Heath Zenith 18000150 Wireless Battery Doorbell Kit User Manual

Heath Zenith 18000150 Wireless Battery Doorbell Kit

Product Information

• Product Name: Wireless Battery Doorbell Kit
• Safety Information: To prevent possible serious injury or death, never allow small children near batteries. If a battery is swallowed, seek immediate medical attention. Do not dispose of batteries in fire as they may explode or leak.

Specifications

• 1x Doorbell Chime
• 1x Doorbell Button
• 4x Screws
• Batteries not included: 3 AA batteries for chime, CR2032 3V battery for button
• Code: 100M and 12E

Facility

Installing the Doorbell Chime Batteries
Insert 3 AA batteries into the doorbell chime with the positive pole facing outward and the negative pole facing inward. Ensure proper alignment to make the doorbell chime work effectively.

Mounting the Doorbell Button
Use screws or double-sided tape to mount the doorbell button. Do not permanently mount it until both the doorbell button and chime are working correctly.

Adjusting the Doorbell Chime Volume
The doorbell chime has a volume control button on the side. Press and release the button to adjust the volume incrementally.

Selecting a Tune
You can choose from ten pre-loaded tunes for your doorbell chime. Press the tune button to cycle through the options until you find your preferred tune.

Operation

• Doorbell Button Code Conversion and Low Battery Notification
  If needed, replace the batteries in the doorbell button when it rings Ding- Dong 3 times and the indicator light stays on for 10 seconds. For the chime, replace batteries when it rings Ding-Dong 5 times and the light flashes quickly for 10 seconds.

Frequently Asked Questions (FAQ)

• Q: How can I tell if the batteries need to be replaced?
  A: The doorbell button will ring Ding-Dong 3 times and the light will stay on for 10 seconds when the battery is low. For the chime, it will ring Ding-Dong 5 times and the light will flash quickly for 10 seconds.

SAFETY INFORMATION

WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near batteries. If a battery is swallowed, seek immediate medical attention.
WARNING: Do not dispose of batteries in fire. Batteries may explode or leak.

PACKAGE CONTENTS AND SPECIFICATIONS

INSTALLATION

INSTALLING THE DOORBELL CHIME BATTERIES

• Push the battery cover tab toward the battery cover (1)and pull to remove.
• Install 3 “AA” alkaline batteries (not included) into the doorbell chime (A).
• Make sure batteries are installed according to the diagram inside the doorbell chime.
• Replace the battery cover onto the DOORBELL CHIME (A).

INSTALLING THE BATTERY TO DOORBELL BUTTON

• Rotate the battery cover and remove it (B).
• Insert the battery according to the direction shown in the figure, with the positive pole facing outward and the negative pole facing inward.

TESTING THE DOORBELL BUTTON AND DOORBELL CHIME

• Temporarily position the doorbell button where it will be mounted.
• Press the doorbell button to verify the doorbell chime and doorbell button work properly.
• If the doorbell chime does not sound, move the doorbell chime closer to the doorbell button and test again.
  NOTE: Do not permanently mount the doorbell button until the doorbell button and doorbell chime are working properly.

NOTE: The doorbell button and doorbell chime come synced from the factory. The range of the wireless doorbell chime can vary with location, temperature, and battery condition. Test the doorbell button to ensure the doorbell chime and doorbell button are working properly.

MOUNTING THE DOORBELL BUTTON
Use either screws or double-sided tape to mount the doorbell button.

• To mount with screw, remove the back of the doorbell button by pushing in the tab on the bottom with a small screwdriver. Place the doorbell button back on the door jamb and mark the two screw holes. Attach with screws and snap on the front of the doorbell button.
• When attaching the doorbell button with double-sided tape, remove the paper from both sides of the double-sided tape and apply to a clean surface.

MOUNTING THE DOORBELL CHIME

• Use two of the screws to mount the doorbell chime.
• Determine mounting location.
• Drill two 7/32 in. (5.5 mm) pilot holes and insert wall anchors.
• Insert the screws into the wall anchors leaving about 1/8 in. (3.2 mm) of the screw threads exposed.
• Hang the doorbell chime on the screws using the keyhole on the back of the doorbell chime.

