FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual

June 5, 2024
FLYWOO

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction
Manual

1/ drone introduction

FLYWOO Firefly baby quad ANALOG V1.0

Review: Flywoo Baby Quad ­ Tiny Whoop Sized Drone Carrying GoPro
In an effort to push the boundaries of carry the camera on the smallest platform, Fly woo designed the smallest quadcopter possible in their history. Firefly Baby Quad , a nanosized fpv drone designed to carry Instar 360go SMO 4K camera for some action flying. Weighing in at just 47g , the Firefly Baby Quad is small , flexible, stable , but is full of power and offers unmatched control . Pilots can quietly enjoy the fun of shooting a video without jelly. The Baby Quad is equipped with GOKU F411 13A STACK and 4pcs ROBO 1202.5 5500KV motors, to bring the Firefly a quiet, stable, flexible and long flight time characteristics. Perfect for the indoor and outdoor recording every beautiful flying moment!

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
drone introduction

Battery recommend
Flight time: About 4:30min flight with Explorer 450mAh 4S battery About :3:30 min flight with Explorer 300mAh 4S battery

2/ Configuration and wiring diagram description

Specifications
Item: Firefly Baby Quad Analog Micro Drone
Weight: 47g (without battery)
Wheelbase: 80mm
FC & ESC : GOKU F411 16*16 STACK – ( FC+13A ESC )
Frame: Firefly Baby Quad Frame (Analog Version)
FLYWOO Firefly baby quad ANALOG V1.0
Motors: Robo 1202.5 5500KV
Props: HQ 40mm 4-Blades
Props Receiver Option: Frsky XM+ / TBS Crossfire
VTX: Goku VTX625 450mw
Antenna: Atomic 5.8GHz Antenna Length 30mm (RHCP)
Battery: 4S 450mAh / 4S 300mAh battery (Not including

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Configuration and wiring diagram description

Super non-slip upgrade
High Quality sticky battery pad for your LiPo Batteries. This durable battery pads made from PU material can stick to a battery at 90° on its side and even rotate 180° without falling! Fly Woo’s newest strap offering is a perfect balance of light weight, functionality and durability. The surface of the Strap is covered with non-slip silicone . Perfect for micro drones

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Super non-slip upgrade

PID and filter settings

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual - PID
and filter settings FLYWOO 1505750 Firefly
Baby Quad Analog Micro Drone Instruction Manual - PID and filter
settings

Frequency table:

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Frequency table FLYWOO 1505750 Firefly Baby Quad
Analog Micro Drone Instruction Manual - Frequency table

https://flywoo.net/pages/manual

3/ Receiver binding

TBS NANO 915: When the USB is connected, the green light of the receiver flashes, and then bind according to the picture operation. https://www.youtube.com/watch?v=-iNkVcOLITM&ab_channel=Danimal3D

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Receiver binding

ELRS 2.4G RX:

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
ELRS 2.4G RX

Bind procedure:
– Supply power to the EL24E/EL24P rx, wait until the LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the LED light will start to double- flash, which means that the RX enters the binding mode
– Insert the 2.4G ELRS TX to Radio transmitter, and choose External RF mode to CRSF protocol, then you can find ELRS menu from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press [Bind], the LED on the RX module will getting to be solid if bind successfully.
– Receiver LED status meanings: EL24E/EL24P RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade firmware of the RX via visit 10.0.0.1 from the web browser(password: expressers)

R9MM FCC ACCESS OTA:
Make sure your remote control supports ACCESS protocol, then follow the link to register and bind https://www.youtube.com/watch?v=az5hDdNBcjg&t=9s&ab_channel=FrSkyRC
If the remote control is ACCST protocol, please bind as follows: 1/ Put these two files into the firmware directory of the SD card of the remote control. R9MM firmware: FW-R9MM-ACCST_v20190201 R9M TX module: FW-R9M-ACCST-20190117

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
R9MM FCC ACCESS OTA FLYWOO 1505750 Firefly Baby
Quad Analog Micro Drone Instruction Manual - R9MM FCC ACCESS
OTA
FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual - RX
is powered on again

XM+ receiver:
1/ Press the XM+ receiver button, USB power supply, the red and green lights are always on
2/ The remote control turns on the binding mode, the green light flashes to indicate successful binding, turn off and restart

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual - XM+
receiver
3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver.

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Then set the corresponding serial port and receiver

4/ Mode setting:

Set the ARM switch and flight mode switch, AUX* corresponds to the remote control switch, and the yellow area mark is turned on.

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Mode setting

5/ Motor test:

Unload the propeller, test the rotation direction of the motor, turn on the safety switch, and test the rotation of the motors one by one.

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Motor test

6/ Flight firmware upgrade and write default CLI

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Flight firmware upgrade and write default CLI FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Flight firmware upgrade and write default CLI

https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
3/ Then load the local HEX firmware and wait for the flashing to complete. A green progress bar is displayed to indicate completion, and DFU will become a COM port

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Then load the local HEX firmware and wait for the flashing to
complete4/ After the connection is entered, it is a blank interface, you need to write CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
After the connection is entered

5/ If the command is not restarted after writing the command, please write SAVE and press Enter to save, and the FC will restart

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual - If
the command is not restarted after writing the command

6/ Then all functions of FC return to normal.

FLYWOO 1505750 Firefly Baby Quad Analog Micro Drone Instruction Manual -
Then all functions of FC return to normal

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals