PITTSBURGH 58807 12V Twin Disc Car Horn Owner’s Manual
- October 30, 2023
- PITTSBURGH
Table of Contents
58807 12V Twin Disc Car Horn
Owner’s
Manual
58807 12V Twin Disc Car Horn
When unpacking, make sure that the product is intact and undamaged. If any
parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright© 2022 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described
herein.
Tools required for assembly and service may not be included.
WARNING
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Specifications
| Power Requirement | 12 Volts DC |
|---|---|
| Volume | 108dB each |
IMPORTANT SAFETY INFORMATION
-
Install a 15 amp fuse (not included) inline on the power supply wire of this item. Using no fuse, or using an incorrect fuse can cause an electrical fire.
-
Install only according to these instructions. Improper installation can create hazards.
-
Wear ANSI-approved safety goggles and heavy-duty work gloves during installation.
-
Do not install while engine is running. Remove ignition keys from vehicle and set parking brake.
-
When drilling holes, beware of any hidden electrical lines or cables. Make sure you don’t damage or weaken the structural integrity of the vehicle.
-
Keep assembly area clean and well lit.
-
Do not use as a replacement for Original Equipment Manufacturer (OEM) horn(s).
-
Do not install this product in a location that will exceed 212°F or get submerged in water. It may stop operating if exposed to any of those conditions.
-
Keep bystanders out of the area during installation.
-
Do not expose Horns to rain or wet conditions. Water entering the Horns will increase the risk of electric shock.
-
Do not install when tired or when under the influence of alcohol, drugs or medication.
-
Do not install this product yourself unless you are technically competent to do so. If necessary, have a qualified technician install the Horns.
-
This product is not a toy. Do not allow children to play with or near this item.
-
Use as intended only.
-
Inspect before every use; do not use if parts are loose or damaged.
-
Exposure to noise levels over 85 dB is hazardous to hearing. Everyone close enough to horn to be exposed to more than 85 dB must wear ANSIapproved hearing protection. Do not use Horn in close proximity to people or animals, as he decibel level may cause hearing damage.
-
Check and comply with local standards for noise pollution levels before use.
-
Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement. -
The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.
WARNING
Risk of serious personal injury. Turn the vehicle off and disconnect
battery before installation.
Note: If unsure about any aspect of installation, have the Horns
installed by a qualified mechanic.
-
Prior to installation, turn off the ignition, shift transmission into park (for automatic transmissions) or reverse (for manual). Remove ignition keys from vehicle and allow engine to cool. Place wheel chocks on both sides of at least two wheels. Disconnect the vehicle’s battery. Make sure the engine and engine compartment are cool before installation.
-
Select a suitable location to mount the Horns.
Location must shelter Horns from incoming rain, road water, and mud splash from under the vehicle. Do not mount Horns near hot engine components or where it may come into direct contact with hot surfaces or moving parts.
Note: Holes may need to be drilled in the vehicle chassis to mount the Horns and 12V Relay. Make sure no electrical wires or cables or any other obstructions or vehicle components are in the way of the drilling path.
Mount the Horns and 12V Relay to the vehicle’s chassis using Nuts and Bolts, (not included). Point the Horns forward and slightly down for maximum efficiency. -
Tighten Nuts to secure the Horns 12V Relay to the mounting location.
-
Make connections to the Horns and 12V Relay as shown on the Wiring Diagram using terminal connectors (not included) on all connections. Pay attention to polarity. For negative ground systems (most vehicles). For positive ground systems, have a qualified mechanic install the horn. Install a 15 amp fuse (not included) inline on the power supply wire of this item. Using no fuse, or using an incorrect fuse can cause an electrical fire.
Negative Ground Wiring Diagram
Parts List and Diagram
| Part | Description | Qty |
|---|---|---|
| 1 | 12V Relay | 1 |
| 2 | High-Tone Super tone Horn | 1 |
| 3 | Low-Tone Super tone Horn | 1 |
| 4 | Mounting Bracket | 2 |
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase
instead.
Note: Some parts are listed and shown for illustration purposes only, and are
not available individually as replacement parts. Specify UPC 193175446879 when
ordering parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may
not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we
may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost
of returning the product. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
Visit our website at: http://www.harborfreight.com
Email our technical support at:
productsupport@harborfreight.com
For technical questions, please call 1-888-866-5797.
26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Documents / Resources
|
PITTSBURGH 58807 12V Twin Disc Car
Horn
[pdf] Owner's Manual
58807 12V Twin Disc Car Horn, 58807, 12V Twin Disc Car Horn, Twin Disc Car
Horn, Disc Car Horn, Car Horn
---|---