Televes 769214 SFP Plus 10GbE LC UPC Duplex SMF Instruction Manual
- May 15, 2024
- Televes
Table of Contents
SFP+ 10GbE LC/UPC Duplex SMF Module
Ref. 769214 (EKASFPPLUS2F)
Important safety Instructions
Safe installation
-
Read these instructions before handling or connecting the equipment. Keep these instructions. Heed all warnings. Follow all instructions.
-
Clean only with dry cloth.
-
Do not use this apparatus near water. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as glasses, shall be placed on the apparatus.
-
Do not place the equipment in a highly humid environment.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not place naked # ames, such as lighted candles on or near the product. -
Do not placethe equipment in a place where it can su$ er vibrations or shocks.
Optical connection instructions
- LC/UPC single-mode fiber cable must be used.
- Keep the connectors lids and cable caps for future removal /protection operations.
- Carefully align the guides on both connectors when plugging a cable to the device, then push the connector all the way in.
- Takespecial care to avoid damaging theunp rotected ends of the connectors, as smallscratches, impurities and/or p articles of dirt, oil, grease, sweat, etc. may signifi cantly a set the qualityof the signal.
- To clean the ends of the connectors, gently rub with a lintfree lens cleaningcloth, dampened using additive-free isopro pyl alcohol.
- Makesurethe alcohol evaporates fully before conne cting. Keep the connector covers and cable caps in a safe place in case they are needed in the future.
- Always fit the covers on the connectors of devices that are not connected to cables to prevent the laser beam from damaging the eyes. Do not turn the transmitter on without a fiber optic cable connected to it.
Safety measures
Warning.-
This product emits an invisible laser beam. Avoid contact with laser
radiation. The use of equipment such as binoculars or magnifying glasses may
increase damage caused to the eyes.
Caution.
- The use of theequipment in any other way than the specified in this manual may lead to exposure to harmful radiation.
- Do not use the equipment in any way that does not comply with the operating instructions or in any conditions that exceed the stipulated atmospheric specifications.
- The user cannot service this equipment. For technical assistance, contact our technical assistance department.
- Never point the laser beam at people or animals.
According to: 60825-1: 2014
| 769214
---|---
Maximum Output| 0,5 dBm
Emitted Wavelength| 1310 nm
| Equipment designed for indoor use
---|---
****| The equipment complies with the requirements of the CE mark
| The equipment complies with the requirements of the CMIN mark
The Ref. 769214 series transceiver is a high performance, costeective module
that supports data-rate of 10.3125 Gbps and transmission distance up to 10 km.
The transceiver meets the Small Form-factor Pluggable (SFP) utilizing an
LC/UPC Duplex connector.
Main Features
- Data-Rate of 10.3125 Gbps
- 1310 nm DFB laser and PIN photodetector
- LC/UPC Duplex connector
- Digital Diagnostic Monitoring (DDM)
- 10 km transmission with 9/125 m SM ! ber
Applications
- Gigabit Ethernet
- Switch to switch interface
- Router/Server interface
- Other optical transmission sytems
| Technical specifications | 769214 EKASFPPLUS2F | |
|---|---|---|
| Min. | Typical | Max. |
| Power consumption | W | – |
| Supply voltage | V | 3,14 |
| Operating temperature | ºC | 0 |
| Connectors | Type | LC/UPC DUPLEX |
Transmitter
Center wavelength| nm| 1260| 1310| 1355
Transmitter| Type| DFB
Launch Power| dBm| -8,2| –| 0,5
Receiver
Center wavelength| nm| 1260| –| 1610
Receiver| Type| –| PIN Photod| –
Sensitivity| dBm| -15| –| –
Overload| dBm| –| –| 0,5
Typical Application
DECLARATION OF CONFORMITY
https://doc.televes.com
Manufacturer
Televes S.A.U. Spain www.televes.com
2023 © Copyright, Televés S.A.U.