URC UR3L-SR4 Subscription Broadcast Remote Control User Manual

: June 5, 2024
: URC

URC UR3L-SR4 Subscription Broadcast Remote Control

Introduction
This remote control is designed to operate most IPTV and DTA STBs as well as Digital and Analog Cable Boxes.

Replacing Batteries

Before you program or operate the remote control, you must install two new AAA alkaline batteries.

STEP1 Remove the battery compartment cover from the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.

Button Functions

Programming the Remote Control

*Note: In this section, when you are instructed to press a [DEVICEJ buton, that means you should press either the
CBL, TV, or DVD button, depending on which device you are programming the remote to operate.

Quick Set-Up Method

STEP) Turn on the component you want to program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the power button. If it
Repeat the steps above for all compo-nents. (CBL, TV, DVD).
BB.. QQuuiicckk SSeett–uupp CCooddee TTaabblleess

CBL

Quick Number	Manufact urer/Brand
0	PACE DTA
1	SA/CISCO, SAMSUNG, PACE DIGITAL
2	MOTOROLA DIGITAL
3	MOTOROLA DTA
4	EVOLUTION DTA
5	CISCO IPTV
6	ADB IPTV
7	TECHNICOLOR
8	AMINO 140/540 IPTV
9	MOTOROLA IPTV

TV

Quick Number	Manufacturer/Brand
0	SANYO
1	SONY
2	SAMSUNG
3	LG
4	TOSHIBA
5	PANASONIC
6	PHILIPS
7	HITACHI
8	SHARP
9	VIZIO

DVD

Quick Number	Manufacturer/Brand
0	HITACHI
1	SONY
2	PHILIPS
3	SAMSUNG
4	PHILIPS MAGNAVOX
5	PANASONIC
6	LG
7	JVC
8	DENON
9	PIONEER

Manual Program

The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.

STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD) .
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultane-ously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
STEP4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.

AUTO SEARCH METHOD

If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:

STEP1 Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD).
STEP2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on.
STEP3 Press the [CH ] or [CH ] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH5] or [CH6] button as soon as the equipment turns off.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.

To find the Three-Digit Code that Vwas Hogrammed using the Auto Search

Method

STEP1 Press the appropriate [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off.

Programming a Second TV to the DVD Button

STEP1) Press the [DVD] button andthe [OK/SELY button simutane- ously for 3 seconds. The DVD LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 ) Point the remote control toward the IV and enter the three-digit code for your TV from the TV codes table.
STEP 4 Store the three-digit code by pressing the [DVDJ button. The device LED will blink twice to confirm that the code has been stored.

THE LEARNING METHOD

STEP1 Press the [Device] button (CBL, TV or DVD) to be programmed and the [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on.
STEP2 Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches apart.
STEP3 Press any button on the UR3L-SR4 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button.
STEP4 Press and hold the [MUTE] button on the other remote until the UR3L-SR4 Device LED light blinks twice.
STEP5 Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly.

Erasing a Single Learned Command

STEP1) Press the [Device) and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on.
STEP2) Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure.
STEP3 To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times.

Erasing AllLeamed Commands from One Device

STEP) Press the [DEVICE] and
INPUT buttons simultan
ously for 3 seconds until the
The device LED ight turns on.
STEP2) Press and hold both the
DEVICE button you want to
erase and the [PAUSEJ button
for 5 seconds. The Device LED
will blink twice to confim the
erasure.
STEP3 To exit, press and hold both the
DEVICE] and [INPUTJ buttons
simultaneously until the Device
LED blinks 3times.

Programming the All OiH Bauton

This allows you to program the All Off button so t can send up to three power On/Off commands with one button press.

STEP1) Press the [CBLJ button.
STEP2) Press the [Al OFF| button and the OKSELI button simultaneously
STEP3 Press the first [Device] button
you want to store in the [ALL OFF] button and then the [POWER] button. Repeat this for other Device until you have stored all the desired power commands into the [ALL OFF] button.
the power commands you stored. The [CBL] button will blink twice to confirm the Device have been saved. STEP4 Press the [CH ] button to save

Programming for Advanced unctions.

If your remote model has custom-programmable Macro buttons are available, they can be programmed to act as a Macro’ or Favorite Channel button in CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can he ac. cessed with one button press.

STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.
STEP3 Enter the 2, 3 or 4-digit code for the channel you want to be programmed first (for example, using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered.
STEP4 Press the [CH5] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands.

To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel.

