Toucan TVDP05GR Pro Wireless Video Doorbell Instruction Manual
- May 15, 2024
- Toucan
Table of Contents
Toucan TVDP05GR Pro Wireless Video Doorbell
Specifications
- Model: TVDP05GR
Items Included
- USB Charging Cable
- AA Batteries
- Mounting Tape
- Wireless Chime
- Screwdriver
- Doorbell Screws
- Wall Anchors
- Mounting Plate
- Wiring Kit
- Wireless Video Doorbell PRO Thank You Card
- Warranty Card
- Manual
Get to know your video doorbell and chime:
Doorbell
- Camera lens
- Microphone
- Light sensor
- Doorbell button
- Speaker
- SET / Power ON button
- RST / Power OFF pinhole button
- Charging port
- (Optional) Power Terminals
Chime
- LED indicator
- SET button
- Speaker
Charge your video doorbell
- Open the back cover of the video doorbell.
- Plug in the micro USB cable to charge the video doorbell.
- It is recommended to fully charge the device before the first use.
Setup your video doorbell
- Download the Toucan App for Android or iOS.
- Scan QR code or visit www.toucansolution.com/pages/toucan-smart-home-app.
- Open the app and create a free account.
We Make Security Easy
Wireless Video Doorbell PRO MANUAL
Items Included
Get to know your video doorbell and chime
Doorbell
-
Camera lens
-
Microphone
-
Light sensor
-
Doorbell button
-
Speaker
-
SET / Power ON button
-
RST / Power OFF pinhole button
-
Charging port
-
(Optional) Power Terminals
Chime -
LED indicator
-
SET button
-
Speaker
Setup your video doorbell
-
Download the Toucan App for Android or IOS
Scan QR code or visit
www.toucansolution.com/pages/toucan-smart-home- app -
Open the app and create a free account
-
Tap the ‘+’ in the upper right to add a device
-
Press and hold the SET button until LED light blinks to enter the setup mode
-
Follow the instructions on the Toucan App to complete the setup
Pairing your chime with your video doorbell
The chime and doorbell come pre-paired, but if you need to pair it again, follow the instructions in this section.
- Press and hold the SET button on the Chime until the LED blinks, about 3 seconds
- Press and hold the doorbell button for about 3 seconds to complete pairing with the chime
Install your video doorbell and chime
-
Drill holes for wall anchor placement. If installing to use existing doorbell wiring, the hole in the center of the mounting plate should be over the old doorbell wiring hole.
-
Insert wall anchors
-
Attach the mounting plate with included screws
If connecting the Wireless Video Doorbell Pro to your existing doorbell wiring, proceed to the “(Optional) Wiring your video doorbell” section on the next page. Otherwise, continue with step 4 -
Place the doorbell on the mounting plate
-
Tighten the securing screw by turning it clockwise
-
If using the “(Optional) Wiring your video doorbell”, you may now turn the power back on for the doorbell wiring.
-
Place the adhesive tape on the back of the chime and stick it to the wall in a suitable location inside your home.
- If using the adhesive to mount the doorbell, please adhere to the surface and wait 24-48 hours to enable maximum bond strength before adding the doorbell. Apply 3M adhesive to dry surfaces only.
- You can mount the doorbell using just the adhesive on UPVC, wooden or smooth surface door frames (not suitable for brick or stone)
- The Chime can be placed up to 50m from the doorbell
(Optional) Wiring your video doorbell
This section should be followed ONLY if you are using existing doorbell wiring, and only after completing steps 1 through 31 in the “Install your video doorbell and chime” section
-
ENSURE THAT YOU HAVE TURNED OFF ALL POWER TO DOORBELL WIRING AT YOUR BREAKER BOX
-
Pull a few inches of doorbell wiring through the mounting plate
-
Twist ends of each doorbell wire together with the wire end of a connector
-
Place a wire nut over each pair of twisted wires, and turn nut clockwise to tighten
-
Slide the U-shaped ends of the connectors under the screws in the back of the doorbell. Tighten screws so that connectors do not slip out.
-
Push excess wires back into the wall
Return to Step 4 in the section “Install your video doorbell and chime” For a detailed setup procedure, please refer to the Toucan website www.ToucanSolution.com
Regulations & Compliance
Fcc Statement
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
ISED Regulatory Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
For additional info, visit our website at
ToucanSolution.com
VuPoint Solutions, Inc. (USA):
710 Nogales Street, City of Industry, CA 91748
VuPoint (Europe) Company Limited:
Innovation Center, Longbridge Technology Park, Longbridge, Birmingham B31 2TS
facebook.com/toucansmarthome
Instagram.com/toucansmarthome
Youtube.com/c/toucansmarthome
©2022 VUPOINT SOLUTIONS, INC. All Rights Reserved.
The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint
Solutions Inc. in the United States and other countries. App Store is a
registered trademark of Apple Inc. iOS is a registered trademark of Cisco
Technology, Inc. in the U.S. and other countries and is under license. Android
and Google Play are registered trademarks of Google LLC. Product names, logos,
brands and other trademarks referred to herein are the property of their
respective trademark holders. All trademarks remain the property of their
respective holders, and are used only to describe the products or services
being provided. These trademark holders are not affiliated with VuPoint
Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Inc’s
products or services.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>