SENCOR 1035TQ Bagless Vacuum Cleaner Instruction Manual

SENCOR 1035TQ Bagless Vacuum Cleaner

Specifications

• Model: SVC 1035TQ 3AAA
• Type: Bagless vacuum cleaner
• Recommended Usage: Household, offices, similar areas

Product Description
The bagless vacuum cleaner is designed for use in households, offices, and similar areas. It comes with various features and accessories to facilitate efficient cleaning.

Key Features:

• Suction power control knob
• Telescopic tube for extended reach
• Combination floor nozzle for versatile cleaning
• Multiple filters for air purification
• Easy cord winding and storage

Product Usage Instructions

Safety Instructions:
It is important to follow safety guidelines while using the vacuum cleaner to prevent accidents or damage. Some key safety instructions include:

• Ensure supervision of children or inexperienced users.
• Avoid contact with rotating parts to prevent injury.
• Do not use in industrial environments.
• Avoid exposure to direct sunlight or heat sources.
• Check voltage compatibility before plugging in.
• Avoid submerging in water or rinsing under running water.

Assembly:
To assemble the vacuum cleaner:

1. Insert the hose into the air suction hole on the vacuum cleaner.
2. Press both clips on the end of the hose and insert it into the air suction hole.

Usage:
Follow these steps for efficient vacuum cleaner usage:

1. Ensure all filters are correctly installed before turning on the device.
2. Avoid blocking air outlets and suction holes during operation.
3. Use appropriate attachments for different surfaces.
4. Do not vacuum items that are prohibited as per the manual.

Frequently Asked Questions (FAQ)

• Q: Can I wash the filters of the vacuum cleaner?
  A: Yes, you can wash the filters following the manufacturer’s instructions. Make sure they are completely dry before reassembling them into the vacuum cleaner.

• Q: How often should I empty the dust container?
  A: It is recommended to empty the dust container whenever it reaches the maximum fill line to maintain optimal suction power.

Important safety instructions

• This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons, if they are properly supervised or have been informed about how to use the product in a safe manner and understand the potential dangers.

• Children must not play with the appliance. Cleaning and maintenance performed by the user must not be performed by unsupervised children.

• In the event that the power cord is damaged, have it repaired at a professional service centre to prevent causing a dangerous situation. It is forbidden to use the appliance if it has a damaged power cord.

• Pull the power plug out of the socket before cleaning the appliance or performing maintenance.
  WARNING:
  Avoid coming into contact with the rotating parts of the vacuum cleaner’s hand accessories. There is a risk of getting caught on these parts and possible injury.

• This vacuum cleaner is designed for use in households, offices and similar types of areas. Do not use in industrial surroundings.

• Do not expose the vacuum cleaner to direct sunlight and do not place it near an open fire or appliances that are a source of heat.

• Before connecting the power cord to a power socket, check that the technical details on the vacuum cleaner’s rating label match the electrical voltage in the socket.

• Make sure the power cord is not touching a hot surface or sharp objects.

• Do not submerge the vacuum cleaner under water or any other liquid and do not rinse it under running water.

• Before turning on the vacuum cleaner, make sure that all the inflow and outflow filters are installed in their place.

• When the vacuum cleaner is running, ensure that the air outlets and the suction hole are not blocked.

• Do not use the vacuum cleaner to vacuum the following items:

  • smouldering cigarettes, burning items, matches or embers;
  • water and other liquids;
  • flammable or volatile materials;
  • items, e.g. broken glass, needles, pins, etc.;
  • flour, wall plaster, cement and other building materials;
  • larger pieces of paper or plastic bags, which can easily block the suction hole.

•  Vacuuming of some types of floors or floor surfaces can create an electrostatic discharge, which presents no danger to the user.

• Do not place the suction nozzle or tube against any parts of the face.

• Always turn off the vacuum cleaner and disconnect it from the power socket when leaving it without supervision, after finishing using it and before cleaning it.

• Disconnect the power cord from the power socket by pulling on the plug, never pulling on the cord. Otherwise, this could damage the power cord or the socket. It is recommended to hold the power cord in your hand when winding it up.

• If the power cord is damaged, have it replaced at a professional service centre. It is forbidden to use the vacuum cleaner if it has a damaged power cord.

• Do not use the vacuum cleaner if it is not working correctly, if it has been damaged or has been submerged in water. Do not repair the vacuum cleaner yourself or make any adjustments to it. Have all repairs or adjustments performed at an authorised service centre. By tampering with the appliance, you risk voiding your legal rights arising from unsatisfactory performance or quality warranty.

