Connects2Vision CAM-FT6 Wide-Angle Brake Light Camera User Manual
- June 10, 2024
- Connects2Vision
Table of Contents
Connects2Vision CAM-FT6 Wide-Angle Brake Light Camera
User Manual
PRODUCT INFORMATION:
The CAM-FT6 is a wide-angle brake light camera, suitable for the Fiat Ducato.
This camera utilises several camera views to assist the driver in manoeuvres
including:
Birds eye, wide angle, reversing, blind spots and standard driving mode.
Vehicle compatibility:
Fiat Ducato (X250) 2006 – 2014
Fiat Ducato (X290) 2014 – 2021
PRODUCT FEATURES:
Image Sensor: 1/4”
TV Lines: 480
Resolution: 720 x 480
Minimum Illumination: 0.1 Lux
TV System: NTSC
Waterproof Rating: IP67
Viewing Angle: 210 Degrees (Horizontal) 140 Degrees (Vertical)
Parking Lines: Yes (Removable)
Image Adjustment: Yes (up to 5 different viewing modes)
Enhanced Performance In Low Light: Yes
Operating Voltage: 12-24V DC (Negative Ground)
Operating Temperature: -20 Degrees C to +75 Degrees C
DISCLAIMER:
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for
installation. The place of installation must be free of moisture and away from
heat sources. Please ensure you use the correct tools to avoid damage to the
vehicle or product.
Connects2 can not be held responsible for the installation of this product.
Technical Support
Connects2 want to provide a fast and suitable resolution should you encounter
any technical issues. With this in mind, when contacting Connects2, try to
provide as much Information as possible. This will speed up the process and
help us to help you.
Please use our dedicated online technical support centre:
support.connects2.com
INSTALLATION
Wiring Diagram
| Red | Acc 12V | Connect to vehicle 12V Accessory feed |
|---|---|---|
| Black | Ground | Connect to source of ground |
| Brown/White | N/A | N/A (wire not needed) |
| Red (Twisted) | CAN + | Connect to rear of OBD (see diagram on Page 3) |
| White (Twisted) | CAN – | Connect to rear of OBD (see diagram on Page 3) |
| Brown RCA | Video In | Connect to head unit’s video input connection |
Vehicle Connection Overview
Connecting CAN-Bus Wiring
Locate the vehicle’s OBD port and unscrew/remove the female connector.
On the reverse of the connector (the side where wiring enters it), connect the
CAN + (red) and CAN – (white) wires from the harness to the locations
specified in the diagram (Pins 1 and 9).
USING THE WIRELESS CONTROLLER
Start-Up
The wireless controller included in the kit can be used to change the viewing
mode of the camera, as well as adjust key parameters for each viewing mode.
To bring up the HUD menu, put the vehicle into reverse gear and press A.
Note: The HUD menu will time-out after 3 seconds to allow an uninhibited view
of the camera image.
Press the A button to bring the HUD menu back onto the
screen.
The currently selected viewing mode is displayed by the icon in the centre of
the HUD menu. This will default to Driving/Rear-View mode, or to Reversing
mode when in reverse gear.
To change the camera mode, whilst the vehicle is in reverse gear, press B or C
to cycle through the Reversing, Wide Angle and Birds-Eye viewing modes.
Viewing Modes
Adjusting Settings
To adjust settings for all viewing modes, press A from the HUD menu to enter
the settings menu.
Once in the settings menu, short press A to cycle through the various settings
screens available. Screens include camera angle and position for each mode,
and guideline width for parking lines.
Once in a settings screen, the selected setting is indicated by the icon in
the centre of the display. The parameters can be adjusted with B and C.
To return to the previous screen, Press and hold A.
Activating/Deactivating Blind Spot View (BSV) Mode
When in any of the settings screens, a long press of B will activate or
deactivate BSV (Blind Spot View).
When active, this will trigger the blind spot camera image when an indicator
is activated and the vehicle is moving at a speed of over 40km/h.
When inactive, using the indicators will not trigger the blind spot view and
the camera will remain in Driving/Rear-View mode.
Note: this function will only work if the CAN-Bus wiring is connected.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>