EK Water Blocks AM5 EK-Quantum Magnitude UNC Standoffs User Manual

EK Water Blocks AM5 EK-Quantum Magnitude UNC Standoffs

Product Information

The EK-Quantum Magnitude Upgrade Kit – AM5 is a product designed for liquid cooling systems. It includes a water block that is compatible with AM5 motherboards. The kit comes with all the necessary components for installation, including mounting standoffs, screws, springs, and a D-RGB LED strip.
Before using this product, it is important to follow some basic guidelines:

• Read the manual carefully before starting the installation process.
• Use corrosion inhibiting coolants for liquid cooling systems, especially for nickel-plated water blocks.
• Avoid using pure distilled water and instead use EK-Cryo Fuel coolants for optimal results.
• Bleed air out of the water block thoroughly to achieve optimal performance.

Product Usage Instructions

Preparing the AM4 Water Block for Upgrade

Important! Before starting, make sure to have a clean, flat surface to work on. It is recommended to put foam or soft material to lay a motherboard on.

1. If the EK-Quantum Magnitude AM4 water block is already installed, unscrew the four mounting screws using Allen Key 2.5 mm and detach it. Save the parts for later use.
2. Clean the CPU cold plate using a non-abrasive cloth or Q-tip.

Preparing the AM5 Motherboard

1. Using a Philips-head screwdriver, remove the four UNC 6-32 screws securing the original plastic hold-down clamps around the socket. Remove the hold-down clamps and store them away.
2. Clean the CPU integrated heat spreader (IHS) using a non-abrasive cloth or Q-tip.
3. Applying thermal compound: Apply the enclosed thermal grease (thermal compound) on the CPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even in thickness over the entire surface of the IHS.
   The excessive or uneven application of thermal grease may lead to poor performance!

Installing the Water Block

1. Loosely install all four (4) provided AM5 Mounting Standoffs before proceeding to tighten them completely. Using pliers or similar tools is not recommended.

2. Position the AM4 CPU Water Block onto the AM5 Mounting standoffs. Make sure to align the holes (as shown in the picture).
   Make sure to double-check the layer of the Thermal Grease before placing the water block onto the motherboard.

3. Insert all four saved Springs inside the frame.

4. Loosely insert all four saved Screws before proceeding to tighten them using Allen Key 2.5 mm. Tighten the screws two revolutions at once in a cross pattern until they are flush with their holes inside the frame.

Connecting the D-RGB LED Strip

1. Plug the 3-pin connector from the water block’s D-RGB LED light to the DRGB HEADER on the motherboard. Ensure that the pin layout on the header is as follows: +5V, Digital, empty, Ground.

Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. If you put the LED Diode to the 12V RGB HEADER you can damage the LEDs. Failure to do so will damage your motherboard or LED strip.

For more information, warranty details, and support, refer to the user manual provided with the product.

BOX CONTENTS

TESTING THE LOOP

To make sure the installation of EK components was successful, we recommend you perform a leak test for 24 hours. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. Turn on the PSU and let the pump run continuously. It is normal for the coolant level to drop during this process as air collects in the distribution plate. Inspect all parts of the loop, and in the eventuality that coolant leaks, fix the issue and repeat the testing process. Ensure that all hardware is dry before the system is powered on in order to prevent any damage.

WARRANTY

Our products are warranted against defects of materials and quality for a period of 24 months, starting with the date of delivery to the end-user. During this period, products will be repaired or have parts replaced at our discretion, provided that 1) the product is returned to the agent from whom it was purchased; 2) the product has been purchased by the end-user and has not been used for commercial purposes; 3) the product has not been misused, handled carelessly, or used in a manner other than the way described in the instructions manual. This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids. EK water blocks are sealed with a warranty-voiding circular label, proving the water block has withstood a pressure leak test. Removing the label will void the leak-free guarantee, but not the guarantee on the product itself. Any other RMA issues can be reported to EK Customer Support at www.ekwb.com/support for further analysis.

SUPPORT AND SERVICE

In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia – EU

References

• EK Connect - Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>