SENCOR STM 8950 Stand Mixer Instruction Manual

SENCOR STM 8950 Stand Mixer

Multifunctional Stand Mixer
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.

General warnings

• This appliance may be used by persons with physical, sensory or mental impairments or bLl persons with insufficient experience and knowledge, if they are properly supervised or have been informed about how to use the appliance in a safe manner and understand the potential dangers.
• This appliance may not be used by children. Keep the appliance and its power cord away from children.
• Children must not play with the appliance.
• Cleaning and maintenance performed by the user must not be performed by unsupervised children.
• In the event that the power cord is damaged, have it repaired at a professional service center to prevent causing a dangerous situation. It is forbidden to use the appliance if it has a damaged power cord.

Warning
Incorrect use may lead to injuries.

• Pa increased attention not to injure yourself on the sharp parts when handling the grinding blade of the grinder, grating cones, and the blade assembly of the blending jar, especially when installing and removing accessories, when filling or emptying the blending jar, and when cleaning.
• The surfaces of the appliance and its accessories that come into contact with food must always be cleaned according to the instructions in this user’s manual.
• This user’s manual includes processing times and speed settings for the individual types of accessories.
• Always turn off the appliance, disconnect it from the power socket when not using it, when leaving it without supervision, and before assembling, disassembling, cleaning or moving it.
• Before replacing the accessories or accessible parts that move during use, turn the appliance off and disconnect it from the power supply.

Electrical safety

• Before connecting this appliance to an electrical power socket, make sure that the voltage stated on its rating label corresponds to the voltage in your power socket.
• Connect the appliance only to a properly grounded socket. Do not use an extension cord.
• Fully unwind the power cord before use.
• Ensure that the power plug contacts do not come into contact with water or any other liquid.
• Do not disconnect the appliance from the power socket by pulling on the power cord. This could damage the power cord or the power socket. Disconnect the cord from the power socket by gently pulling the plug of the power cord.
• Do not connect and disconnect the appliance’s power plug to and from the power socket with wet hands.
• Do not place any items on the power cord. Make sure the power cord does not hang over the edge of a table and that it is not touching a hot surface or sharp objects.
• Keep the power cord dry.
• Do not wind the power cord around the appliance.
• To avoid the danger of injury by electrical shock, do not repair the appliance yourself or make any adjustments to it. Have all repairs or adjustments of the appliance performed at an authorised service centre. Tampering with the appliance during the warranty period may void the warranty.
• To prevent the risk of injury by electrical shock, never submerge the appliance nor its power cord in water or any other liquid, or wash these under running water.
• Always turn off the appliance and disconnect it from the power socket when you have finished using it.
• In the event that the appliance falls into water, under no condition continue using it. Hand it over to an authorized service center for inspection. The appliance is not intended for operation by means of an external timer switch or any other component that switches the appliance on and off automatically.

Safety during use

• The appliance is designed for household use and is constructed for processing the usual amount of food in a household. Do not use it for commercial purposes or for purposes other than those for which it is intended.
• This appliance is designed for use in indoor areas only. Never use it in industrial surroundings or outdoors.
• Only use the appliance with the original accessories from the manufacturer.

Warning
Using non-original accessories may result in a dangerous situation arising.

• It is forbidden to modify the surface of the appliance in any way, e.g. with self-adhesive wallpaper, foils, etc.

• Only use the appliance and its accessories in accordance with the instructions contained in this user’s manual.

• Before first use, it is necessary to thoroughly wash the individual parts of the removable accessories using warm water and kitchen detergent, then rinse them with drinking water and wipe them thoroughly until dry using a wiping cloth.

• When cleaning the blending jar, make sure that no water enters into the underside of the blending jar that is connected to the multifunctional stand mixer. Never rinse the multifunctional stand mixer or its power cord underwater or submerge it in water.

• Before attaching the removable accessories to the appliance, make sure that they are dry.

• When tilting down the multi-function head, pay increased attention not to crimp your fingers between the tilting and rigid part of the multifunctional stand mixer.

• Before every use, check the selected accessory for damage. Never use the appliance with a damaged accessory.

• Do not cover the appliance’s vents.

• Do not place the appliance nor its accessories on an electric or gas stove or in its vicinity, on the edge of a table or on an unstable surface. Do not place the appliance nor its accessories near heaters, open fires or other sources of heat. Only

• place the appliance on a clean, even, dry and stable surface.

• Do not use the appliance when it is not functioning correctly or alter it has fallen on the floor, been submerged in water or is damaged in any other way. Hand it over to an authorized service center for inspection or repair.

• Do not expose the appliance and its accessories to the outdoor environment, extreme temperatures, direct sunlight, excessive humidity or excessively dusty environments.

• Before putting the appliance into operation, check that it is properly assembled, and that the multi-function head is in the horizontal position. When using an accessory that is intended for beating, kneading or whipping, ensure that it is submerged in the stainless steel bowl with the ingredients.

• Do not turn on the appliance when it is empty. Incorrect use of the appliance may negatively affect its lifetime.

• When handling the appliance, ensure that your hands are clean and dry.

• To prevent a dangerous situation from arising, prevent coming into contact with the rotating parts of the appliance. While using it, never place hands, forks or any other utensils into the bowl with the ingredients, and keep hair, clothing, etc. at a sufficient distance from the rotating parts of the appliance. If a fork or another utensil falls into the container while the appliance is running, immediately turn it off and disconnect it from the power socket.

• Make sure that no hair, clothing or other items enter the feed tube of the meat grinder or grater while it is running. Do not put anything other than the ingredients that are to be processed into the feed tube.

• Never use your lingers or other items to push ingredients through the feed tube of the meat grinder or the grater. For this purpose there is
  a pusher that is included as an accessory to this appliance.

• Never tilt open the multi-function head during operation.

• Before attaching an accessory to the appliance, removing or replacing it, always turn oil the appliance and disconnect it from the power socket.

• Never assemble or disassemble an accessor!:J while it is mounted on the appliance.

• Never start the blender without the lid properly seated in position. During operation, the lid must always be properly attached to the blending jar.

• Hot steam or splattering hot foods or liquids may cause scalding. Always pay increased attention when handling hot liquids and foodstuffs.

• The glass blending jar is resistant to heat up to 55 °C. Never place food or pour any liquids with a higher temperature into it, otherwise, there is a risk of the glass jar cracking, which may subsequently lead to scalding.

• For reasons of increased safety, allow hot foods and liquids to cool down before putting the appliance into operation.

• When processing warm liquids in the blending jar, do not remove the inner cap of the blending jar during operation.

• The surfaces of the accessories that are used may be hot after use. Do not touch the hot surface. When carrying the blending jar or the stainless steel bowl use the handle or holders intended for this purpose.