To erase the Macro programming and return to the original function:

STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds. The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP3 Press the [CH5] button to erase the functions stored in the button. The CBL device LED will blink twice to confirm that the memory button has been erased.

Programming Volume Cantol

Volume and Mute control are factory-programmed to automatically transfer to the respective Device mode you select, as follows
CBL:TV TV:TV DVD:TV
If you wish to store the Cable volume control in CBLmode, use the following steps.

STEP1) Press the [OK/SELJ bustton and CBLJ button simultaneously three seconds. The device LED will tum on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL ] button. The device LED will blink.
STEP3 Press [CBL) button. The device LED will blink twice to confirm the programming.
Note: To return CBL device to TV volume repeat steps above replacing 1CBLI with [TV] in Step 3.

Programming Channel Control

Chanel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

CBL : CBL TV : CBL DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.

STEP1 Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL ] button. The device LED will blink.
STEP3 Press [TV] button. The device LED will blink twice to confirm the programming.

Low Battery Warning

When the battery is low (2.3V-20V) and needs to be replaced with fresh batteries, device LED ill blink 2 times in sequence whenever a |DEVICEJ button is pressed to tum on equipment

Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. For additional information about your remote control, go to www.universaremote.com

Set-up Code Tables

CABLE TV

CISCO/SA| EXPLORER Series| 001

007

---|---|---
8600X| 011
8600| 021
8540,8570,8590| 022
8500| 023
LogicTV| 209
U-VERSE| 251
MOTOROLA| DCT Series (DVR Model)| 002
DTA100| 206
U-VERSE, VIP1200, VIP1216, VIP1616T,

VIP1910, VIP1920, VIP1960, VIP1970

255

CABLE TV

		213
Kamai 651	221
Kamai 500	210

221

255

SOLARIS, NOVA

007

007

BA9000| 013
SAMSUNG| OCAP MODELS| 001

007

TV

ADMIRAL	072 096 081
ADVENT	147
AIWA	141 145
AKAI	070 146 148 124 226 104 108
AKIO	103
ALARON	028
AMARK	112
AMERICA ACTION	043
AMPRO	073
ANAM	043 054 056 080 112 131
AOC	058 070 112 616
APEX	092
APEX DIGITAL	150 037 015 724
AQUAVISION	097 100 686
AUDIOVOX	076 103 043 035 078 224
AUVIO	689
Avera	761
AVIELO	090
AVION	223
AXESS	711
BAYSONIC	043
BELL&HOWELL	072
BENQ	234
BRADFORD	043
BROKSONIC	096
CANDLE	070 002 003
CAPEHART	058
CARVER	164
CELEBRITY	001
CETRONIC	043
CIELO	714
Ciil	732
CINERAL	103 120
CITIZEN	070 002 003 101 103
CLASSIC	043
COBY	640 641 598
CONTEC	043 051
Continu-us	161 746 747
CRAIG	043 054 028
CROSLEY	164
CROWN	043
CURTIS MATHES	070 101 011 072 120 164 081
CXC	043
DAEWOO	076 103 112 043 120
DELL	041
---	---
DENON	011
DIGITAL PROJECTION	090
DUMONT	073
DWIN	131 132
DYNASTY	043
FISHER	007 057
ELECTROBAND	001
ELECTROHOME	024 076
ELEMENT	110 622 690
EMERSON	005 028 043 048 076 096 155

051 153 121

120 081

158 174 670 749

HP| 027 039 098
HUMAX| 122
HYPERION| 609
HYUNDAI| 049 067
ILO| 055 096
INFINITY| 164
INFOCUS| 046 215 225 233 726 733
INKEL| 129
INSIGNIA| 068 069 078 096 164 168 604 617
---|---
INTEQ| 073
JBL| 164
JCB| 001
JCPENNEY| 008 024 030 070 101 156
JENSEN| 013
JVC| 038 001 034 083 639
KENWOOD| 070 001
KLEGG| 220
KLOSS| 002 059
KREISEN| 202
KTV| 070 043
LG| 598 086 106 112 741
LODGENET| 072
LOEWE| 196 164 738
LOGIK| 072
LXI| 007 052 164 015 081
MAGNAVOX| 070 003 022 059 060 061 164 094

056 028 035 211 205 218 050 138

232

MAJESTIC| 072
MARANTZ| 164 070 143 169
MATSUI| 164
MATSUSHITA| 080
MAXENT| 165
MEMOREX| 007 072 028 096
MGA| 024 070
MIDLAND| 073
MINTEK| 077
MINUTZ| 008
MITSUBISHI| 024 040 146 028 124 200 235 081
MOTOROLA| 081
MTC| 070 101
MULTITECH| 043
NAD| 025 015
NEC| 070 040 056 007 019 024 717 758
NEXUS| 620 078
NIKEI| 043
NIKKO| 103
NIKO| 175
NORCENT| 211
NTC| 103
NUVISION| 084
OLEVIA| 219
ONKING| 043
---|---
onn.| 898
ONWA| 043
OPTIMUS| 080
OPTOMA| 029
OPTONICA| 019 081
ORION| 096 201 203 204 205 028
PANASONIC| 080 164 190 034 056 230 248 524

607 664 801

PEERLESS-AV| 723 763
PHILCO| 070 003 024 056 059 060 164
PHILIPS| 164 005 218 038 093 070 003 059

199 232 727 743 773

713 751

655

765 766

SHERWOOD| 128
SIGNATURE| 072
---|---
Silo| 001
Skyvue| 744
Skyworth| 895
SONY| 001 608 633
SOUNDESIGN| 003 028 043
SOYO| 163
SPECTRICON| 112
SQUAREVIEW| 052
SSS| 043
STARLITE| 043
SUPRE MACY| 002
SUPREME| 001
SUNBRITE| 633 634 635 236 605 772
SVA| 046
SYLVANIA| 070 003 059 060 164 056 168 121 231
SYMPHONIC| 052 168
SYNTAX OLEVIA| 219
TANDY| 081
TATUNG| 056
TCL| 705 749
TECHNICS| 034 080
TECHNOL ACE| 028
TECHVIEW| 246
TEKNIKA| 002 003 024 028 043 072 101 103 164
TELERENT| 072
TERA| 172
THOMPSON| 166
TNCI| 073
TOSHIBA| 015 101 045 030 007 040 142 137

703

074 070

W Box Technologies| 731
WESTINGHOUSE| 076 036 221 222 001 690 695
WINBOOK| 079
Manufacturer/Brand| Set-Up Code Number
---|---
YAMAHA| 070
YUPITERU| 043
ZENITH| 011 072 073 095 103 096
ZONDA| 112
Manufacturer/Brand| Set-Up Code Number
---|---
ADCOM| 203
AIWA| 210
AKAI| 239
APEX DIGITAL| 240 196
ARCAM| 165 148 374
BOSE| 244 245
CAMBRIDGE AUDIO| 224 145
COBY| 206
CYBERHOME| 170 212
DAEWOO| 170
DENON| 226 225 358
DURABRAND| 235
EMERSON| 235
ESA| 235
FUNAI| 235
GOLDSTAR| 182 194
GO VIDEO| 228 182 252 253 254
GRADIENTE| 243
HARMAN KARDON| 217
HITACHI| 181
INSIGNIA| 235 085 182 178 349 385
INTEGRA| 236 128
JVC| 185
KENWOOD| 166
KISS| 237
KLH| 230
KOSS| 243
KRELL| 218
LEXICON| 216
LG| 182 194 105 350
MAGNAVOX| 178 191 195 235 386
MARANTZ| 135
MCINTOSH| 167
MEMOREX| 222
MERIDIAN| 200
MINTEK| 240 196
MITSUBISHI| 186
MYRYAD| 211
---|---
NAD| 198 182 353
ONKYO| 207 236 128
OPPO| 125
OPTIMUS| 187
ORITRON| 243
PANASONIC| 076 219 103 104 379
PHILIPS| 195 164 191 209 127 381 387
PIONEER| 187 221 223 354 377
POLAROID| 085
RCA| 086
SANSUI| 201
SANYO| 215
SAMSUNG| 183 228 205 073 152 241 380
SENSORY SCIENCE| 254
SHARP| 174
SHERWOOD| 129 361
SONY| 168 190 213 077 118 119 120 121

126 351 368 378 382

DVR(TIVO)

Manufacturer/Brand	Set-Up Code Number
CHANNEL MASTER	841 859
DSTV	786 787 788 241 800
HUGHES	817
HUMAX	817
ICREALTIME	111 816
MOXI	112
PHILIPS	790 817 785
Manufacturer/Brand	Set-Up Code Number
---	---
RCA	809
REPLAY NETWORKS	775
SONY	804 805
Speco Technologies	879
TIVO	790 817 858
TOSHIBA	817
ZUUMMedia	855