribute the source code of said software in accordance with the terms of the GPL or the LGPL.
For the method to confirm the GPL, LGPL and other software licenses contained in the subwoofer, please refer to the Operating Instructions of a compatible model.
When you use the compatible model HT-A7000 or HT-A9, please refer to [Software License Information] under [Setup] – [Advanced Settings] – [System Settings] on the home menu.
You may find a copy of the relevant source code as required under the GPLv2 (and other licenses) at https://oss.sony.net/Products/Linux
You may obtain the source code as required by the GPLv2 on a physical medium
from us for a period of three years after our last shipment of this product by
applying through the form at https://oss.sony.net/Products/Linux
This offer is valid to anyone in receipt of this information.
Please note that Sony cannot answer or respond to any inquiries regarding the content of this source code.
All other trademarks are trademarks of their respective owners.
WARNING
To reduce the risk of fire or electric shock, do not expose this subwoofer to rain or moisture.
The subwoofer is not disconnected from the mains as long as it is connected to the AC outlet, even if the subwoofer itself has been turned off.
To reduce the risk of fire, do not cover the ventilation opening of the
subwoofer with newspapers, tablecloths, curtains, etc.
Do not expose the subwoofer to naked flame sources (for example, lighted
candles).
To reduce the risk of fire or electric shock, do not expose this subwoofer to dripping or splashing, and do not place objects filled with liquids, such as vases, on the subwoofer.
As the main plug is used to disconnect the subwoofer from the mains, connect the subwoofer to an easily accessible AC outlet. Should you notice an abnormality in the subwoofer, disconnect the main plug from the AC outlet immediately.
Do not install the subwoofer in a confined space, such as a bookcase or built- in cabinet.
Do not place this product close to medical devices.
This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.
Indoor use only.
For the customers in the U.S.A.
NOTE:
This subwoofer has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This subwoofer generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this subwoofer does cause harmful interference to
radio or television reception, which can be determined by turning the
subwoofer off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the subwoofer and receiver.
- Connect the subwoofer into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
If you have any questions about this subwoofer:
Visit:
www.sony.com/electronics/support
Contact: Sony Customer Information Service Center at 1-800-222-Sony(7669)
Write: Sony Customer Information Service Center
12451 Gateway Blvd., Fort Myers, FL 33913
Supplier’s Declaration of Conformity
Trade Name: SONY
Model: SA-SW3
Responsible Party: Sony Electronics Inc.
Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-2230
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this subwoofer.
This subwoofer must not be co-located or operated in conjunction with any other antenna or transmitter.
This subwoofer complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This subwoofer should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other
words, this device automatically discontinue transmission in case of either
absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm or less
For the customers in Canada
This subwoofer contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development
Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This subwoofer may not cause interference; and
- This subwoofer must accept any interference, including interference that may cause undesired operation of the subwoofer.
This subwoofer complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This subwoofer should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
5.15 – 5.35 GHz band is restricted to indoor operations only.
Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
Precautions
On safety
- Should any solid object or liquid fall into the subwoofer, unplug the system and have it checked by qualified personnel before operating it any further.
- Do not climb on the subwoofer, as you may fall down and injure yourself, or the subwoofer damage may result.
On power sources
- Before operating the subwoofer, check that the operating voltage is identical to your local power supply. The operating voltage is indicated on the nameplate at the rear of the subwoofer.
- If you are not going to use the subwoofer for a long time, be sure to disconnect the subwoofer from the wall outlet (mains). To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.
- One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet (mains) only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
- AC power cord (mains lead) must be changed only at a qualified service shop.
On heat buildup
- Although the subwoofer heats up during operation, this is not a malfunction. If you continuously use this subwoofer at high volume, the subwoofer temperature at the rear and bottom rises considerably. To avoid burning yourself, do not touch the subwoofer.
On placement
- Do not place the subwoofer near heat sources or in a place subject to direct sunlight, excessive dust, or mechanical shock.
- Do not place metal objects other than a TV around the subwoofer. Wireless functions may be unstable.
- If the subwoofer is being used in combination with a TV, VCR, or tape deck, noise may result and picture quality may suffer. In such a case, place the subwoofer away from the TV, VCR, or tape deck.
- Use caution when placing the subwoofer on a surface that has been specially treated (with wax, oil, polish, etc.), as staining or discoloration of the surface may result.
- The speakers of this subwoofer are not of magnetically shielded type. Do not place magnetic cards on the subwoofer or near it.
If you encounter color irregularity on a nearby TV screen
Color irregularities may be observed on certain types of TV sets.
On cleaning
Clean the subwoofer with a soft, dry cloth. Do not use any type of abrasive
pad, scouring powder, or solvent such as alcohol or benzine.
If you have any question or problem concerning your system, please consult your nearest Sony dealer.
LIMITED WARRANTY
U.S. and Canada only -1 year
Sony Electronics Inc. solely for purchases made in the United States and Sony of Canada Ltd. solely for purchases made in Canada (collectively “Sony”) warrants this product against defects in material or workmanship for the original owner and any subsequent end user owner(s) (“You” or “Your) for the time period set forth above as set forth herein. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or recertified/refurbished product of the same (or similar) model. For purposes of this Limited Warranty, “recertified” or “refurbished” means a product or part that has been returned to its original specifications. In the event of a defect, these are Your exclusive remedies. Sony does not warrant that the operation of the product will be uninterrupted or error-free.
Term: For the time period set forth above from the original date of purchase of the product when purchased directly from Sony or Sony authorized dealer (To determine if a dealer is in the Sony authorized dealer network, please visit US: www.sony.com/retailers; Canada: https://dealerlocatorsony.ca/locator; or contact Sony directly), Sony will, at its option, repair or replace with a new, recertified or refurbished product or part, any product or part determined to be defective.
This Limited Warranty covers only the hardware components packaged with the product. It does not cover separate accessories, technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product, and other included content; any such software or other included content is provided “AS IS” unless expressly provided for in any enclosed software Limited Warranty or End User License Agreement. Please refer to the End User License Agreement(s) included with the product for Your rights and obligations with respect to the software or other included content. If You purchased an extended service plan, please refer to the service plan for the coverage, duration and terms of service. Extended service plans are not governed by this Limited Warranty.
To obtain warranty service , You must deliver the product, in either its original packaging or packaging affording an equal degree of protection to a Sony authorized service center together with a dated purchase receipt in order to obtain warranty service. Sony cannot guarantee that it will be able to repair any product under this warranty or make a product exchange without risk to or loss of software or data. It is Your responsibility to remove or backup any removable media or parts, data, software or other materials You may have stored or preserved on Your product. It Is likely that any media or parts, data, software, or other materials (like pictures, music, videos, etc.) will be lost or reformatted during service and Sony will not be responsible for any such damage or loss. Contact the following for specific instructions on how to obtain warranty service for Your product:
For purchases made in the UNITED STATES:
Visit Sony’s Website: www.sony.com/support
Or call the Customer Experience Center: 1-800-222-SONY (7669)
To register Your product or for contact information to purchase accessories or
parts go to Sony’s Website
For purchases made in CANADA:
Visit Sony’s Website: www.sony.ca/support
Or call the Customer Experience Center: 1-877-899-SONY (7669)
To register Your product or for contact information to purchase accessories or
parts go to Sony’s Website
On-site service for televisions of certain dimensions may be available to a
customer living within a 50km radius of an authorized Sony service facility,
provided the residence can be accessed by an on-road service vehicle.
Repair/Replacement Warranty: This Limited Warranty shall apply to any repair, replacement part or replacement, recertified or refurbished product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is longer. Any parts or product replaced under this Limited Warranty will become the property of Sony. Any replacement, recertified or refurbished product provided under this Limited Warranty may, at Sony’s option, vary in color and/or cosmetic design from the original product and may not include any original engraving or similar customization/personalization.
Sony is not responsible for, and this Limited Warranty does not cover, any damage arising from a failure to operate the product within its intended uses, or otherwise follow the owners manual and safety instructions relating to the product’s use and installation. This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary consumer use. This Limited Warranty does not cover products purchased from sources other than Sony or a Sony authorized dealer (including non-authorized online auctions), or issues due to:
- outdoor exposure and other acts of nature;
- power surges;
- accidental damage;
- abuse;
- limitations of technology;
- cosmetic damage;
- contact with liquid, heat, humidity or perspiration, sand, smoke, or foreign materials;
- use of parts or supplies not sold or authorized by Sony; (
- servicing not authorized or performed by Sony or a Sony authorized service center;
- computer or internet viruses, bugs, worms, or Trojan Horses;
- malfunctions due to peripherals/accessories;
- modifications of or to any part of the product, including “rooting” or other modifications to control the behavior of the product or any factory installed operating system;
- consumable parts such as batteries; or
- any product where the factory-applied serial number has been altered or removed from the product.