• No accessories of this appliance are intended for use in a microwave or electric oven, etc.

• To prevent injury caused by sharp edges, be especially careful when handling the grinding blade of the meat grinder, the grating and slicing cones, and the blade assembly of the blender. Increased attention must also be paid when emptying out the blending jar, when assembling the meat grinder, when removing the grinding blade from the grinding chamber, when assembling or disassembling the grating cones and when cleaning.

• In order to prevent a dangerous situation from arising, never use the appliance to process hard ingredients such as, for example, walnut shells, hard stones of apricots, peaches, mangoes, etc.

• The maximum continuous operating time of the appliance is 10 minutes. When using the blender, do not exceed the operating time of
  3 minutes. Before using it again, allow the appliance to cool down for 30 minutes. Do not exceed the maximum continuous operating time and adhere to the time necessary for the cooling down of the appliance before further use.

Safety during cleaning and maintenance

• Before cleaning, always turn oil the appliance, disconnect it from the power socket and allow it to cool down completely.
• Regularly clean the appliance alter each use according to the instructions in chapter Cleaning and Maintenance. Do not perform any maintenance on the appliance except for cleaning as described in this user’s manual.
• Do not wash the multi-function head or the base unit under running water or submerge it in water or another liquid. Neither the appliance nor its accessories are intended for washing in a dishwasher.
• Store the appliance in a dry, clean environment. Before storing the appliance, check that the multi-function head is tilted down to the horizontal position.

Multifunctional Stand Mixer

User’s manual

• Thank you for purchasing a SENCOR brand product and we hope that you will be happy with it.
• Prior to using this appliance, please read the user’s manual thoroughly, even in cases, when one has already familiarised themselves with previous use of similar types of appliances. Only use the appliance in the manner described in this
• user’s manual. Keep this user’s manual in a safe place where it can be easily retrieved for future use. In the event that you hand this appliance over to somebody else, make sure to also include this user’s manual.
• Carefully unpack the appliance and take care not to throw away any part of the packaging before you find all its parts.
• We recommend saving the original cardboard box, packaging material purchase receipt and responsibility statement of the vendor or warranty card for at least the duration of the legal liability for unsatisfactory performance or quality. In the event of transportation, we recommend that you pack the appliance in the original box from the manufacturer.

DESCRIPTION DF THE APPLIANCE AND ACCESSORIES

1. A1 T ilting multi-function head with the illumination of the stainless steel bowl area
2. A2 Button for releasing the meat grinder from the front attachment hub on the head
3. A3 Removable cover of the front attachment hub for the meat grinder / grating attachment
4. A4 Front attachment hub for the meat grinder / grating attachment
5. AS Hole for attaching the whisk, beater or kneading hook
6. AS Base for the stainless steel bowl
7. A7 Top blender attachment hub
8. AS Removable cover of the top blender attachment hub
9. A9 Control panel with display
10. A10 Multi-function head lock/ release lever
11. A11 Speed control knob serves to set the speed level and to stop operation of the appliance in the manual setting mode
    • 0 – stop the appliance
    • 1-8 – speed levels
    • 1 – lowest, 8 – highest)
    • P – PULSE mode for increasing the speed to maximum for a short time.
12. A12 Anti-slip feet
13. A13 Stainless steel bowl for processing food with a total capacity of 6.71 (2 pcs) The maximum filling capacity of the stainless steel bowl is 4.5 I.
14. A14 Transparent lid against the splashing of ingredients with a hole for the gradual addition of ingredients into the stainless steel bowl
15. A1S Beater
16. A1S Balloon whisk
17. A17 Kneading hook
18. A1S Stainless steel bowl lid (2 pcs) serves to cover the stainless steel bowl A13 when you wish to temporarily keep your processed ingredients in it.
19. A19 Flexi-beater with spatulaIt is used in the sameway as the beater A1S.

It is fitted with a spatula, which gradually wipes the wall of the stainless steel bowl whereby it achieves better processing of all the ingredients into the prepared mixture.

Control panel with display

1. B1 Operating time indicator

2. shows the set, elapsed and remaining operating time

3. B2 Reduce operating time button

4. B3 Increase operating time button

5. B4 Speed indicator

6. BS Touch button for starting/ stopping the preset program for whipping with the balloon whisk

7. BS Touch button for starting/ stopping the preset program for beating with the beater

8. B7 Touch button for starting/ stopping the preset program for kneading with the kneading hook

9. BS Touch button for starting/ stopping the preset program  for the blender

10. B9 Touch button RESET
    Meat grinder
    

    • C1 Grinding chamber

    • C2 Feed tube

    • C3 Screw shaft insertion hole C4 Hopper

    • cs Pusher

    • cs Screw shaft

    • C7 Grinding blade

    • cs Fine grinding plate

    • C9 Medium fine grinding plate
      *Grating attachment
      **

    • D1 Pusher
      D2 Grater insertion chamber

    • D3 Very fine grating cone

    • D4 Screw ring for securing the grating cone inside the chamber
      

11. B10 Start/Pause touch button CID Coarse grinding plate

12. C11 Screw ring

13. C12 Separator

14. C13 Kibbeh attachment

15. C14 Conical attachment

16. C1S Sausage stuffer attachment

17. C1S Cookie maker holder

18. C17 Cookie maker

    • DS Coarse grating cone
    • DS Grater for making slices
    • D7 Fine grating cone
    • DS Feed tube

• Accessory not included. Can be purchased separately.

Blender

1. E1 Inner cap
2. E2 Outer lid with a hole for adding ingredients
3. E3 Blending jar with 1.51  capacity
4. E4 Blade assembly is an integral part of the blending jar
5. ES Base for mounting/removing the blender from the top attachment hub of the head

INTENDED USE OF THE APPLIANCE

• The Multifunctional Stand Mixer is intended for processing a standard amount of food in the household. It is suitable for beating, whipping and kneading and blending of ingredients, for meat grinding, for making kibbeh or sausages, grating food and making cookies.

BEFORE FIRST USE

• Clean the external surface of the multifunctional stand mixer using a lightly dampened wiping cloth and then take care to prevent any moisture from entering the speed control knob A11.
• Clean the front attachment hub A4 for mounting the grinder or the grating attachment and the top attachment hub A7 for mounting the blender using only a dry wiping cloth.
• Only clean the power cord of the multifunctional stand mixer using a dry wiping cloth.

Warning :
Never rinse the multifunctional stand mixer or its power cord under water or submerge it in water.

