HOLMAN 5L EzySpray Free Garden Sprayer Installation Guide

May 15, 2024
Holman

HOLMAN 5L EzySpray Free Garden Sprayer - icon 1

INTRODUCTION

The portable and lightweight HOLMAN EzySpray® is an essential tool for your garden maintenance. The patented pre-pressurised air tank requires no manual pumping–connect your garden hose, fill the reservoir, and away you go!
A standard garden spray would require manual pumping roughly 1,250 times for 50L of spraying; the EzySpray ® doesn’t need a single pump.
To fill your EzySpray® , simply connect a garden hose to the tank. The gauge indicates how full the tank is, and the spray wand gives all the control you need.
Adding fertiliser, herbicide or other additives to your EzySpray® is easy. Unhook the handle, and pour in concentrate before filling with water.
For more info and support, visit www.holmanindustries.com.au

COMPONENTS

A. SPRAY HEAD
B. WAND
C. TRIGGER
D. HOSE
E. EzySpray® PRESSURE TANK
F. WAND THREAD
G. LOCKING NUT
H. TANK OUTLET
I. PRESSURE GAUGE
J. SCHRADER VALVE
K. 12mm HOSE CONNECTION
L. PRESSURE RELEASE VALVE
M. GRAB HANDLE
N. PLUNGER
O. TANK OPENING
P. INLET VALVE CONNECTOR

Your EzySpray® is not suitable for drinking under any circumstance

SPRAY WAND ASSEMBLY

a. Screw the SPRAY HEAD (A) onto the WAND THREAD (F)
b. Loosen (do not remove) the LOCKING NUT (G) on the TRIGGER (C)
c. Insert the opposite end of the WAND (B) through the locking nut on the TRIGGER
d. Tighten the locking nut on the TRIGGER
e. This completes the assembly of the SPRAY WAND

SPRAY HOSE CONNECTION

a. Remove the protective end cap from the TANK OUTLET (H)
b. Screw one end of the HOSE (D) onto the TANK OUTLET (H)
c. Screw the other end of the HOSE onto the threaded end of the SPRAY WAND assembly
For the easiest assembly, be sure to screw the hose onto the tank outlet before screwing onto the spray wand

TANK PRESSURE CHECK

Before filling your EzySpray® , be sure to check the pressure gauge
a. Locate the PRESSURE GAUGE (I) on the side of the PRESSURE TANK (E)
b. Check the pressure gauge reads at least 1 BAR
This is required for the pressurised tank to work correctly
c. If pressure is satisfactory, proceed to Steps 4 and 5
d. If the pressure gauge is low, follow the Re‑pressurise process in Troubleshooting

HOLMAN 5L EzySpray Free Garden Sprayer - TANK PRESSURE CHECK
1

HOLMAN 5L EzySpray Free Garden Sprayer - overview 1

https://www.holmanindustries.com.au/product/ezyspray-5l-pump-free-garden- sprayer/

Scan me with your phone for more resources!

PATENTS
Australia: 2007209766
New Zealand: 569888
United Kingdom: GB2449588
Canada: 2,640,600
Made under license from Pressuresac Pty Ltd, Kinglake Australia.

Need help? Visit www.holmanindustries.com.au/5l- ezyspray/ for more product information or support.holmanindustries.com.au/ for additional help

Spray Additives

Removing the Grab Handle
a. Push down on the GRAB HANDLE (M)
b. Twist counter‑clockwise to unhook the GRAB HANDLE from the PRESSURE TANK (E)
c. Pull the GRAB HANDLE out of the PRESSURE TANK
d. Place the GRAB HANDLE somewhere clean to avoid dirt touching the lubricated PLUNGER (N)
e. Add fertiliser or other additives to your EzySpray® before filling with water
f. Optional: To include more additive, insert the plunger to push the first shot into the tank
g. Optional: For powder additives, include a cup of water in addition to the additive
h. Repeat Steps 4c and d as necessary to introduce more additive

Introducing Spray Additives
  Ensure the SPRAY HOSE (D) is attached when removing or replacing the GRAB HANDLE to avoid excess additive or water squirting out of the PRESSURE TANK outlet
i. After removing the GRAB HANDLE, follow your additive instructions to pour the correct amount into the TANK OPENING (O)

HOLMAN 5L EzySpray Free Garden Sprayer - Spray Additives
2

j. Insert the PLUNGER into the TANK OPENING, in the position shown above, push down and rotate clockwise to hook the GRAB HANDLE back into place
k. Follow Tank Filling in Step 5 to fill the tank with water and mix in the additive

