GLACIER BAY HD67551 Single Handle Pull Down Sprayer Kitchen Faucet Installation Guide
- May 15, 2024
- GLACIER BAY
Table of Contents
GLACIER BAY HD67551 Single Handle Pull Down Sprayer Kitchen Faucet
Product Information
Specifications
- Model: MARKET SINGLE-HANDLE PULL-DOWN SPRAYER KITCHEN FAUCET
- SKU: 325268741 HD67551-0301 1009547701
- Internet #: 323776470 HD67551-0308D2 1009230534
Product Usage Instructions
Pre-Installation
Planning Installation:
Before starting the installation process, ensure all parts are present. Compare the parts with the Package Contents list provided. If any part is missing or damaged, do not proceed with the installation. Contact Customer Service for replacement parts.
Tools and Hardware Required:
- Silicone
- adjustable wrench
- safety goggles
- Silicone sealant
Package Contents:
- A – Faucet assembly
- B – FastMount™
- C – Quick connector
- D – Escutcheon
- E – Gasket
- F – Weight
- G – Weight clip
Installation
- Follow the step-by-step installation guide provided in the manual.
- Securely attach the faucet assembly to the sink following the provided instructions.
- Use the silicone sealant to ensure a watertight connection.
- Check for any leaks before finishing the installation.
operation
Once installed, use the single-handle pull-down sprayer kitchen faucet by adjusting the handle for water flow and temperature control. Pull down the sprayer for extended reach and flexibility in washing dishes or other kitchen tasks.
Care and Cleaning
Regularly clean the faucet with a mild soap solution and a soft cloth to maintain its appearance. Avoid harsh chemicals that may damage the finish. Refer to the care and cleaning section in the manual for specific instructions.
Troubleshooting
If you encounter any issues with the faucet’s operation or performance, refer to the troubleshooting section in the manual for common problems and solutions. If problems persist, contact Customer Service for assistance.
FAQ
Q: What should I do if I encounter a leak after installation?
A: Check all connections for tightness and ensure that the silicone sealant is properly applied. If the leak persists, contact Customer Service for further assistance.
Q: Can I use this faucet for commercial purposes?
A: This faucet is designed for residential use.
Commercial use is not covered under the warranty terms. For commercial
applications, consider a faucet specifically rated for such use.
Internet
- 325268741
- 323776470
- 323777021
- 323776231
- 323776045
- 324555891
Model
- HD67551-0301
- HD67551-0308D2
- HD67551-0306
- HD67551-0327H2
- HD67551-0310H
- HD67551-034405
SKU
- 1009547701
- 1009230534
- 1009215011
- 1009230516
- 1009015417
- 1009368886
MARKET SINGLE-HANDLE PULL-DOWN SPRAYER KITCHEN FAUCET
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service 8 a.m. – 7
p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
THANK YOU
We appreciate the trust and confidence you have placed in Glacier Bay through
the purchase of this kitchen faucet. We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line
of products available for your home improvement needs. Thank you for choosing
Glacier Bay!
Important Information
- Observe all local plumbing and building codes.
- Cover the sink drain to avoid losing any parts.
- Review the care and cleaning section included in this guide.
Warranty
LIMITED LIFETIME WARRANTY
- Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective. Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available for all Glacier Bay warranty claims.
- This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended a five year limited warranty from the date of purchase, with all other terms of this warranty applying except the duration of warranty.
- Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for more details.
- Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are
present. Compare parts with the Package Contents list. If any part is missing
or damaged, do not attempt to install the product. Contact Customer Service
for replacement parts..
TOOLS AND HARDWARE REQUIRED
PACKAGE CONTENTS
Part | Description | Quantity |
---|---|---|
A | Faucet assembly | 1 |
B | FastMount™ | 1 |
C | Quick connector | 1 |
D | Escutcheon | 1 |
E | Gasket | 1 |
F | Weight | 1 |
G | Weight clip | 1 |
Installation
Installing the faucet assembly
CAUTION: Always shut off the water supply before removing an existing faucet or replacing any part of a faucet. Open the faucet handle to relieve water pressure and ensure that the water is completely shut off.
NOTE: This step is for no escutcheon installation (optional). If the escutcheon will be used, install the faucet assembly as described in step 2.
- Shut off the water supply.
- Insert the faucet body through the hole in the sink.
Installing the faucet assembly
NOTE: This step is for escutcheon installation (optional). If the escutcheon will not be used, install the faucet assembly as described in step
- Place the escutcheon (D) and the gasket (E) on the bottom of the new faucet assembly (A).
- Insert the faucet assembly (A) through the hole in the escutcheon (D).
- NOTE: Silicone sealant is required under the gasket (E).
Securing the faucet assembly
From underneath the sink, secure the faucet assembly to the sink with the FastMount™ system (B). Push the FastMount™ system (B) up over the threads until it stops against the bottom of the sink, then hand turn (clockwise) to tighten (Fig 1).
Attaching the quick connector to the receiving block
Push the quick connector (C) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.
Installing the weight
- Install the weight clip (G) at the point of the hose marking “weight here”.
- Insert the weight (F) onto the clip (G) by sliding it down onto the clip (G).
Making the water supply connections
NOTE: The hot side inlet tube is indicated by a label. Avoid twisting wires together or placing the wires close to each other and damaging.
Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with a wrench. Do not over-tighten.
Operation
Flushing and checking for leaks
IMPORTANT: After installation is completed, turn on the hot and cold water supplies. Check for leaks.
- Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet to the warm position where it mixes hot and cold water.
- Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks.
- Re-tighten any connections if necessary, but do not overtighten. Reinstall the spray head by hand tightening it back onto the spray hose in a clockwise direction.
Removing the quick connector
If it is necessary to remove the quick connector (1), squeeze the tabs (2) on the quick connector and then pull down to disconnect.
Care and Cleaning
- To clean, wipe down with a damp cloth and dry with a towel.
- Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will be voided.
Troubleshooting
NOTE: Refer to the service parts section in this manual for a detailed drawing showing the location of the parts listed below.
Problem | Possible Cause | Solution |
---|---|---|
There are leaks underneath the handle. | The bonnet nut has come loose and the |
o-ring on the cartridge is dirty or damaged.
| □ Use wrench to retighten the bonnet nut sufficiently.
Do not over-tighten.
Clean or replace the o-ring.
The aerator leaks or has an inconsistent water low pattern.| The aerator is dirty or misfitted. The cartridge may be clogged.| □ Remove the aerator and check for debris in the aerator screens.
□ Remove the cartridge and check for debris.
□ Ensure the aerator is properly installed.
There are leaks from the hose underneath the deck.| The hose and discharge
tube connection may be loose.| □ Tighten the connection between the discharge
tube and hose.
The hose does not retract.| The weight is not installed in the appropriate
position.| □ Reinstall or readjust the weight.
The water pressure is low.| The connector underneath the deck is clogged with
debris.
The aerator is clogged.
| □ Turn off the water supply and disconnect the connector
/ aerator.
□ Unscrew the connector / aerator and clean under running water.
□ Screw the connector / aerator back.
□ Test water low. If water pressure is still low then replace the connector / aerator.
There is no hot or cold water.| The water inlet hose was accidentally kinked
during installation and is limiting the water low through.| □ Reinstall the
water inlet hose.
There is a low low of water.| The screen filter in the spray head is dirty.| □
Turn off the water supply at angle stop and unscrew the spray head from spray
hose.
□ Clean the screen filter in the spray head under running water.
Service Parts
Part | Description | Part Number |
---|---|---|
1 | Spray head and Hose | RP38567* |
2 | O-ring | RP60006 |
3 | Wearable ring | RP64220 |
4 | Cartridge | RP20044 |
5 | Bonnet nut | RP70528 |
6 | Cap | RP80503* |
7 | Screw | RP50015 |
8 | Handle | RP13433* |
9 | Set screw | RP50002 |
10 | Block | RP70421 |
Part | Description | Part Number |
--- | --- | --- |
11 | O-ring | RP60002 |
12 | Quick connect assembly | RP70697 |
13 | O-ring | RP60089 |
14 | Weight | RP70689 |
15 | Weight clip | RP70590 |
16 | Escutcheon | RP80544* |
17 | Gasket | RP80545 |
18 | FastMount™ | RP56096 |
*Specify Finish
Many replacement cartridges, aerators, and drain assemblies can be purchased at your local The Home Depot store or online at HOMEDEPOT.COM
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service 8 a.m. – 7
p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Retain this manual for future use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>