• Prior to first use, clean all the parts that are intended for coming into contact with food in the following manner:
• Thoroughly wash the stainless steel bowl A13, lid A1S, transparent lid A14, attachments A1S, A1S, A17, and A19, parts of the grinder C1-C17, the parts for grinding D1-DS and the blender accessories E1-E2 in warm water using a neutral kitchen detergent. Then rinse these parts with clean water and allow them to dry naturally or drw them out using a wiping cloth.
• ThoroughlW rinse out the internal area of the blending jar E3 with warm water using neutral kitchen detergent and then rinse it out several times with clean water. Rinse the outer surface of the glass blending jar E3 under warm running water whilst using neutral kitchen detergent and then wash under clean running water.

Attention: When cleaning, make sure that no water enters into the underside of the blending jar ES bw which it is connected to the multifunctional stand mixer. Carefully dry any moisture or always allow it to drw out completely. Allow the internal area of the blending jar E3 to drw out completely and drw the outer surface of the glass blending jar E3 using a wiping cloth.

Attention
NEITHER the multifunctional stand mixer NOR any parts of its accessories are designed to be washed in a dishwasher! When cleaning the internal area of the blending jar E3, inside of which the blade assembly E4 is located, and when cleaning the grinding plates shalt C8-C10, CS and grinding graters blade D3, C7, DS-D7 grinder paw screw increased attention so as not to injure yourself on the blades or sharp edges.

INSTALLATION LOCATION OF THE APPLIANCE

• Place the appliance on an even, dry, clean and especially stable surface, for example on a kitchen countertop.
• Always locate the appliance so that nobody can brush against it and thereby pull or push it over. Never locate it on the edge of the countertop or table, the vibrations during use could cause it to move resulting in a subsequent fall.

TURNING ON AND OFF

Before connecting the multifunctional stand mixer to a power socket, always check that it is correctly assembled according to the instructions in this user’s manual( that the multi-function head Al is Afl tilted down into  the horizontal position and that the speed control knob is set to the
0 position.
Connect the power cord to an el. power socket. A sound signal control knob and the illumination of the stainless steel bowl area will be lit for a moment and then turn off. The control button
B10 00 will subsequently repeatedly turn on and off.
Touch button B10 ( ) 00 to set the multifunctional stand mixer to e stand-bw mode. The appliance will beep, the buttons BS-B9, the speed control knob A11 and the illumination of the stainless steel bowl area will be lit. Subsequently, buttons BS-BB will repeatedly turn on and oil. The stainless steel bowl area, the buttons B9-B10 and the speed control knob A11 will remain lit.

Note :
If no settings are made within 10 minutes of putting the multifunctional stand mixer into the stand-bw mode, the control panel with display A9, the speed control knob A11 and the illumination of the stainless steel bowl will turn off. Dnlw button B10 ( ) 00 will remain active. If this happens, simply touch button B10 () 00 to put the multifunctional stand mixer back into the stand-bw rnode.

• To put the multifunctional stand mixer into operation from the stand-bw mode, use the control elements described further in this user’s manual. Read the entire user’s manual before putting the multifunctional stand mixer into operation. It is necessary to adhere to the instructions contained in this user’s manual during operation. The purpose and method of use of the individual types of accessories are described in the respective chapters.
• To stop operation, use the respective control elements. In the event that wou have selected one of the preset programs, operation will be stopped automatically at the end of the preset program.
• When wou have finished using the multifunctional stand mixer, ensure that it is turned off and that the control knob A11 is set to the 0 position. Then disconnect the multifunctional stand mixer from the electrical power socket.

CONTROL ELEMENTS

SOFT START FUNCTION

This food processor has a soft start function that ensures a smooth ramp up of the motor when it starts, whereby it is gentle of the internal components of the product and extends its lifetime.

MOTOR PROTECTION

• The motor of the multifunctional stand mixer is equipped with a safety mechanism that protects it against damage in the situation where the multifunctional stand mixer is subjected to an excessively high load or if it remains in operation for too long. In the event that such a situation occurs, the safety mechanism will be triggered and the operation of the multifunctional stand mixer will be stopped. Set the control knob A11 to the D position, disconnect the power cord from the power socket and allow the multifunctional stand mixer to cool down for at least 30 minutes.
• Do not leave the multifunctional stand mixer in operation for too long under a high load. Separate large batches into several smaller batches.

BEATING, WHIPPING AND KNEADING

Warning :
Before installing or removing accessories, the multifunctional stand mixer must always be turned off and disconnected from the power socket.
When installing or removing an attachment to/from the multi-function head A1, whilst the multifunctional stand mixer is connected to the power grid, it could happen that it is accidentally turned on and cause serious injury.

Planetary mixing system

• The multifunctional stand mixer is equipped with a planetary mixing system, which works on the principle of a dual rotation of the attachment. The attachment rotates anticlockwise along the inner perimeter of the bowl while rotating around its own axis in the opposite direction. This ensures that ingredients inside the stainless steel bowl are processed thoroughly and evenly.

Selecting an attachment type

Mounting attachments and attaching the stainless steel bowl (fig. F)

• Make sure that the control knob A11 is set to the D position and that the multifunctional stand mixer is disconnected from the power socket. Covers AB and A3 must be attached in their place.

Note
The multifunctional stand mixer is equipped with a safety mechanism that prevents it from being started unless the cover AS is properly mounted in place.

• Using one hand, push down the lever A1O towards the open padlock symbol. This will release the multi-function head A1. With the other hand, hold the multi-function head A1 from above. Release the lever A1O and tilt the multi-function head A1 all the way up. Locking of the multi-function head A1 in the tilted up position is indicated by the lever A1O returning to the default position (to the closed padlock swmbol), which is accompanied bw an audible click.
• Insert the stainless steel bowlA13 into the base unit AS and secure it in place by turning it clockwise When the stainless steel bowl A13 is properly attached, it cannot be separately lifted out of the base unit AS.
• Select the attachment A15, A1S, A17 or A19 based on its intended use, insert it into the hole AS in the multi-function head A1 and turn it anticlockwise to secure it in place. Lightly pull the attachment downwards with one hand to check that
• it is properly attached.
• Fill the stainless steel bowlA13 with the ingredients that you wish to process. Proceed as described in chapter Adding ingredients into the bowl.
• Using one hand, push down the lever A1O and the other to slowly tilt down the multi-function head A1, whilst releasing the lever A1O. Alter tilting down the multi-function head A1 into the horizontal position, there will be an audible click and the lever A1O will return to the horizontal position (to the closed padlock symbol). Thereby the multi-function head A1 is locked in the work position.

Attention
When tilting down the multi-function head A1, take care not to crimp your fingers between the tilting and rigid part of the multifunctional stand mixer.
Put the transparent cover A14 on to the stainless steel bowl A13 so that the feed tube points towards the front part of the multi-function head A1.

Adding Ingredients Into the bowl

• Put the ingredients that you wish to process into the stainless steel bowlA13. Do not fill the stainless steel bowl A13 above the maximum mark, i.e. 4.5 litres.
• If an insufficient amount of ingredients are put in the bowlA13 then they may not be optimally processed.
• The minimum and maximum amounts of ingredients that can be processed in a single batch are specified in the following table. Various recipes may include various ratios of powder (loose) and liquid ingredients, and therefore it is also necessary to take the overall composition of the given recipe into consideration.

Operation of the multifunctional stand mixer with the kneading hook. beater or whisk

• Before connecting the multifunctional stand mixer to a power socket, always check that it is correctly assembled according to the instructions in this user’s manual, that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the O position.

• Connect the power cord to an el. power socket. Touch button B10 ( ) 00 to set the multifunctional stand mixer to standby mode.

Preset programs

• The multifunctional stand mixer is equipped with three preset programs: beating, whipping and kneading.
• In the stand-by mode, start the work cycle with a preset speed and duration by touching the button of one of the preset programs. The following buttons will be lit: B9-B1D, the button of the currently selected program, speed indicator B4 (the current speed is indicated by flickering speed indicators); and the remaining countdown time of the preset time will be shown on the display.

Note

It is not possible to adjust the speed in a preset program. The time can be adjusted on the control panel using buttons B2 The maximum times that can be set are as follows: 04:00 in the whipping program, 06:00 in the beating program and 08:00 in the kneading program.

• If you wish to pause a program, press button B10 ( ) 00. Pressing the B10 ( ) 00 button again will resume the program. The memory function enables the program to be started again up to 10 minutes from it being paused. After 10 minutes, the display with the control
• panel A9 will turn off. Only button B10 ) 00 will remain active on the control panel.
• If you wish to end a program prematurely, press button B9 RESET or the button with which you started the program.
• When the program is finished, the multifunctional stand mixer will beep and will stop operation, and it will switch to the stand-by mode.

Warning :
Never insert items such as spoons, kitchen knives, forks, etc. into the stainless steel bowl A13 during operation as this could result in serious injury or damage to the appliance.

Manual setting

• If you do not wish to use the preset programs, you can set the processing speed and duration yourself.
• You can change the speed setting while the appliance is running. We recommend to always first start with a lower speed setting and to then gradually increase it as required. We recommend that runny doughs are processed at a lower speed; this will prevent ingredients from splashing out. As soon as they are mixed together, increase the speed to the required level. The recommended food processing times and recommended speed settings are provided in the table
• Quick guide to processing ingredients.

Speed setting

• Turning the speed control knob A11 to the required speed level will start the multifunctional stand mixer. The display A9 will show the elapsed time of operation.
• The processing time for most ingredients is generally in the order of several minutes. When using the whisks, we recommend that you do not exceed the operating time of 4 minutes, when using the beaters 6 minutes and when using the kneading hooks 8 minutes.
• To stop the appliance, set the control knob A11 to the O position. This will switch the multifunctional stand mixer to the standby mode. The multifunctional stand mixer will automatically stop after 10 minutes of operation unless you set the control knob A11 to the 0 position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the O position.

Setting the speed and time of operation
Turning the speed control knob A11 to the required speed level will start the multifunctional stand mixer. The display A9 will start counting down the elapsed time of operation.

Use buttons B2 to set the desired time of operation. The maximum operating time that can be set is 10 minutes. The display A9 will show the time remaining until the set time has elapsed. When the set time has elapsed, the multifunctional stand mixer will beep, stop automatically and switch to the standby mode.

• Set the speed control knob A11 back to the 0 position.

Attention

The maximum continuous operating time is 10 minutes. Then allow the appliance to cool down for approximately 30 minutes.

Pulse level

• If you wish to increase the speed to maximum for a short time, turn the control knob A11 to position P (pulse mode) and hold it for a short time in this position. As soon as you release the control knob A11, it will automatically return to the 0 position. Hold the control knob A11 in the P position only for short intervals of a few seconds in duration.

Quick guide to processing Ingredients

Note

The speeds and processing times provided above are only a reference. To prevent ingredients from splattering out of the stainless steel bowlA13, select an initial speed level of 1 or 2. Later set a higher speed based on requirements. For easier mixing of dough we recommended soft margarine or butter.
When whipping egg whites, the stainless steel bowl A13 and the whisk A1S must be perfectly clean and dry. Even a small amount of lat may result in that the egg whites will not be whipped to the desired snowy consistency. Whipping cream should be cooled to a temperature of 6 °c prior to being whipped. Prior to processing them, allow the ingredients used for making various doughs to rest at room temperature.

Removing or releasing stuck-on ingredients

• In the event that it is necessary to remove ingredients or if the ingredients (e.g. dough) are stuck on the sides of the bowlA13
  and it is necessary to release them, stop the operation of the appliance by touching the button RESET B9 (on preset programs) or by setting the speed control knob A11 to the 0 position (manual setting).

• Attention: Ending the operation of the appliance will cancel all previous settings.

• Make sure that the control knob A11 is set to the 0 position and disconnect the multifunctional stand mixer from the power socket.

• In the event that the cover Al4 was used, first take it off. Tilt open the multi-function head A Check that it is properly locked in the top open position and remove the ingredients as necessary. If ingredients are stuck to the bowl use a

• standard kitchen spatula to wipe them off the edge of the bowl A13.

• Check that there are only ingredients that you wish to process located inside the stainless steel bowl A13. Tilt the multi-function head Al back down into the working position. Put the cover Al4 on to the bowlA13. Connect the multifunctional stand mixer to a power socket and set the settings as required.

Ending operation and disassembling the accessories

• Alter you have finished using the appliance, set the control knob Afl to the 0 position and disconnect the power cord from the power socket.
•  you have used the transparent bowl cover A14, take it oil.
• Using one hand, push down the lever A1D towards the open padlock symbol. This will release the multi-function head A At the t same time, with the other hand, hold the multi-function head Al  from above. Release the lever AID and tilt the multi-function head A1 all the way up. Locking of the multi-function head Al in the tilted up position is indicated by the lever A1D returning to the default position (to the closed padlock symbol), which is accompanied by an audible click.
• Gently push the attachment that you used upwards towards the multi-function head A1 and simultaneously turn it clockwise. This will release it and you can take it out of the multi-function head At
• Turn the stainless steel bowl A13 anticlockwise and carefully remove it from the base unit AS.
• Set the multi-function head A1 back to the horizontal position.
• Clean out the used accessories after each use according to the instructions in chapter CLEANING AND MAINTENANC E.

