GLACIER BAY HD67737-0001 Market Single Handle Pull Out Spryer Kitchen Faucet Installation Guide

GLACIER BAY HD67737-0001 Market Single Handle Pull Out Spryer Kitchen Faucet Installation Guide

Important Information

• Observe all local plumbing and building codes.
• Cover the sink drain to avoid losing any parts.
• Review the care and cleaning section included in this guide.

Warranty

LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective. Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434- 5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available for all Glacier Bay warranty claims.

This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the duration of warranty

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for more details.

Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.

Pre-Installation

PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package Contents list. If any part is missing or damaged, do not attempt to install the product. Contact Customer Service for replacement parts..

TOOLS AND HARDWARE REQUIRED

Adjustable wrench

Safety goggles

Silicone sealant

Pre-Installation (continued)

PACKAGE CONTENTS

Installation

Installing the faucet assembly

CAUTION: Always shut off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off.

• Shut off the water supply. Remove the old faucet. Clean the mounting surface.

  NOTE : This step is for no escutcheon installation (optional)

• Insert the faucet assembly (A) through the hole in the sink
  

NOTE : This step is for escutcheon installation (optional). A silicone is required under the gasket (E

• Place the escutcheon (D) and the gasket (E) on the bottom of the new faucet assembly (A).
• Insert the faucet assembly (A) through the hole in the escutcheon (D).
  

Installation (continued

Securing the faucet assembly

NOTE : Make sure that the face marked with the arrow on the anger (1) is facing forward.

• From underneath the sink, secure the faucet assembly to the sink with the Fast Mount™ system (B). Push the Fast Mount™ system (B) up over the threads until it stops against the bottom of the sink, then hand turn (clockwise) to tighten (Fig 1).
  

Attaching the quick connector to the receiving block

• Push the quick connector (C) rely upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.

Installing the weight

• Install the weight clip (G) at the point of the hose marking “weight here”.
• Insert the weight (F) onto the clip (G) by sliding it down onto the clip (G).
  ”

Making the water supply connections

NOTE : The hot side inlet tube is indicated by a label. Avoid twisting wires together or placing the wires close to each other and damaging.

• Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with a wrench. Do not over-tighten.
  

Operation

Flushing and checking for leaks

IMPORTANT : After installation is completed, turn on the hot and cold water supplies. Check for leaks. Do not lose the gasket (1) in the hose.

• Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet to the warm position where it mixes hot and cold water.
• Flush the water lines for one minute. This ushers away any debris that could cause damage to internal parts. Check for leaks.
• Re-tighten any connections if necessary, but do not overtighten. Reinstall the spray head by hand tightening it back onto the spray hose in a clockwise direction.
  

Removing the quick connector

• If it is necessary to remove the quick connector (1), squeeze the tabs (2) on the quick connector and then pull down to disconnect.

Care and Cleaning

• To clean, wipe down with a damp cloth and dry with a towel.
• Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will be voided.

Troubleshooting

NOTE : Refer to the service parts section in this manual for a detailed drawing showing the location of the parts listed below.

•  Use wrench to retighten the bonnet nut sufficiently. Do  not over-tighten. Clean or replace the O-ring.

The aerator leaks or has an inconsistent water flow pattern.| The aerator is dirty or miscited. The cartridge may be clogged.|

• Remove the aerator and check for debris in the aerator screens.
• Remove the cartridge and check for debris
• Ensure the aerator is properly installed.

There are leaks from the hose underneath the deck.| The hose and discharge tube connection may be loose.|

• Tighten the connection between the discharge tube and hose.

The hose does not retract.| The weight is not installed in the appropriate position.|

• Reinstall or readjust the weight.

The water pressure is low.| The connector underneath the deck is clogged with debris.
The aerator is clogged.|

• Turn off the water supply and disconnect the connector / aerator
• .Unscrew the connector / aerator and clean under running water
• Screw the connector / aerator back.
• Test water flow. If water pressure is still low then replace the connector / aerator.

There is no hot or cold water.| The water inlet hose was accidentally kinked during installation and is limiting the water flow through.|

• Reinstall the water inlet hose.

There is a low flow of water.| The screen filter in the spray head is dirty.|

• Turn off the water supply at angle stop and unscrew the spray head from spray hose.
• Clean the screen filter in the spray head under running water.

Service Parts

Specify Finish

Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>