Tank Filling

Tank Filling
Min. tap pressure required to fill tank: 350kPa

HOLMAN 5L EzySpray Free Garden Sprayer - Tank Filling
1

a. Before filling your EzySpray®, push excess air from your garden hose by turning on the tap
This will stop additional air using the EzySpray® capacity
b. Once water is flowing out, you can turn off the tap
c. Locate the 12mm snap‑on HOSE CONNECTION (K)
d. Attach the INLET VALVE CONNECTOR (P)
e. Add a standard 12mm garden hose (Q) onto this connection
f. Ensure the INLET VALVE (P) is open and turn the garden hose tap on begin filling

Watch the pressure gauge as the reservoir fills with water
The gauge should begin moving towards MAX level
g. If your water source is high pressure, it may trigger the PRESSURE RELEASE VALVE (L) when full to stop your EzySpray® from over‑pressurising:

h. If your water source is low pressure, the EzySpray® will stop filling when it reaches the maximum pressure
i. Once your EzySpray® is full, turn off your tap and close the INLET VALVE (P)
j. Disconnect the INLET VALVE (P) and garden hose
High or low pressure circumstances are fine and shouldn’t damage your EzySpray®
Watch for excess water from the hose when disconnecting

HOLMAN 5L EzySpray Free Garden Sprayer - Tank Filling
2

Don’t leave unattended while filling!

Spraying

Spray Functions
The SPRAY HEAD (A) includes 4 individual spray functions: JET, CONE, SHOWER and MIST
a. Before spraying, twist the orange section of the SPRAY HEAD to select the desired spray pattern

HOLMAN 5L EzySpray Free Garden Sprayer - Spraying 1

Trigger Action
b. To begin spraying, simply point the SPRAY HEAD in the desired direction and pull the orange TRIGGER (C) lever

Flushing and Cleaning

Spray Functions
It is important to completely flush your EzySpray® with clean water when finished with chemical spraying
a. After you have completed your spraying job and the tank has run out, connect to a tap and refill the tank with clean water
b. Point your spray wand into a bucket or anywhere you don’t mind the excess fluid flowing
c. Hold down the trigger and let the contents flow through until the tank is empty
d. Once the tank is empty, we recommend storing your EzySpray® in a dry, protected space out of direct sunlight

Don’t leave full for extended periods of time!

Troubleshooting

Question Answer

Why won’t my EzySpray ® work?
Why is the pressure gauge reading below 1 bar?
HOLMAN 5L EzySpray Free Garden Sprayer - Troubleshooting
1| Your EzySpray® may need to be re‑pressurised:
This is only necessary if the pressure is below 1 bar. It should be able to hold this minimum pressure for an extended period
a. Locate SCHRADER (bike) VALVE (J) on the opposite side to the GAUGE (I)
b. Unscrew the lid off the valve
c. Attach a standard bike pump
d. Pump air in until the gauge reads at least 1 bar
Check the PRESSURE GAUGE (I) to ensure water is in the tank
Check hose for kinks and blockages
Check wand for blockages
Try each setting on the spray head and check this for blockages
Why is the pressure release valve triggered and spraying water during filling?| This is perfectly normal and means the tank is full of water
Turn off your tap and disconnect your garden hose
Why is my EzySpray ® hose difficult to screw onto the tank and wand?| The hose included with your EzySpray® is designed for the best seal possible, which
may be difficult to screw on during initial assembly
For the easiest assembly, screw the hose onto the tank outlet before screwing onto the spray wand
Why has the pressure gauge stopped rising while filling with water?| The EzySpray ® can still be used when not entirely full
It may be due to a low‑pressure water source–try filling the tank elsewhere with higher water pressure
Why doesn’t my garden hose fit on my EzySpray®?| Your hose may be 18mm
Unscrew the 12mm hose connection and replace with an 18mm version
Visit www.holmanindustries.com.au/product/18mm‑brass‑sprinkler‑adaptor for more info
How do I empty my EzySpray®?| Point your spray wand anywhere you don’t mind the excess fluid flowing
Hold the trigger and let the contents spray until the tank is empty

HOLMAN 5L EzySpray Free Garden Sprayer - overview 2

We really appreciate having you as a customer, and would like to say thank you for choosing us.
We recommend registering your new product on our website. This will ensure we have a copy of your purchase and will activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter.

HOLMAN 5L EzySpray Free Garden Sprayer - qr 1www.holmanindustries.com.au/product- registration/ For the #SMARTGARDENER
Head Office/Service
11 Walters Drive, Osborne Park WA 6017
Tel: +61 8 9416 9999 Fax: +61 8 9416 9920
support@holmanindustries.com.au
www.holmanindustries.com.au
Copyright © 2023 Holman Industries

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals