havit HV1832W-12V Klip Stainless Steel LED Inground Light Instruction Manual

Table of Contents

Klip Inground Light Installation Instructions
Instruction Manual

havit HV1832W 12V Klip Stainless Steel LED Inground Light
-

Model No.	HV1832W-12V	HV1832C-12V	HV1832W-240V	HV1832C-240V
Name	Klip
Material	316 Stainless Steel cover + Aluminium body
Colour	Cover – Stainless Steel I Body – Black
IP Rating	IP67
Input Voltage	12v DC	240V
Protection Class	(Low Voltage)	(Requires Earth)
Lamp Base	Built-In LED
Lamp Wattage	1x 10w	1x 10w
Colour Temp	3000k	5500k	3000k	5500k
Lumens	8001m	9001m	8001m	9001m
CRI	> 80
Wiring	Parallel
Dimmable	No

havit HV1832W 12V Klip Stainless Steel LED Inground Light -
1

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, the Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
All o-rings and seals must be in place correctly to maintain the warranty
When installing inground light fittings, Adequate drainage must be allowed to prevent fittings from sitting in water for a long period of time, if no drainage is allowed, the Warranty will be voided, See sample adequate drainage diagram for correct installation method.
This form may be updated at any time due to product improvements, please check the online installation form for the most current version.

HV1832-240V

Make sure that the electrical circuit is free of voltage (master switch off)
Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
To connect the cable, strip back cable on both fitting and cable run and twist the earth together first, then positive cables from fitting to positive on the cable run.
Then connect neutral cables from fitting to neutral on cable run.
Solder all joins using solder and either a heat gun or butane gas torch.
Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
Heat the heat shrink or crimp the gel cap making sure all connections are covered.
Make sure the seals are still in place and screws are tight to avoid any water penetration.
Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

HV1832-12V

Make sure that the electrical circuit is free of voltage (master switch off)
Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
Solder all joins using solder and either a heat gun or butane gas torch.
Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
Heat the heat shrink or crimp the gel cap making sure all connections are covered.
Make sure the seals are still in place and screws are tight to avoid any water penetration.
Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.