GRINDING MEAT. MAKING KIBBEH. STUFFING SAUSAGE CASINGS AND MAKING

COOKIES

Warning :
Before installing or removing accessories, the multifunctional stand mixer must always be turned off and disconnected from the power socket.
When installing or removing a grinder to the multi­function head A1, whilst the multifunctional stand mixer is connected to the power grid, it could happen that it is accidentally turned on and cause serious injury.

Assembling the grinder for grinding meat (fig, C and C,)

Insert the screw shalt CS into the grinding chamber Ct At the same time make sure that the screw shalt CS is inserted in the grinding cha, ber C1 in the correct direction and that it fits in properly.
Place the grinding blade C7 on to the shalt CS with the edge lacing outwards from the chamber C1 and on to it attach a grinding plate CB, C9 or CID depending on the preferred consistency the grind. Make sure that the grinding plate properly slides along the perimeter into the hole in the grinding chamber Cl.

Warning
When handling the grinding blade C7 and the grinding plates CB, C9 or CID, pay increased attention so as not to injure yourself on the sharp parts.

• Place the screw ring C11 on to the grinding chamber C1 and tighten it securely by screwing it in.

Assembling the grinder for making kibbeh (fig. C and C,)

• Insert the screw shaft CS into the grinding chamber Cl. At the same time make sure that the screw shalt CS is inserted in the grinding cha,;,ber Cl in the correct direction and that it lits in properly.
• Place the kibbeh attachment C13 on to the shalt CS and make sure that along the perimeter it properly slides into the hole in the grinding chamber Cl. Put the conical attachment Cl4 on to the kibbeh attachment C13.
• Complete the assembly by screwing the screw ring C11 on to the grinding chamber Cl. Pull the screw ring C11 tight with appropriate force.

Assembling the grinder for stuffing sausage casings (fig. C and C,)

• Insert the screw shaft CS into the grinding chamber Ct At the same time, make sure that the screw shaft CS is inserted in the grinding chamber C1 in the correct direction and that it fits in properlw.
• Place the separator C12 on to the shaft CS and make sure that along the perimeter it properly slides into the hole in the grinding chamber C1. Put the sausage stuffer attachment C1S on to the separator C12.
• Complete the assemblw bw screwing the screw ring C11 on to the grinding chamber C1. Pull the screw ring C11 tight with appropriate force.

Assembling the grinder for making cookies (fig. C and C4)

• Insert the screw shaft CS into the grinding chamber C1. At the same time, make sure that the screw shaft CS is inserted in the grinding chamber C1 in the correct direction and that it fits in properlw.
• Place the separator C12 on to the shaft CS and make sure that along the perimeter it properlw slides into the hole in the grinding chamber C1. Insert the cookie maker holder C1S into the screw ring C1t
• Screw the screw ring C11 together with the cookie maker holder C1S on to the grinding chamber C1. Pull the screw ring C11 tight with appropriate force.
• Complete the assemblw bw inserting the cookie maker C17 into the holder C1S.

Mounting the assembled grinder on to the multifunctional stand mixer (llg.G-J)

Make sure that the control knob A11 is set to the D position and that the multifunctional stand mixer is disconnected from the power socket. The multi-function head A1 must be tilted down to the horizontal position and none of the attachments A1S, A1S, A17 or A19 maw be mounted on it. Cover AS must be attached in its place.

Note :
The multifunctional stand mixer is equipped with a safetw mechanism that prevents it from being started unless the cover AS is properly mounted in place.

• Remove the front cover A3 from the multi-function head At To remove the front cover A3, it is necessary to push down the bottom part of the cover A3 with wour index finger, which will release it and then it can be taken off bw pulling it upwards.
• Put the assembled grinder on to the front hub A4 at an angle of approximately 45° and turn it anticlockwise all the waw to secure it in the operating position.
• Put the stainless steel hopper C4 on to the feed tube of the grinder C2, and place a suitable container for collecting the food underneath the grinder. You can use the stainless steel bowlA13. When using the kibbeh maker attachment or the cookie maker attachment, we recommend using a tray.

Mincing meat

• First prepare the rneat for grinding in the following waw: Remove all bones, tendons, cartilage and cut the meat into 2 x 2 x 6 cm size pieces that will freelw pass through the feed tube C2.

Warning:
Do not process frozen meat. Allow it to defrost before grinding it.

• Before connecting the multifunctional stand mixer to a power socket, alwaws check that it is correctly assembled according to the instructions in this user’s manual, that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the D position.
• Connect the power cord to an el. power socket. Touch button 810 () 00 to set the multifunctional stand mixer to standby mode.
• Use the control knob A11 to set the desired speed. For meat grinding, it is recommended to set speed level 4. Always initially set the lowest speed and then increase it as required. The displaw will show the elapsed operating time.
  Gradually place the rneat pieces into the feed tube C2 and push them in using the pusher CS. Take care not to clog up the feed tube C2 bw a large amount of meat. Do not process more than 5 kg of meat per batch. The processing time is only several minutes.

Warning
Never use fingers or other items to push the meat in. For this, always use the provided pusher CS.

• Ground meat will fall into the container located underneath the grinder. The meat that remains in the grinding chamber C1 can be removed by grinding a slice of bread or a bread roll.
• To stop the appliance, set the control knob A11 to the D position.
• The multifunctional stand mixer will automatically stop after  10 minutes of operation, unless wou turn it off bw setting the control knob A11 to the 0 position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the D position.

Making kibbeh

• Prepare a pre-ground kibbeh meat mixture and place it on to the hopperC4.
• Before connecting the multifunctional stand mixer to a power socket, alwaws check that it is correctly assembled according to the instructions in this user’s manual that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the D position.
• Connect the power cord to an el. power socket. Touch button 810 ( ) 00 to set the multifunctional stand mixer to stand-bw mode.
• Use the control knob A11 to set the desired speed. For making kibbeh, it is recommended to set speed level 4. Alwaws initially set the lowest speed and then increase it as required. The displaw will show the elapsed operating time.
• Graduallw place the pre-ground rneat mixture into the feed tube C2 and push it in using the pusher CS. The result will be a hollow rneat tube that is then cut into smaller pieces. The kibbeh is a traditional meal from the Middle East made predominantly from ground meat and whole-grain wheat.

Warning :
Never use fingers or other items to push the meat mixture in. For this, alwaws use the provided pusher CS.

To stop the appliance, set the control knob A11 to the D position.
The multifunctional stand mixer will automatically stop after 10 minutes of operation, unless wou turn it off bw setting the control knob A11 to the D position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the D position.

