Telran 980452 Optical Cable Measuring Tester User Manual

May 15, 2024
TELRAN

Telran 980452 Optical Cable Measuring Tester

Telran-980452-Optical-Cable-Measuring-Tester-FIG-
\(2\)

Specifications

  • Transmitter specifications:
    • Tone frequency: 200kHz
    • The Max length distance: 2000 feet
    • The Max depth distance: 3 feet
    • The Max. working current: Less than 70mA
    • Tone mode: 1 Tone
    • Max. signal voltage: 15Vp-p
    • Signal display: Signal tone, Antenna
    • Voltage protection: DC48V
    • Battery type: 3.7V Lithium battery
    • Dimensions (LxWxD): 49 x 135 x 33 mm
  • Receiver specifications:
    • Frequency: 200kHz
    • The Max. working current: Less than 70mA
    • Earphone jack: 1pcs
    • Battery type: 3.7V Lithium battery
    • Dimensions (LxWxD): 43 x 168 x 27mm

Product Usage Instructions

How to Use:

  1. Prepare the transmitter by supplying power and connecting the wire to be traced.
  2. Switch on the transmitter and adjust settings as needed.
  3. Use the receiver to scan the area for the signal emitted by the transmitter.
  4. Once the signal is detected, follow the audio cues to locate and trace the buried wire.
  5. Mark the ground where the wire path is determined for future reference.

Note:

  • For different types of wires, follow specific instructions provided in the manual.

How to Properly Install the Battery:
Organize the battery line and place it in front of the battery without putting it on top.

How to Enhance the Signal:
To enhance the signal, use a ground stud by connecting it properly using suitable tools.

How to Find Wire Locates:
Turn on the receiver and listen for audio cues. Move the receiver back and forth to detect wire location based on signal strength.

FAQ

  • Q: How deep can the device detect wires?
    A: The device can detect wires up to a depth of 3 feet.

  • Q: What is the maximum length of wire that can be traced?
    A: The device can trace wires up to a maximum length of 1640 feet.

  • Q: How should I handle shielded wires with the device?
    A: For shielded wires, follow specific instructions in the manual to test line direction and handle signal interference.

Underground Wire Locator

  1. Helpful-loca ting & tracking buried and hidden wires
  2. Easily locate pet fence wires, metals pipes, electrical wires, etc.
  3. Wire tracer range-up to 2 feet deep and 1000 feet in length.
  4. Power: Rechargeable Lithium battery.

Transmitter specifications

Tone frequency 200kHz
The Max length distance 2000 feet
The Max depth distance 3 feet
The Max. working current Less than 70mA
Tone mode 1 Tone
Max. signal voltage 15Vp-p
Signal display Signa l tone, Antenna
Voltage protection DC48V
Battery type 3.7V Lithium battery
Dimensions (LxWxD) 49 x 13 5 x 3 3 mm

Receiver specifications

Frequency 200k H
The Max. working current Less than 70mA
Earphone jack 1pcs
Battery type 3.7V Lithium battery
Dimensions (LxWxD) 43 x 168 x 27mm

Product Introduction

Underground wire tracer can help locate & track buried and hidden wires, quickly and accurately locate the break-point and direction of underground and wall-through cables. Detect and repair broken cables by yourself, time and money saver.
It can be used to bury sprinkler valves, wire trackers, dog fence wire break locators, ducts, invisible fence wire break locators, walls buried wire tracers, electrical wire tracers, network cable testers, electric fence tester, etc.
Do not use on live circuits to avoid damaging the Tester! The underground wire tracer is only to locate a non-energized Cable. for single-core or double-core wire, NOT FOR multi-core wire and bundled wires and stranded wire.

Function comparison

Description 980452
Power supply for transmitter 3.7V Lithium Battery
Power supply for Receiver 3.7V Lithium Battery
Trace underground cable pipe
Depth range 0.8m (2.6 feet)
Max cable length 500m (1640 feet)
Working environment NO/Low voltage

Instruction for Keys and Ports

Telran-980452-Optical-Cable-Measuring-
Tester-FIG- \(3\) Telran-980452-Optical-Cable-Measuring-Tester-FIG-
8

Main features

  1. Detecting & tracking break-points of underground and wall-through wires.
  2. Suitable for 2.6 feet in depth and 1640 feet in length.
  3. Applicable to pet fences, irrigation cables, and construction sites.
  4. LED light and earphones.

How to use

  1. Push the transmitter switch to “Cable Scan” and turn the dial switch to High Tone.
  2. Connect one of the transmitter’s alligator clips to the cable, and connect the other one to an independent ground using a grounding stake or screwdriver, or to an independent ground using a grounding conductor of an unshielded lead-in wire.
  3. Swing the receiver antenna close to the ground and about 10-15 feet away from the transmitter position. (You will hear tones on either side of the path, with a null directly over the path).
  4. Proceed along the path in the zero direction and adjust the transmitter and receiver for longer distances.
  5. Once the path is determined, mark the ground at the zero point on the path.
  6. Angle the receiver antenna 45 degrees from the ground and move away from the wire path at a right angle until another null point is found. Mark this point. (Fig.01).
  7. The distance between the two marks is the approximate depth of the wire.

Note

  1. For single-core or double-core wire:
  2. Red alligator clips is the signal line, and Black alligator clips is used to connect the ground or neutral line unloaded.
  3. For shielded wire and multi-stranded wire:
  4. A: Unable to determine break-point due to signal interference, but line direction can be tested.
  5. B: If it is the direction of the shielded wire detection line, the red clip should grip the shielding layer.

How to properly install the battery?
You need to organize the battery line and put them on the front of the battery, PLEASE DO NOT put the battery line on top.

How to Enhance the Signal?
To enhance the signal you can make the ground stud and connect it. (Screw knives or metal slices can be used as a medium for ground studs).

How to find the wire?

  • Turn on the receiver and swing it back and forth. You will hear the sound “bi bi bi”;
  • When approaching the breakpoint, the tone will weaken and then disappear.
  • If the tone disappears. It means the breakpoint is at this location.

External Earphones
Equipped a pair of Earphones that can be connected to the receiver Earphone jack to improve efficiency in a noisy environment. (Fig.02)

White LED Flash-Light
The user can activate the LED flashlight by pressing the ‘Push For Light’ button. (Fig.03)

Product Parameters

Telran-980452-Optical-Cable-Measuring-Tester-FIG-
7

Packing list

Telran-980452-Optical-Cable-Measuring-Tester-FIG-
6

19 Hayezira St. Industrial Zone Ramla 7255616
www.telran.co.il
office@telran.co.il
fax. 03-5214524
Technical support $2023
phone : 03-5575110

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals