iBEAM TE-7VS Dash Mount Monitor Heavy Duty Camera User Manual

: August 21, 2024
: iBEAM

Table of Contents

iBEAM TE-7VS Dash Mount Monitor Heavy Duty Camera
Product Usage Instructions
Remote control
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iBEAM TE-7VS Dash Mount Monitor Heavy Duty Camera

Specifications

Screen Size: 7-Inch TFT LCD Monitor
Resolution: 800 x 480 Pixels
Aspect Ratio: 16:9
System: NTSC / PAL
Power Supply: DC 12V
Power Consumption: 7.8W
Working Temp: – 10℃~ + 60℃
Storage Temp: 20℃ ~ +70℃
Video: Two video inputs (V1 / V2)
Rear view : Standard and mirrored
Operation Mode: Full function OSD and remote control

Product Usage Instructions

Front Panel Controls

V1 / V2 Switch
Image direction switch (left/right/up/down)
Menu
Decrease (-)
Increase (+)
Power on/off
Wireless signal receiver

Remote Control Functions

Power on/off
Video select
FOV (Field of View)
Decrease (-)
PEF (Preferred Field of View)
Increase (+)
Menu
Mode Select

Connection Diagram
White: V1 Input, Yellow: V2 Input (The camera will switch to V2 automatically once reversing)

Warning
Do not watch the monitor while the vehicle is in motion, as it is hazardous.

Important Information
If you encounter difficulties with the installation, contact Tech Support at 1-800-253-TECH. Ensure the installation follows the instructions precisely before seeking assistance.

Safety Instructions
When connecting the power cable, ensure correct polarity to prevent fuse blowout. Replace blown fuses with the same specification and never increase the current rating or use metal wire as a substitute.

Enhance Your Skills
Visit www.installerinstitute.com or call 800-354-6782 for information on improving your installation and fabrication skills.

Certification Recommendation
Metra recommends MECP certified technicians for installations.

Version Information
Version: 1.0

Frequently Asked Questions (FAQ)

Q: Can I use this product with a different power supply?
A: No, this product is designed for use with a DC 12V power supply only. Using a different power supply may damage the device.
Q: How do I switch between V1 and V2 inputs?
A: Use the V1 / V2 switch on the front panel or the corresponding function on the remote control to switch between inputs.

iBeamUSA.com
MetraDealer.com
techsupport@metra-autosound.com
TECH SUPPORT
800-253-8324

Front Panel

V1 / V2 Switch
Image direction switch (left/right/up/down)
Menu
Decrease (-)
Increase (+)
Power on/oﬀ
Remote signal receiver window

Remote control

Power on/oﬀ
Video select
Decrease (-)
Increase (+)
Menu
Mode Select

Diagram

Warning
Do not watch monitor while vehicle is in motion, as it is hazardous

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Attention
When connecting with power cable, please make sure not to mistake the positive and negative pole, otherwise the fuse will blow immediately for security protection. If it happens, please replace the blown fuse with a new one with same specification, after connecting properly to the right pole. Don’t randomly increase the current rating of the fuse, and NEVER use metal wire as a substitute.