VISUAL COMFORT and CO 700FIA24 Fiama Suspension Ceiling Lights Instruction Manual

VISUAL COMFORT and CO 700FIA24 Fiama Suspension Ceiling Lights

Specifications :

• Product: Fiama Suspension
• Model Numbers: 920FIA, 700FIA24, 700FIA30, SLCH14930, 700FIA48 1.01
• Intended Use: Suitable for damp locations
• Dimming Compatibility: ELV, TRIAC, or 0-10V dimmers

Product Usage Instructions

Install the Fixture:

1. Separate the mounting plate from the canopy by unscrewing/removing the cap nut from the threaded nipple.
2. Secure the mounting plate to the electrical box with the two #8-32 screws provided.
3. Place the fixture on a level surface.
4. Loosen (do not remove) the set screws on the strain reliefs using the provided Allen wrench.
5. Pull the coaxial cables up through the strain reliefs evenly to raise the fixture to the desired height. Take caution not to remove the inner bushing from inside the strain relief while pulling the coaxial cord through.
6. Ensure the canopy is level and re-tighten the set screws on the strain reliefs.

Shortening the Coaxial Cords:
If shortening of the coaxial cords is necessary:

• Take note of the wire connections from the coaxial cables to the driver(s) and remove the wire nuts.

Note: Refer to the minimum overall length chart on the next page for specific lengths based on model.

FAQ:

• Q: Is this product suitable for outdoor use?
  A: This product is suitable for damp locations but not intended for outdoor use.

• Q: Can I use any type of dimmer with this product?
  A: This product can be dimmed with most ELV, TRIAC, or 0-10V dimmers for optimal performance.

Fiama Suspension
700FIA24, 700FIA30, SLCH14930, 700FIA48

MODERN COLLECTION

GENERAL PRODUCT INFORMATION

• These fixtures are intended to be installed utilizing NEC compliant junction boxes.
  This product is suitable for damp locations.

• This product can be dimmed with most ELV, TRIAC, or 0-10 V dimmers. This instruction shows a typical installation.

CAUTION – RISK OF FIRE
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°C supply conductors.
SAVE THESE INSTRUCTIONS!

Install the Fixture

1. Separate the mounting plate from the canopy by unscrewing/removing th cap nut from the threaded nipple.

2. Secure the mounting plate to the electrical box with the two #8-32 screws provided.

3. Place the fixture on a level surface.

4. With the provided Allen wrench, loosen (do not remove) the set screws on the strain reliefs.

5. Evenly pull the coaxial cables up through the strain reliefs to raise the fixture to the desired height.
   NOTE : Take caution to not remove the inner bushing from inside the strain relief while pulling the coaxial cord through.

6. Ensure that the canopy is level and re-tighten the set screws on the strain reliefs.

7. SHORTENING THE COAXIAL CORDS See next page for minimum overall length chart():

   • If shortening of the coaxial cords is necessary, take note of the wire connections from the coaxial cables to the driver(s) and remove the wire nuts.
   • Leave 6″ behind for wire connections, cut off the excess cord.
   • From the end of the cord, strip the insulation 4″ using a sharp knife. Make sure not to nick the inner wires.
   • Strip the ends of the wires and reconnect the wires to their original connections using the wire nuts.

8. Connect the fixture to a suitable ground in accordance with local electrical codes.

9. Connect the white driver wire(s) to the neutral power line wire with a wire nut.

10. Connect the black driver wire(s) to the hot power line wire with a wire nut.

11. Place the canopy onto the threaded nipple and secure it in place by screwing the cap nut onto the threaded nipple.

MINIMUM OVERALL LENGTH (OAL.) CHART

FIAMA 24| FIAMA 30| FIAMA 36| FIAMA 48
Min/Max OAL. Approx. 14”/ 147”| Min/Max OAL. Approx. 17”/ 148”| Min/Max OAL. Approx. 20”/ 148”| Min/Max OAL. Approx. 26”/ 148”
With Choker Ring 9”from Ring to fixture MINIMUM.| With Choker Ring 12”from Ring to fixture MINIMUM.| With Choker Ring 15”from Ring to fixture MINIMUM.| With Choker Ring 21”from Ring to fixture MINIMUM.

©2023 Tech Lighting, L.L.C. All rights reserved. The Tech Lighting logo is a registered trademark of Tech Lighting.
Tech Lighting reserves the right to change specifications for product improvements without notification.

• 7400 Linder Ave., Skokie, IL 60077
• T 847.410.4400 | F 847.410.4500
• www.visualcomfort.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>