Shenzhen Zhenling Technology MT7601U Mini Camera Alarm Clock User Manual
- June 9, 2024
- Shenzhen Zhenling Technology
Table of Contents
Shenzhen Zhenling Technology MT7601U Mini Camera Alarm Clock
mini Camera Alarm Clock Operation Manual
The device is surveillance equipment only applicable to legal purposes. If the device is used for illegal purposes, all legal liabilities and consequences thereof shall be irrelevant to our company.
- APP download and installation; IOS/ANDRIOID (search the APP name “LOOKCAMPro”)
- Scan the QR code to download and install the APP (Figure 2)
(All the authorities prompted upon APP download shall be enabled)
Camera indicator status;
Yellow find icates that the device is charging (off when fully charged) Red indicates WiFi/AP peer to peer mode (slow blinking means the host is providing a hotspot/account) Blue indicates connection to the internet (fast blinking indicates linkage in progress, perm anent lighting indicates linkage completion) (If you don’t know the exact status, simply reset the camera to switch it to the peer to peer mode) Precautions: the resetting must be done when the red light is fast blinking or slow blinking, otherwise it wi ll not be functioning. Press and hold the reset key for 5 sec or so, to light off all the camera’s indicators. Then the camera will restart in merely 30 sec.
APP operation.
Peer to peer connection of the mobile phone to the camera
Enter the WI FI signal option of the mobile settings, find the camera’s signal
(the signal refers to the camera’s UID/model, unique to each camera) and
connect it. It is as shown in the picture
Open the mobile APP (LOOKCAMPro), enter the camera, as sho wn in the following
picture.
Remotely set the camera as follows
(select the
WiFi network to be connected, enter the password (it must be correct) and
complete, then wait till the camera completes its restart, which takes about
40 sec. The ca mera will become online from the offline status, at that point
the indicator will be permanently on in blue light. Upon successful
connection, online video can be viewed remotely. (default password is 6666)
Specification and parameters
|
---|---
Resolution Ratio| 4K/2K/1080P/720P
Video Format| MP4
Frame Number| 25
Visual Angle| 90/150 degree
Motion Detection Camera
Shooting
| Straight line 6 –10meters
Minimal Illumination| 1LUX
Video Duration| Over 1 Hours
Compressed Format| H.264
Recording Range| 5㎡
Consumption| 380MA/3.7V
Storage Temperature| -20-80 degree centigrade
Operating Temperature| -10-60 degree centigrade
Operation Humidity| 15-85%RH
Memory Card Type| TF card
Player Software| VLCPlayer/SMPlayer
Mobile Phone Operating
System
| Android/iOS
Q&A
- Remote surveillance is lagging. Please select the appropriate video resolution according to the actual network environment.
- SD card storage failure or failure in memory card reading. Before using the SD card for the first time, the SD card must be formatted.
- Failure of network connection. After resetting, please first connect the wifi signal of the camera before further configuration. The camera network supports 2.4G WiFi but not 5.8G WiFi, so please select the correct connection method.
- APP remote view of SD card videos is lagging. The decoding capacity of different mobiles is varied. Please adjust the camera’s recording to the resolution appropriate to your mobile phone.
- I forget the password. Please press and hold the reset key of the camera for 5 sec to restore the factory setting.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protect on against harmful interference in a re sidential installation. This equipment generates, uses an d can radiate radio frequency energy and, if not installed and used in accordance with the instru ctions, may cause harmful interference to radio communications. However, there is no guarantee tha t interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is e ncouraged to try to correct the interf erence by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receive r is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two co nditions: ( This device may not cause harmful interference, and ( this device must accept an y interference received, including interference that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance co uld void the user's authority to operate the equipment.
FCC Radiation Exposure Statement This equipment must be installed and operated
in accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20
c m from all persons and must not be co located or operating in conjunction
with any other ant enna or transmitter. End users and installers must be
provide with antenna installation instruction ns and transmitter operating
conditions for satisfying RF exposure com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>