Orbegozo SP 6200 2000W Horizontal Heater Instruction Manual

Orbegozo SP 6200 2000W Horizontal Heater

IMPORTANT SAFEGUARDS

1.  This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must never play with the appliance. Cleaning and user maintenance must never be carried out by children without supervision.
2. Children should be supervised to ensure that they do not play with the appliance.
3. please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.
4.  If the supply cord is damaged it must be repaired by the Authorized Service Agent.
5.  Never pull on the cord when unplugging.
6.  Do not use the unit with a damaged cord or plug, or if it is not working properly.
7.  Do not handle the appliance with wet hands.
8.  Never immerse the appliance in water or any other liquid.
9.  Make sure the appliance has been unplugged before cleaning.
10.  This appliance must be installed following the national regulations for electrical installations.
11. 11. This appliance is for household use only.
12.  In case that you need a copy of the instruction manual, you can find it in www.orbegozo.com.
13.   WARNING : In case of misuse, there is a risk of possible injury.

• WARNING : In order to avoid overheating, do not cover the heater
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION : Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• The device should not be placed immediately below a socket base.
• Do not place a heater in use near curtains, furniture, wood paneling or combustible material which can deteriorate with heat.
• control room. Do not use this heater in small rooms that are occupied by people who cannot leave the room by themselves, unless you provide surveillance.
• The appliance must be installed so that the switches, thermostat and power cable cannot be touched directly or indirectly by a person in the bath or shower.
• The heating appliance must be installed at least 1.8 m above the ground.
• The air outlet must be hanged downward on the wall and horizontal. Do not install the appliance differently or diagonally.
• Do not use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• Keep the appliance at least 1 meter away from flammable materials, such as furniture, curtains, bed clothing, clothes or paper.
• Do not use the heater in areas where petrol, paint or other flammable substances are used or stored.

TECHNICAL DATA

INSTALLATION ON THE WALL

Drill two holes in wall and have a distance of 1.8m from the ground. The diameter of the hole just contained the inflated plastic pipe (8 mm). Introduce inflated plastic pipe into the holes and screw supplied screws letting them stick out a little. Hang the appliance on the screws.

FUNCTION OPERATION (CONTROL PANEL AND REMOTE CONTROL)

CONTROL PANEL

REMOTE CONTROL

Control panel operation

1. Plug in and switch on by pressing the main switch 0/I, enter into standby mode and display shows S.

2.  Once press F, enter into fan mode, display shows like photo A; press F in second time, enter into lowerheating, display like photo B; press F in third time, enter into high heating, display like photo C, press in fourth time, enter into in standby mode (fan keeps working for 30 seconds before shutting down completely).

3.  Turn-off timer. Press button to set timer (1-12hours) during working status. Pressing the button one time increases one hour for timer. After setting time, the display will show current setting time for 5
   seconds, then resume to previous display, meanwhile the light on. Below photo is an example of setting 8h.

4. Turn-on timer. In standby mode, press timer button, you can set the appointment turn-on time in 1-12 hours. After complete setting, the display shows the appointment turn-on time and also the light is on. The display automatically decreases 1 hour for each hour passed. When the appointment power-on time arrived, the product will automatically turns on. The default setting temperature is 23 during appointment turn-on. Below photos is an example to set appointment turn-on time to 8 hours:
   Note : if you don t set the temperature or weekly program, the heater will turn off automatically after continuous use of 12 hours and enter into standby.

5. Temperature setting. While – (temperature range 10-49ºC). For example: the current temperature of the room is 15ºC, when you set the heater temperature to 25ºC, display will light on as below picture. If you want to cancel selected

Remote control operation

Note : during operation, ensure remote control aims to receptor on appliance to working correctly.

1.  Press to turn on the heater, fan function will active and display will light as pic. A.

2. Press once, heater will work in min. Power heating and display will show (pic. B). Press again, max. C Power heating and display will show / (pic. C).

3.  Timer function works the same as timer button on control panel.

4.  Set current time/day (it can be set under standby mode & working status): press button once, display shows the hour, press / to set current hour (total 24 hours) ; pressshow minutes, press / to set current minutes (00-59 minutes); press for third time, display will / to set current day (Monday-Sunday: d1-d7). Then press to confirm the configuration, display will show previous setting. For example: setting to Wednesday, 9:30 AM, 25ºC, max. power of heating, display will be:

5.  Set temperature. During working status, press to set desired temperature (temperature range 10-49ºC), press to confirm the setting or wait a few seconds. For example the current room temperature is 15 , when set temperature to 25ºC, the display shows as following pic. If want to cancel the set temperature, press to set the low or high heating instead of set temperature. ºC light turn off.
   Note : when setting temperature, it will use smart working way as follows:

6.  If room temperature is 2ºc or lower than set temperature, the heater will work in max power heating.

7.  If room temperature is less than 2ºc of set temperature without reach it, heater will work in min power heating.

8.  If room temperature is the same as set temperature, heater will work in fan mode for 30 seconds to cool down the appliance and protect its components, after that it will enter in standby mode.

9.  After this situation if room temperature is lower than 2ºc of set temperature, heater will turn on again and work as same way.

10. Set weekly program (only by remote control)

11.  Press , the product enter into working status.

12.  After set current hour/day as point 4 explains, follow next instructions to set weekly program.

13.  Press , weekly program setting.(pic. A)

14.  Press , the display shows d1~d7, set to working days as required (Monday-Sunday: d1~d7). Such as set Monday, the display as (pic. B)
    Note : in order to distinguish between setting current day & working period of the day: current day – Monday-Sunday: d1~d7; working period – each day: p1~p6.

15. Press , the display shows p1~p6 (for each day, it can be set maximum 6 time periods).for example, 1st period setting.(figure c).

16.  Press , continuously to set the turn-on time. Such as set the turn-on time 7:00am (as figure d ) (memo: the setting time 0-24 for choice).

17.  Press , the display shows the previous setting turn-on time by default. Press continuously to set the turn-off time. Such as set the shutdown time at 13:00pm (the display as figure e), (note: turn-off time later than turn-on time, when turn-on time same as turn-off time, the unit in standby mode).

18.  Repeat steps 4-7 above, you can set the whole weekly program (& each day, the work of each segment opens, the time of shutdown).

19. Set open-window detection(only by remote control)

20.  Press , the product enter into working status. Heating for a moment to stable.

21.  Press by remote control, light /ºC light on; the temperature display 23 by default. Press /to set target temperature. During open-window detection mode, once the room temperature drops 5-10ºC within 10 minutes, then the product will stop working within 30 minutes and enter into standby mode. Turn on the unit, it need press again.

22.  Open-window detection and weekly program can work simultaneously (pic. G). Heater will work according the program and set temperature and if room temperature decrease 5-10ºC for 10 minutes the appliance will stop and enter in standby mode.

CLEANING AND MAINTENANCE

Unplug from the outlet before cleaning. Allow to cool before cleaning the appliance. To clean the surface use the soft wet cloth (or cloth with some scour). Make sure that do not pour water on to the appliance. Do not use any organic solvents such as gasoline or toluene. If you do not use the appliance for a long time, wipe off the surface and store the appliance in the original packing box at a well-ventilated place. Avoid dampness and impacts.

heaters**

only (select one)

Nominal heat output| P| 2.0| KW| | manual heat charge control, with integrated thermostat| [ no ]
Minimum heat

output (indicative)

| P| 1,0| KW| | manual heat charge control with room and/or outdoor temperature feedback|   [ no ]
Maximum

continuous heat output

| P     ,| 2,0| KW| | electronic heat charge control with room and/or outdoor temperature feedback|   [ no ]
Auxiliary electricity consumption| | fan assisted heat output| [ no ]
At nominal heat

output

| el| 0| KW| | Type of heat output/room temperature control (select one)
At minimum heat output| el| 0| KW| | single stage heat output and no room temperature control| [ no ]
In standby mode| el| 0.000| W| | Two or more manual stages, no room temperature control| [ no ]
| | with mechanic thermostat room temperature control| [ no ]
| | with electronic room temperature control| [ no ]
| | electronic room temperature control plus day timer| [ no ]
| | electronic room temperature control plus week timer| [ yes ]
| | Other control options (multiple selections possible)
| | room temperature control, with presence detection| [ no ]
| | room temperature control, with open window detection| [ yes ]
| | with distance control option| [ no ]
| | with adaptive start control| [ no ]
| | with working time limitation| [ yes ]
| | with black bulb sensor| [ no ]
Contact details info| SONIFER SA. Avenida de Santiago 86, 30007, Murcia. Spain.

Disposal of old electrical appliances

The European directive 2012/19/UE on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment dispose of the appliance, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. DECLARATION OF CONFORMITY: This device complies with the requirements of the Low Voltage Directive 2014/35/EU and the requirements of the EMC directive 2014/30/EU.

References

• Orbegozo Electrodomésticos | Todo para tu hogar y cocina

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>