DESCRIPTION OF THE VACUUM CLEANER

• A1 Cord winding button
• A2 On/Off button
• A3 Suction power control knob
• A4 PUSH button (serves to release the dust container)
• A5 Rubber coated wheels
• A6 Dust container lid
• A7 Dust container
• A8 Hose connection hole
• A9 Handle
• A10 Sliding flap for air suction
• A11 Telescopic tube
• A12 Telescopic tube position lock
• A13 Combination floor nozzle
• A14 Flap position for vacuuming carpets
• A15 Flap position for vacuuming hard (smooth) floors
• A16 Hose
• A17 Accessory holder
• A18 Stopper for the horizontal and
• vertical parking position
• A19 Clip
• A20 Hose end
• A21 Front travel wheel
• A22 Vertical parking position
• A23 Power cord
• A24 Inflow filter
• A25 Foam pre-filter
• A26 Horizontal parking position
• A27 Outflow filter
• A28 Outflow filter protective grille
• A29 Long flexible crevice nozzle
• A30 Crevice nozzle
• A31 Upholstery nozzle
• A32 Brush attachment (easy to attach to the upholstery nozzle for gentle vacuuming of fine upholstered surfaces)

ASSEMBLY

Inserting the hose into the air suction hole on the vacuum cleaner.
Press both the clips on the end of the hose A20 and insert it into the air suction hole A8 on the vacuum cleaner until you hear a “click”. The hose A16 is now secured in the correct position.

Attach the holder to the telescopic tube:
Make sure to place the holder with the hose on the wider part of the telescopic tube A11.

Attach the floor nozzle to the telescopic tube:
Make sure that the floor nozzle A13 is attached to the narrower part of the telescopic tube A11.

Adjust the length of the telescopic tube:
Adjust the length of the telescopic tube A11 as required – disengage and hold the clip A19 on the tube in the direction shown by the arrow and adjust the length of the tube A11 as required. Then release the clip A19 and slide out the tube A11 slightly forward until you hear a “click”. The telescopic tube A11 is now securely locked in position.

USING THE VACUUM CLEANER

• Connecting the vacuum cleaner to the power grid
• Wind out the required length of the power cord by pulling on the power plug. Insert the power plug into a power socket.

Attention:
The yellow marking on the power cord warns you that the power cord is close to its end. Do not pull the cord farther than the red marking.

Adjusting the floor inlet nozzle according to the floor surface.

You may set the inlet nozzle according to the floor surface by adjusting the inlet flap:

• If you want to vacuum carpets, move the flap to retract the bristles.
• If you want to vacuum hard and smooth surfaces, move the flap to extend the bristles.

Turning your vacuum cleaner on and off
To turn on the vacuum cleaner, press the On/Off button A2. To turn off the vacuum cleaner, press the button A2 again.

Adjusting the suction power
Suction can be controlled using the control knob A3. Turning clockwise (towards MAX) increases the power of the vacuum cleaner, and turning anticlockwise (towards MIN) reduces the power. In a smaller range, you may regulate suction power using the mechanically sliding flap A10 on the hose handle.

TIPS

• Use the maximum suction power when vacuuming carpets or floors with a hard surface. Use the reduced strength when vacuuming upholstery, window curtains, etc.
• If the hose holder becomes blocked when vacuuming, disconnect it from the telescopic tube and also disconnect the hose from the vacuum cleaner body.
  Then place the holder inside the suction hole on the vacuum cleaner’s body and vacuum the stuck dirt out.

Temporary interruption of the vacuuming process
If you wish to interrupt vacuuming for a while, you can use the horizontal A26 or vertical A22 parking position on the vacuum cleaner, into which you insert the stopper A18 on the floor nozzle.

Attention:
Do not move the vacuum cleaner from place to place if the hose is in the parked position! The stopper on the floor nozzle could break off.

Ending the vacuuming process

• When you finish vacuuming, switch the vacuum cleaner off by pressing the On/Off button A2 and then disconnect the power cord plug from the power socket.
• To wind the power cord back into the vacuum cleaner, press and hold the winding button A1 with one hand and guide the power cord with the other.

TIP:
If the winding process stops and part of the power cord is still outside, release the winding button A1 and pull the cable out again by about 50 cm and then press and hold the winding button A1 again and repeat the winding process.

USING THE ACCESSORIES

• The combination floor nozzle A13 for hard floors ensures perfect and yet gentle vacuuming of smooth hard surfaces thanks to the brush being from 100 % natural bristles. It can be used to vacuum floors that are sensitive to scratching such as wooden or floating floors, marble floors, tiles, linoleum, etc.
• The long flexible crevice nozzle A29 serves to vacuum very hard-to-reach places anywhere in your car.
• The crevice nozzle A30 is suitable for vacuuming hard-to-reach places (e.g. window frames, libraries, upholstery corners, joints, etc.).

TIP:
If during vacuuming you use an accessory very often, you may attach it to the special holder on the telescopic tube.

CLEANING AND MAINTENANCE

Attention: Before cleaning, disconnect this appliance from the power source.

Emptying the dust container

Empty the dust container A7 as soon as it fills up to the MAX mark; otherwise, the airflow and the suction power will be reduced. Nevertheless, it is recommended to always empty out the dust container when you have finished vacuuming.