Further, to the extent this product incorporates use of a display, please note that a display contains hundreds of thousands of individual pixels, and displays typically contain a small number of pixels that do not function properly. This Limited Warranty does not cover up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
This Limited Warranty does not cover Sony products sold “AS IS” or “WITH ALL FAULTS” or consumables (such as fuses or disposable batteries). Sony will not replace missing components from any package purchased “Open Box” or “AS IS”. This Limited Warranty is valid only in the United States and Canada (as applicable).
LIMITATION ON DAMAGES: SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS PRODUCT. NOR SHALL RECOVERY OF ANY KIND AGAINST SONY BE GREATER THAN THE ORIGINAL PURCHASE PRICE OF THE PRODUCT FROM SONY OR AN AUTHORIZED SONY DEALER.
DURATION OF IMPLIED WARRANTIES OR CONDITIONS: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to You. This Limited Warranty gives You specific legal rights and You may have other rights which vary from jurisdiction to jurisdiction.
For purchases made in the U.S.: Read the following Dispute Resolution/Arbitration provision carefully. It details Your rights and Instructions should a dispute related to the product arise.
What Happens If We Have A Dispute: Should a dispute or claim arise related to the product, Your purchase and/or use of the product, the terms of this Limited Warranty, or any service provided under the terms of this Limited Warranty (including any repair or replacement) (“Dispute”), You and Sony agree that the Dispute shall be resolved exclusively through binding arbitration. YOU UNDERSTAND AND ACKNOWLEDGE THAT BY AGREEING TO ARBITRATION, YOU ARE GIVING UP THE RIGHT TO LITIGATE (OR PARTICIPATE IN AS A PARTY OR CLASS MEMBER) IN ANY DISPUTES IN COURT. You also agree that ANY DISPUTE RESOLUTION PROCEEDING WILL ONLY CONSIDER YOUR INDIVIDUAL CLAIMS, AND BOTH PARTIES AGREE NOT TO HAVE ANY DISPUTE HEARD AS A CLASS ACTION, REPRESENTATIVE ACTION, CONSOLIDATED ACTION, OR PRIVATE ATTORNEY GENERAL ACTION. Despite the above, You have the right to litigate any Dispute on an individual basis in small claims court or other similar court of limited jurisdiction, to the extent the amount at issue does not exceed $15,000, and as long as such court has proper jurisdiction and all other requirements (including the amount in controversy) are satisfied.
Arbitration Instructions. To begin Arbitration, either You or Sony must make a written demand to the other for arbitration. The Arbitration will take place before a single arbitrator. The arbitration will be administered in keeping with the Expedited Procedures of the Commercial Arbitration Rules and the Supplementary Proceedings for Consumer-Related disputes (“Rules”) of the American Arbitration Association (“AAA”), when applicable and in effect when the claim is filed. You may get a copy of AAA’s Rules by contacting AAA at 800-778-7879 or visiting www.adr.org. The filing fees to begin and carry out arbitration will be shared between You and Sony, but in no event shall Your fees ever exceed the amount allowable by the special rules for Consumers Disputes provided for by AAA, at which point Sony will cover all additional administrative fees and expenses. This does not prohibit the Arbitrator from giving the winning party their fees and expenses of the arbitration when appropriate pursuant to the Rules. Unless You and Sony agree differently, the arbitration will take place in the county and state where You live, and applicable federal or state law shall govern the substance of any Dispute during the arbitration. However, the Federal Arbitration Act, 9 U.S.C. § 1, et seq., will govern the arbitration itself and not any state law on arbitration. The Arbitrator’s decision will be binding and final, except for a limited right of appeal under the Federal Arbitration Act.
Opt-Out Instructions. IF YOU DO NOT WISH TO BE BOUND BY THE BINDING
ARBITRATION PROVISION, THEN: (1) You must notify Sony in writing within 30
days of the date that You purchased the product; (2) Your written notification
must be mailed to Sony Electronics Inc., 16535 Via Esprillo, MZ 1105, San
Diego CA 92127, Attn: Legal Department; AND (3) Your written notification must
include (a) Your NAME, (b) Your ADDRESS, (c) the DATE You purchased the
product, and (d) a clear statement that “YOU DO NOT WISH TO RESOLVE DISPUTES
WITH ANY SONY ELECTRONICS ENTITY THROUGH ARBITRATION AND/OR BE BOUND BY THE
CLASS ACTION WAIVER.”
Opting out of this dispute resolution procedure will not affect the coverage
of the Limited Warranty in any way, and You will continue to enjoy the
benefits of the Limited Warranty.
Owner’s Record
The model and serial numbers are located on the rear of the subwoofer.
Record the serial numbers in the space provided below. Refer to them whenever
you call upon your
Sony dealer regarding this product.
Model No. SA-SW3
Serial No. __
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>