Stuffing sausage casings

• Prepare a sausage casing that wou will stuff with pre-ground meat and allow it to soak in lukewarm water for approx. 10 minutes. Place the ground rneat mixture on to the hopper C4. Take the sausage casing out of the water and skewer or tie up one end and slide the other end like a sock on to the sausage stuffer attachment C1S .
• Before connecting the multifunctional stand mixer to a power
• socket, alwaws check that it is correctlw assembled according to the instructions in this user’s manual, that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the D position.
• Connect the power cord to an el. power socket. Touch button 810 ( ) 00 to set the multifunctional stand mixer to stand-by mode.
• Use the control knob A11 to set the desired speed. For stuffing sausage casings, it is recommended to set speed level 4. Alwaws initially set the lowest speed and then increase it as required. The displaw will show the elapsed operating time.
• With one hand hold the sausage casing on the attachment C1S and use the other hand to push the ground meat mixture with the pusher CS through the feed tube of the grinder C2. If the sausage casing sticks to the attachment C1S, it is necessary to moisten it with water again.

Warning
Never use fingers or other items to push the meat mixture in. For this, always use the provided pusher CS.

• To stop the appliance, set the control knob A11 to the D position.
• The multifunctional stand mixer will automatically stop after10 minutes of operation, unless you turn it off by setting the control knob A11 to the D position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the D position.

Making cookies

• Place the prepared dough on to the hopper C4.
• Slide the cookie maker C17 to the left or right to set the desired cookie shape.
• Before connecting the multifunctional stand mixer to a power socke, always check that it is correctly assembled according to the instructions in this user’s manual that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the D position.
• Connect the power cord to an el. power socket. Touch button B10 I> 00 to set the multifunctional stand rnixer to stand-by rnode.
• Use the control knob A11 to set the desired speed. For making cookies, it is recommended to set speed level 3-4. Always initially set the lowest speed and then you can increase it as required. The display will show the elapsed operating time.
• Use the pusher CS to push the dough through the feed tube C2. The result will be a dough having the shape that you set using the cookie maker C17. We recommend that you place a tray or your palm underneath the pushed out dough.
• Then cut the formed dough into smaller pieces.

Warning
Never use fingers or other items to push the dough in. For this, always use the provided pusher CS.

• To stop the appliance, set the control knob A11 to the D position.
• The multifunctional stand mixer will automatically stop after 10 minutes of operation, unless you turn it off by setting the control knob A11 to the D position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the D position.

Ending operation and disassembling the grinder

• After you have finished using the appliance, set the control knob A11 to the D position and disconnect the power cord frorn the power socket.
• To remove the meat grinder from the multifunctional stand mixer, first remove the hopper C4. Then press the button A2, turn the grinder clockwise and pull it upwards from the multi-function head A1 to remove it. After removing the grinder, put the front attachment hub cover A3 back in its place.
• When disassembling the meat grinder into its individual parts, proceed in the reverse sequence.
• Clean out the used accessories after each use according to the instructions in chapter CLEANING ANO MAINTENANCE.

GRATING

Warning
Before installing or removing accessories, the multifunctional stand mixer must always be turned off and disconnected from the power socket.
When installing or removing a grating attachment to the multi-function head Al, whilst the multifunctional stand mixer is connected to the power grid, it could happen that it is accidentally turned on and cause serious injury.

Assembling the grating attachment (fig. DJ

Insert one of the grating cones D3, DS, D6 or D7 into the chamber D2. Then make sure that the grating cone is inserted into the chamber D2 in the correct direction and that it properly fits into chamber D2. For advice about the choice of grating cone, see Quick guide to selecting a grating cone

Attention
When inserting grating cone D3, DS, D6 or D7 into the chamber D2, pay increased attention so as not to injure yourself on the sharp edges.

• Secure the grating cone in the chamber D2 by screwing the screw ring D4 on to the front part of the chamber D2. Pull the screw ring D4 tight with appropriate force.

Mounting the assembled grating attachment on to the multifunctional stand mixer (fig. K

Make sure that the control knob A11 is set to the D position and that the multifunctional stand mixer is disconnected from the power socket. The multi- function head A1 must be tilted down to the horizontal position and none of the attachments A1S, A16, A17 or A19 may be mounted on it. Cover AS must be attached in its place.

Note
The multifunctional stand mixer is equipped with a safety mechanism that prevents it from being started unless the cover AS is properly mounted in place.

• Remove the cover A3 from the multi-function head At To remove the front attachment hub cover A3, first push down the bottom part of the cover A3 with your index finger, which will release it and then take it off by pulling it upwards.
• Put the assembled grating attachment on to the front hub A4 at an angle of approximate! 45° and turn it anticlockwise all the way to secure it in the operating position.
• Place an appropriate food container beneath the grating attachment. You can use the stainless steel bowl A13.

Using the grater

• The grater is intended for processing various types of fruit, vegetables and other foods normally used in the household.
• Prepare the ingredients and cut them into pieces that will pass through the top feed tube DS. Certain types of fruits /vegetables will require stones, pits, hard peels, shells, etc. to be removed before being processed.

Attention

Never attempt to process nut shells or hard fruit stones.

• Before connecting the multifunctional stand mixer to a power socket, always check that it is correctly assembled according to the instructions in this user’s manual that the multi-function head A1 is tilted down into the horizontal position and that the speed control knob A11 is set to the D position.
• Connect the power cord to an el. power socket. Touch button B10 ( ) 00 to set the multifunctional stand mixer to standby mode.
• Use the control knob A11 to set the desired speed. For the grating attachmen, it is recommended to set speed level 6. Always initially set the lowest speed and then increase it as required. The display will show the elapsed operating time.
• Place the ingredients one by one into the feed tube DB. Use the supplied pusher DI to push ingredients through the feed tube DB. The processing time is only several minutes.

Warning
Never use fingers or other items to push the ingredients in. For this, always use the provided pusher DI.

• Always insert the individual pieces of ingredients into the feed tube, and with appropriate force gently push down on the pusher DI. During operation, ensure that the ingredients are passing through the attachment by looking into the feed tube DB. Never fill the feed tube up to its top edge with ingredients. Processing large amounts of ingredients at once may overload the multifunctional stand mixer. The grated ingredients will fall into the container located beneath the grating attachment.
• To stop the appliance, set the control knob A11 to the O position.
• The multifunctional stand mixer will automatically stop after 10 minutes of operation, unless you turn it off by setting the control knob A11 to the O position. In the event that automatic shut-off occurred, set the speed control knob A11 back to the O position.

Useful advice for grating

• To achieve the best possible results, process fresh not overly ripened fruit. The same applies to vegetables.
  Softer types of fruit can be put into the freezer for a few minutes prior to processing. Do not process frozen food.