OPERATION

ADJUSTING THE DOORBELL CHIME VOLUME
The doorbell chime has an adjustable volume control located on the side. Press and release the volume adjust button to adjust the volume one step at a time.

MUTING THE DOORBELL CHIME

• Press and release the “Tune” button and “Volume” button at the same time, the light will flash 4 times with no sound, indicating that the doorbell chime is muted. When the doorbell chime is muted, press the synced doorbell button, the light of the doorbell chime will flash for 4 times.
• When the doorbell is muted, press and release the “Volume” button or “Tune” button to unmute the doorbell chime. The tune and volume will be restored to the status before muting.

SELECTING A TUNE
The doorbell chime allows you to customize your doorbell chime tunes. The doorbell chime has ten pre-loaded selectable tunes.

• Press and release the “Tune” button until the desired tune is heard.
• While the desired tune is playing, press the doorbell button to lock in the selected tune.

NOTE: Each doorbell button can be assigned its own unique tune.
NOTE: To listen to the selected tune, press and release the “Tune” button.
NOTE: Doorbell chime is designed to work with up to 10 wireless

Heath Zenith® doorbell buttons (sold separately).

SELECTABLE TUNES

• Auld Lang Syne
• Beethoven’s 5th
• Birthday Celebration
• Ding-Dong
• Relax Triplet
• Shorty
• We wish you a merry Christmas
• Short Westminster
• Westminster
• Huntington

SELECTING THE DOORBELL CHIME LIGHT

• The doorbell chime has 8 selectable light colors.
• Press and release the “Light” button to select the desired color.
• When the doorbell button is pressed, the doorbell chime will ring and the light will flash 4 times.

DOORBELL BUTTON CODE CONVERSION AND LOW BATTERY NOTIFICATION (ONLY WHEN REQUIRED)

• Code conversion

  • Doorbell button and doorbell chime default code pattern: 100M.
  • There is no need to convert the code for the first time using.
  • Press the silicone button in the back for 3 seconds, the indicator light of the doorbell button will flash quickly once, it indicates the doorbell button has been converted to the 12E code.
  • Press the silicone button in the back for 3 seconds, the indicator light of the doorbell button will flash for 3 seconds. It indicates the doorbell button has been converted to 100M code.
  • Press the silicone button in the back for 3 seconds, the code can be converted between 100M and 12E.
    NOTE: Only if the code of the doorbell button and doorbell chime is consistent, the doorbell button and doorbell chime will be working properly.

• Low battery notification

  • After press the doorbell button, the doorbell chime prompts “Ding-Dong” 3 times and the indicator light of the doorbell chime will remain on for 10 seconds, this indicates that the doorbell button battery is low, you need to replace with new batteries for doorbell button.

DOORBELL CHIME CODE CONVERSION AND LOW BATTERY NOTIFICATION (ONLY WHEN REQUIRED)

• Code conversion

  • Doorbell button and doorbell chime default Code pattern: 100M.
  • There is no need to convert the code for the first time using.
  • After the power is turned on for about 3 seconds, the doorbell chime prompts “Ding,” meaning the doorbell chime code is 100M. Within one minute, press and hold the “Volume” button and “Tune” button of the doorbell chime at the same time for about 10 seconds, and then you will hear the prompt sound “beep-beep,” then release the buttons, the doorbell chime will prompt “Ding-Dong,” which indicates that the doorbell chime has been converted to the 12E code. In this pattern, we should use 12E code doorbell button to sync and pairing.
  • After the power is turned on for about 3 seconds, the doorbell chime prompts “Ding-Dong”, meaning the doorbell chime code is 12E. Within one minute, press and hold the “Volume” button and “Tune” button of the doorbell chime at the same time for about 10 seconds, and then you will hear the prompt sound “beep-beep,” after release the buttons, the doorbell chime will prompt “Ding” which indicates that the doorbell chime has been converted to the 100M code. In this pattern, we should use 100M code doorbell chime button to sync and pair.
    NOTE: Only if the code of doorbell button and doorbell chime is consistent, the doorbell button and doorbell chime will be working properly. You will need to re-sync and pair after code conversion.

• Low battery notification

  • After pressing the doorbell button, the doorbell chime prompts “Ding-Dong” 5 times and the indicator light of the doorbell chime will flash quickly for 10 seconds, indicates that the doorbell chime battery is low, you will need to replace them with new batteries.

TROUBLESHOOTING

PROBLEM #1
The doorbell chime does not sound.

• POSSIBLE CAUSE:
  • A. The batteries are not installed correctly.
  • B. The batteries are dead.
  • C. The doorbell button and doorbell chime are not synced.
  • D. The code of doorbell button doesn’t match the code of doorbell chime.
• SOLUTION:
  • A. Make sure the batteries are installed according to the diagram inside the doorbell button and doorbell chime.
  • B. Check the charge of the doorbell button and doorbell chime batteries and replace them if necessary.
  • C. Sync the doorbell button and doorbell chime:
  • Press and hold the “Tune” button on the doorbell chime until the doorbell chime prompts a “beep-beep.”
  • Press the doorbell button within 10 seconds. The doorbell chime will prompt a “beep-beep” tone to indicate the doorbell button is synced.
  • Press the doorbell button to ensure operation.
  • D. Ensure the code of the doorbell button matches the code of the doorbell chime. To ensure operation,they will both need to be in 100M code or 12E code. Refer to Operation steps 4 and 5 for more information.

PROBLEM #2
The batteries seem okay, but the doorbell chime does not work after installation.

• POSSIBLE CAUSE:
  • A. Doorbell chime or doorbell button is mounted on metal or near metal studs.
  • B. Doorbell chime is mounted near a concrete floor or wall.
  • C. Doorbell chime and doorbell button are installed too far apart.
• SOLUTION:
  • A. Metal reduces transmission range. Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to move the doorbell chime or doorbell button away from the metal surface.
  • B. Concrete may reduce range. Move the doorbell chime away from the concrete surface.
  • C. Locate the doorbell chime closer to the doorbell button.

PROBLEM #3
Doorbell chime sounds when not intended (false triggers).

• POSSIBLE CAUSE:
  • A. Doorbell chime is receiving interference from another wireless device.
• SOLUTION 1:
  • A. Convert the doorbell button and doorbell chime to 100M code (see step 4 and 5 of operation).
• SOLUTION 2:
  • A. If the doorbell button and doorbell chime are in 12E code, follow the below instructions:
  • Remove the doorbell button battery. Wait 30 seconds.
  • Press and hold the doorbell button for 10 to 15 seconds within 60 seconds after installing the battery into the doorbell button.
  • Press and hold the “Tune” button on the doorbell chime until the doorbell chime prompts a “beep-beep-beepbeep.”
  • To re-sync the doorbell button and doorbell chime, press and hold the “Tune” button on the doorbell chime until the doorbell chime prompts a “beep-beep.”
  • Press the doorbell button within 10 seconds. The doorbell chime will prompts a “beep-beep” tone to indicate the doorbell button is synced.
  • Press the doorbell button to ensure operation

PROBLEM #4
The new doorbell button and doorbell chime do not work with existing doorbell buttons and doorbell chimes.

• POSSIBLE CAUSE:
  • A. The new doorbell button and doorbell chime are not using the same codes as existing doorbell buttons and doorbell chimes.
• SOLUTION:
  • A. Ensure the code of the doorbell button matches the code of the doorbell chime. To ensure operation, they will both need to be in 100M code or 12E code. Refer to Operation steps 4 and 5 for more information. Please call 1-888-543 1388 for assistance in changing the codes to work with the existing doorbell buttons and doorbell chimes.

WARRANTY

1-YEAR LIMITED WARRANTY

• This product is guaranteed to be free of factory defective parts and workmanship for a period of 1 year from date of purchase. Purchase receipt is required for all warranty claims.
• This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components that a customer uses in conjunction with this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

FCC Responsible Party:
Globe Electric
2264 East 6th Street
San Bernardino, CA 92410
www.globe-electric.com

The illustrations may vary from the actual product. Before returning to the store, please contact our support team for assistance at 1-888-543-1388.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>