ORIGIN 21 WLL109BK Keaston 11 in Black Integrated Outdoor Wall Light Instruction Manual
- May 15, 2024
- Origin 21
Table of Contents
ORIGIN 21 WLL109BK Keaston 11 in Black Integrated Outdoor Wall Light
ORIGIN 21 and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Questions, problems or missing parts?
Before returning contact us on:
888-251-1026, 8 a.m. – 8 p.m., EST,
Monday – Sunday or ascs@lowes.com
Thank you for purchasing this ORIGIN 21 product. We’ve created these easy-to-
follow instructions to ensure you spend your time enjoying the product instead
of putting it together. But, if you need more information than what is
provided here, please visit Lowes.com, search the item
number and refer to the Guides & Documents tab on the product’s page.
Note : You must refer to the full manual online for the complete safety
information, care instructions, troubleshooting and warranty.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electrical shock, fire or other injuries that could be fatal./Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. No hacerlo podría provocar descargas eléctricas, incendios u otras lesiones, las que pueden ser fatales.
DANGER
- DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an electrical system not having a proper grounding means could cause serious injury or death.
- If using this light fixture in a WET location, this light fixture must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock or death.
- DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the black or white house wires could cause serious injury or death./NO conecte el conductor de puesta a tierra de aislamiento desnudo o verde de la lámpara al conductor negro (DE CORRIENTE) que lleva la corriente o al conductor blanco (NEUTRO) de la casa. Conectar el conductor de tierra desnudo o verde de la lámpara al conductor negro o blanco interior podría provocar lesiones graves o la muerte.
- DO NOT damage or cut the wire insulation (covering) during installation of fixture. DO NOT permit wires to contact any surface having a sharp edge. To do so may could cause serious injury or death./NO dañe ni corte el aislamiento del conductor (cubierta) durante la instalación de la lámpara. NO permita que los conductores entren en contacto con superficies que tengan un borde afilado, ya que esto podría provocar lesiones graves o la muerte.
WARNING
- THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
- To avoid personal injury, gloves may be necessary while handling fixture parts with sharp edges./Para evitar lesiones personales, puede ser necesario usar guantes al manipular las piezas de la lámpara con bordes filosos.
- All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire – most dwellings built before 1985 have supply wire rated for 140 °F. Consult a qualified electrician before installation.
CAUTION
-
TURN OFF ELECTRICITY at circuit breaker box before beginning installation by switching the circuit breaker off.
-
If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
-
All fixtures must be mounted to an outlet box that is supported by the building structure.
-
If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
-
Before installation is complete, carefully check all screws, bolts and nuts on fixture to ensure that they are secure.
-
Note: The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; (2) this device must accept any interference received, including interference that may cause undesired operation.
Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75050; 800-527-1292 -
Total wattage for this fixture is 10 watts; do NOT tamper with or attempt to repair LED component of fixture.
FEELING CONFIDENT? START YOUR NEXT PROJECT
Visit Lowes.com for more information.
WARNING
- DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting plate which is first attached to the outlet box. Suspending a fixture by the house wires and wire connectors could result in the fixture falling, with the possibility of personal injury, electrical shock or fire.
- To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with each light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician.
- To reduce the risk of damage to the fixture, DO NOT use power tools to assemble any part of the fixture.
- Failure to caulk fixture mounting surfaces with silicone weather sealant may result in water damage in outlet box, which may cause electrical malfunction or electrical shock.
- To avoid water damage to fixture or possible electrical malfunction, install fixture at least 4 ft. above the ground/floor.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 30 minutes
TOOLS REQUIRED (NOT INCLUDED)
PACKAGE CONTENTS
INSTALLATION OVERVIEW
Connect wiring using preassembled lever wire connectors: WHITE to WHITE, BLACK
to BLACK, BARE/GREEN to BARE.
Consult an electrician if wiring needs differ.
Make sure no bare wire or wire strands are visible after making connections.
Before tightening C completely, use level to check A — adjust if necessary.
D is heavy. Make sure D is completely secure.
Use preassembled switch on A to choose color temperature:
- soft white
- warm white
- cool white
- daylight
- cool daylight
Caulk mounting surface of A with silicone weather sealant (not inlcuded).
Failure to caulk may result in water damage in outlet box, which may cause
electrical malfunction or electrical shock.
Turn on power source
Documents / Resources
|
ORIGIN 21 WLL109BK Keaston 11 in Black Integrated Outdoor Wall
Light
[pdf] Instruction Manual
WLL109BK Keaston 11 in Black Integrated Outdoor Wall Light, WLL109BK, Keaston
11 in Black Integrated Outdoor Wall Light, Integrated Outdoor Wall Light,
Outdoor Wall Light, Wall Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>