• Do not process soft or already grated cheese. Otherwise, the feed tube may become clogged.

• When using the very fine or fine grating cone D3/D7 or the grating cone for cutting slices D6, push the the food through the feed tube DB gently. When using the coarse grating cone DS it is necessary to push the ingredients through with greater force.

Quick guide to selecting a grating cone

The table provides an overview of the most frequently used food.

Ending operation and removing the grating attachment

• After you have finished using the appliance, set the control knob A11 to the O position and disconnect the power cord from the power socket.
• Touch the button A2, turn the grating attachment clockwise and pull it upwards from the multi-function head Al to remove it. After removing the grating attachment, put the front attachment hub cover A3 back in its place.
• When disassembling the grating attachment into its individual parts, proceed in the reverse sequence.
• Clean out the used accessories after each use according to the instructions in chapter CLEANING AND MAINTENANCE.

BLENDING

Warning:
Before installing or removing accessories, the multifunctional stand mixer must always be turned off and disconnected from the power socket.
When installing or removing the blender to the multi-function head A1, whilst the multifunctional stand mixer is connected to the power grid, it could happen that it is accidentally turned on and cause serious injury.

Purpose of use of the blender and adding ingredients

• The blender is intended for preparing meals and drinks such as milkshakes, creamy soups, sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and vegetables, preparing potato puree, yeast dough or for whipping egg whites.
• Cut up the ingredients into equal size pieces measuring approximately 3 cm.
• Frozen ingredients (ice cubes, frozen banana, strawberries, etc.) should not be larger than 3 cm. Ice cubes must be processed immediately upon being removed from the freezer.
• From fruit and vegetables, always remove hard peels and take out hard stones from e.g. apricots, peaches, mangos, etc., or hard seeds. Always remove the central core from pineapples. Otherwise there is a risk of damaging the blender.
• If you wish to blend coconut, always blend only its pulp.

FilUng the blending jar and assembling the blender

• Fill the blending jar E3 with ingredients.

Warning
Hot steam or splattering hot foods or liquids may cause scalding. Always pay increased attention when handling hot liquids and foodstuffs.
The glass blending jar is resistant against heat up to 55 °C. Never place food or pour any liquids with a higher temperature into it, otherwise there is a risks of the glass jar cracking, which may subsequently lead to scalding.
For reasons of increased safety, always allow hot foods and liquids to cool down before putting the appliance into operation.

Attention:
The maximum capacity of the blending jar is 1.5 litres. Never fill it past the maximum mark. When processing heated liquids or liquids that expand in volume during the blending process, do not fill the blending jar E3 to more than 2/3 of its maximum capacity.

• Place the outer lid E2 on to the blending jar E3 so that its edges copy the neck of the blending jar E3, and push it down thoroughly along its entire perimeter. Insert the inner cap E1 into the hole in the lid E2 and ensure that it is properly seated in it.

Mounting the blender on the multifunctional stand mixer (fig. L)

• Make sure that the control knob A11 is set to the O position and that the multifunctional stand mixer is disconnected from the power socket. The multi-function head A1 must be tilted down to the horizontal position and none of the attachments A15, A16, A17 or A19 may be mounted on it. The front attachment hub cover A3 must be attached in its place. The stainless steel bowlA13 may be mounted on the base AS.
• Remove the top cover AS from the multi-function head At Put the properly assembled blending jar on to the top attachment hub A7 and turn it all the way towards the closed padlock symbol.

Note:
The robot is equipped with a safety mechanism that prevents the blender from being started unless it is correctly attached to the top attachment hub A7.

Using the blender
Before connecting the multifunctional stand mixer to a power socket, always check that it is correctly assembled according to the instructions in this user’s manual, that the multi-function head
A1 is tilted down into the horizontal position and the speed control knob A11 is set to the O position. Connect the power cord to an el. power socket. Touch button B1D 00 to set the multifunctional stand mixer to stand-by mode.

Preset program
The multifunctional stand mixer has one preset program for the blending mode.
In stand-by mode, start the work cycle for the blender with the preset speed and duration by touching the button BB. The buttons
B9-B1D, the button of the selected program BS, the speed indicator B4 will be lit and time will count down on the display until the preset time has elapsed.
Note

• It is not possible to adjust the speed in a preset program while it is running. The time can be adjusted on the control panel using buttons B2 0 and B3 0.
• The maximum time that can be set in the preset blending program is 3 minutes.
• If you wish to pause a program, press button B button again will resume the program. The memory function enables the program to be started again up 10 minutes from it being paused. After 10 minutes, the display with the control panelA9 will turn off. Only button B1D (> 00 will remain active on
• the control panel.
• If you wish to end a program prematurely, press button B9 RESET] or the button BS with which you started the program.
• When the program is finished, the multifunctional stand mixer
• will beep and will stop operation, and it will switch to the stand-by mode.

Manual setting
If you do not wish to use the preset blending program, you can set the processing speed and duration yourself. You can change the speed setting while the appliance is running. We recommend
to start at a lower speed and to increase it gradually. The recommended food processing times and recommended speed settings are provided in the table Quick guide to blending.

Attention
The maximum continuous operating time in the blending mode is 3 minutes. Do not leave the appliance in the blending mode for longer than 3 minutes. Then allow the appliance to cool down for approximately 30 minutes.

Speed setting

• Turning the speed controlknobA11 to the required speed level will start the blender. The display A9 will show the elapsed time of operation. To stop the appliance, set the control knob A11 to the 0 position. This will switch the multifunctional stand mixer to the stand-by mode.
• Do not leave the multifunctional stand mixer in the blending mode for longer than 3 minutes.

Selling the speed and time of operation

Turning the speed control knob A11 to the required speed level will start the multifunctional stand mixer. The display A9 will start counting down the elapsed time of operation.
Use buttons B2 to set the desired time of operation. Do not set a time of operation greater than 3 minutes. The display A9 will show the time remaining until the set time has elapsed. When the set time has elapsed, the multifunctional stand mixer will beep, stop automatically and switch to the stand-by mode.
Set the speed control knob A11 back to the O position.

Pulse level

If you wish to increase the speed to maximum for a short time, turn the control knob A11 to position P (pulse mode) and hold it for a short time in this position. As soon as you release the control knob A11, it will automatically return to the O position. Hold the control knob A11 in the P position only for short intervals of a few seconds in duration.