1. Take out the hose A16.
2. Press the PUSH A4 button and pull out the dust container A7 upwards.
3. Remove the lid of the container A6 and take out the dust filter. Tip the dust out of it and rinse it out under lukewarm running water if necessary.
4. Take the dust container A7 above a waste bin and turn it upside down to shake the dirt and dust out of it. If it is heavily soiled you may wash the entire container under running lukewarm water. It is, however, necessary to first remove the inflow filter A24 and its foam pre-filter A25 before doing this!
5. Insert the dust filter into the dust container A7 and put on lid A6.
6. Insert the container A7 into the vacuum cleaner.

Attention:

Make sure that all parts are completely dry before reinserting the dust container A7 and the dust filter back into the vacuum cleaner.
Replacing and cleaning the inflow filter and the foam pre-filter

1. Press the PUSH A4 button and pull out the dust container A7 upwards.
2. Fold out both safety clips of the inflow filter frame A24, take it out of the dust container A7, and from behind it also remove the foam pre-filter A25.
3. Wash both filters under running lukewarm water and if necessary replace them with new ones.
4. Then first reinsert the foam pre-filter A25 and then the inflow filter A24 until you hear both clips click in.
5. Place the dust container A7 back into the vacuum cleaner.

Attention:
Never insert the filters back into the vacuum cleaner if they are wet! Always wait until they are thoroughly dry.

Replacing the outflow filter

• First remove the grill of the outflow filter A28 by pulling it away from the vacuum cleaner in the location of both safety clips.
• Then remove the outflow filter A27 and replace it with a new one.
• After reinserting the filter A27, put on the grille of the outflow filter A28 and click it in behind both clips

Attention:
Make sure you put the outflow filter A27 in the vacuum cleaner with the plastic grill facing outwards!

Cleaning the vacuum cleaner
To clean the outside parts of the appliance use a fine cloth dipped in lukewarm water. Do not use aggressive cleaning agents, paint thinners or solvents. Using these solutions could damage the surface of the appliance.

TROUBLESHOOTING

Before you decide to contact an authorized service center, please read through the following table:

power socket.

– The power socket is damaged.

– The vacuum cleaner is not switched on.

| – Insert the plug firmly into the power socket

– Inspect the power socket.

– Turn on the vacuum cleaner.

Suction power is weak| – The appliance is clogged.

– The dust filter needs cleaning.

– The dust container is not in the correct position.

– The filter is clogged.

| – Remove the blockage or foreign object.

– Clean out the dust filter.

– Close the dust container.

– Clean out the filter.

The power cord is not wound in completely.| The power cord may have slipped down from the winding pulley during winding.| Hold the cable under tension while winding the cable.
The cable cannot be pulled out.| The cable is wound up incorrectly.| Press the winding button of the self-winding cable and try to rewind the power cord again
Suction power control does not work.| The appliance is out of order.| Contact an authorized service centre.
The power cord starts to wind in when it is not required.| The winding mechanism is damaged.| Contact an authorized service centre.
The dust container cannot be closed.| The dust filter is inserted incorrectly or in an incorrect position.| Reinstall and secure the filter in position and try again.

TECHNICAL SPECIFICATIONS

• Rated voltage…………………………………………………………………………………………………….. 220 – 240 V ~
• Rated frequency……………………………………………………………………………………………………….50 / 60 Hz
• Rated power input………………………………………………………………………………………………………… 750 W
• Safety class (about electrical shock protection)…………………………………………………. II
• Noise level…………………………………………………………………………………………………………………… 75 dB(A)
• Length of power cord…………………………………………………………………………………………………………7 m
• Operating range……………………………………………………………………………………………………………… 10 m
• Dust container capacity………………………………………………………………………………………………………. 1 l
• Dimensions (length × width × height) …………………………………………….. 380 × 280 × 255 mm
• Weight…………………………………………………………………………………………………………………………… 4.75 kg

The declared noise emission level of the appliance is 75 dB(A), which represents a level A of acoustic power concerning a reference acoustic power of 1 pW. Changes to text and technical parameters are reserved.

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

• This symbol on products or original documents means that used electric or electronic products must not be added to ordinary municipal waste. For proper disposal, renewal, and recycling, hand these products over to determined collection points. Alternatively, in some European Union states or other European countries, you may return your appliances to the local retailer when buying an equivalent new appliance.
• Correct disposal of this product helps save valuable natural resources and prevents potential negative effects on the environment and human health, which could result from improper waste disposal. Ask your local authorities or collection facility for more details.
• By national regulations, penalties may be imposed for the incorrect disposal of this type of waste.

For business entities in European Union states

• If you want to dispose of electric or electronic devices, ask your retailer or supplier for the necessary information.
• Disposal in other countries outside the European Union.
• This symbol is valid in the European Union. If you wish to dispose of this product, request the necessary information about the correct disposal method from the local council or your retailer.

This product meets all the basic requirements of EU directives related to it.
Copyright © 2023, Fast ČR, a.s.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>