Quick guide to blending

The above food processing times are only a reference. The actual mixing time depends on the size of the ingredients, their amount and the required final consistency. Advice and tips for blending

Advice and tips for blending

• Ingredients are getting stuck on the blade assembly E4 or the walls of the blending jar E3, stop the appliance by either touching button BB, which was used to start the preset program, or by setting the control knob A11 to the O position (in the manual setting). Attention: Ending the operation of the appliance will cancel all previous settings.
• Make sure that the control knob A11 is set to the O position and disconnect the multifunctional stand mixer from the power socket.
• Make sure that the blade assembly E4 has stopped rotating. Carefully remove the assembled blending jar from the multi­function head A1 by turning it towards the opened padlock symbol and then lifting it upwards. Open the lid E2 and use a plastic spatula to clean the blade assembly E4 and the walls of the blending jar E3. Make sure that there are only ingredients suitable for processing located inside the blending jar E3. Put the lid E2 back on and reattach the blender assembly to the multi-function head A1. Connect the power cord to a power socket and make the manual settings again or select the preset blending program and adjust the blending time in the appropriate manner.
• When processing heated liquids, do not remove the inner cap E1 during operation.
• When processing heated liquids or liquids that expand in volume during the blending process, do not fill the blending jar to more than 2/3 of its maximum capacity.
• Firs? blend a smaller amount of ingredients and then gradually add more ingredients through the hole in the lid while blending. In this way, you will achieve better results than by adding all ingredients into the blending jar at once.
• If you need to blend food of a solid consistency together with liquids, we recommend that you first blend the food of solid consistency and a part of the liquids. Then gradually add the remaining liquids through the hole in the lid while blending.
• To blend very thick liquids, we recommend using the pulse level so that the blade assembly does not jam. Start the blender repeatedly in short intervals.
• Ice cubes must be processed immediately upon being removed from the freezer. When the ice starts to melt, the ice cubes will stick together and it will not be possible to blend them.
• Do not process dried fruit, coffee beans, nuts, grains, etc. for longer than 1 minute.

Ending operation and disassembling the blender

• After you have finished using the appliance, set the control knob A11 to the O position and disconnect the power cord from the power socket.

• Make sure that the blade assembly E4 has stopped rotating and carefully remove the blending jar assembly from the multi-function head A1 by turning it towards the opened padlock symbol and then lifting it upwards. Properly mount the top attachment hub cover AB back in its place.

• When disassembling the blending jar into its individual parts, proceed in the reverse sequence to its assembly. Use a soft plastic spatula to remove food from the blending jar E3.

• Clean out the used accessories after each use according to the instructions in chapter CLEANING AND MAINTENANCE.
  egg white remains would harden and their removal would be more difficult. When cleaning the blending jar E3, proceed according to the procedure described below.

• Clean the blending jar E3 by filling it with 0.5 litre of clean water and 1-2 drops of kitchen detergent and then assemble the blender and run it for 10 to 15 seconds. Then turn off the multifunctional stand mixer, disconnect it from the

• power socket, and after the rotating parts have come to a stop, remove the blending jar assembly. Empty out the contents of the blending jar E3 and then thoroughly rinse out the blending jar E3 with clean water.

• If the outer surface of the glass blending jar E3 is soiled, rinse it under hot running water whilst using neutral kitchen detergent and then wash it under clean running water. Attention: When cleaning, make sure that no water enters into the underside of the blending jar E5 by which it is connected to the multifunctional stand mixer. Carefully dry any moisture or always allow it to dry out completely. Allow the internal area of the blending jar E3 to dry out completely and dry the outer surface of the glass blending jar E3 using a wiping cloth.

• Rinse the removable parts that you washed with the kitchen detergent using clean water and allow them to dry naturally or carefully wipe them dry using a fine wiping cloth.

Attention:
When cleaning the inside of the blending jar with the blade assembly E4, the grinding plates C8-C1D, grinding blade Cl, screw shaft CS and graters D3, D5-D7, pay increased attention so as not to injure yourself on the blades or sharp edges.

• Clean the outer surface of the multifunctional stand mixer using only a lightly dampened cloth. While doing this, take care that no water enters into the control knob A11.
• Only clean the front attachment hub A4 and the top attachment hub A7 using a clean wiping cloth.
• Only clean the power cord of the multifunctional stand mixer using a dry wiping cloth.

STORAGE

• Always make sure that the control knob A11 is set to the O position and that the multifunctional stand mixer is disconnected from the power socket. Clean the multifunctional stand mixer and all of its accessories that were used according to the instructions described in chapter CLEANING AND MAINTENANCE. Prior to to storage, the multifunctional stand mixer and its accessories must be clean. Likewise, make sure that the accessories are completely dry.
• Place and thoroughly mount the stainless steel bowl A13 into the base AS. Tilt the multi-function head A1 to the horizontal position. Store the multifunctional stand mixer and all of its accessories in a clean, dry place out of the reach of children and animals.

Attention:
Keep the multifunctional stand mixer away from extreme temperatures, direct sunlight and excessive humidity and do not store it in an overly dusty environment. Do not place the multifunctional stand mixer on its side. During storage, do not leave the removable accessories (blender, meat grinder, grating attachment) mounted on the multi-function head A1. Do not place anything on top of the stored multifunctional stand mixer.

TECHNICAL SPECIFICATIONS

• Rated frequency ……………………………………………………………………….. 50/60 Hz
• Rated power input.. . ………..1 ,800 W
• Weight (without accessories} ……………………………………………………….. 10.5 kg
• Total volume of the stainless steel bowl …………………………………………… 6.71
• Maximum filling capacity of the stainless steel bowl …………………….. .4.5 I
• The maximum filling capacity of the glass blending jar. ..1.51
• Maximum time of continuous operation ……………………………….. 10 minutes
• Maximum time of continuous operation of the blender ……….. 3 minutes
• Cooling time between two operation cycles ……………………….. 30 minutes
• Noise level …. . ………. 85 dB(A}

The declared noise emission level of the appliance is 85 dB(A}, which represents a level A of acoustic power with respect to a reference acoustic power of 1 pW.
Changes to text and technical parameters are reserved.

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

• This symbol on products or original documents means that used electric or electronic products must not be added to ordinary municipal waste. For proper disposal, renewal and recycling, hand over these products at determined collection points. Alternatively, in some European Union states or other European countries – you may return your products to the local retailer when  buying an equivalent new product.
  Correct disposal of this product helps save valuable natural resources and prevents potential negative effects on the environment and human health, which could result from improper waste disposal. Ask your local authorities or collection facility for more details.

• In accordance with national regulations penalties may be imposed for the incorrect disposal of this type of waste.

• For business entitles In European Union states

• If you want to dispose of electrical or electronic equipment, ask your retailer or supplier for the necessary information.

• Disposal in other countries outside the European Union.

• This symbol is valid in the European Union. II you wish to dispose of this product, request the necessary information about the correct disposal method from the local council or from your retailer.

•  This directives product related meets to it. all the basic requirements of EU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>