ZUMTOBEL LM-XPO Replacement Kit Instruction Manual
- May 15, 2024
- ZUMTOBEL
Table of Contents
LM-xPx Replacement Kit
LM-xPx Replacement Kit (22 171 589)
Application area
The device may only be used for the applications specified.
Safety instructions
- Installation of this device may only be carried out by specialist staff who have provided proof of their skills.
- The power supply must be switched off before handling the device.
- Installation/removal only when isolated from power supply.
- Connecting terminal may only be attached/removed when isolated from the power supply.
- The relevant safety and accident prevention regulations must be observed.
- Do not remove protective devices.
- Specialist personnel must ensure that the device is permanently connected to an earth conductor.
Technical data
Nominal voltage | 230 V, 50 Hz |
---|---|
Permissible input voltage | 220-240 V, 50-60 Hz |
Power dissipation | Max. 34 VA |
Interface | LM-Bus (B1, B2) |
Bus loads | 2 bus loads |
Terminals | Mains (L, N, PE): 0.75-2.5 mm2 (solid) or 0.5-1.5 mm2 (fine- |
stranded with core end ferrule) LM-Bus: 0.5-1.5 mm2 (solid or fine-stranded)
Degree of protection| IP20
Protection class| Protection class I
Housing material| Front frame: aluminium, painted black Display: glass
Installation| For installation in MKXP installation box (art. no. 22 154 482)
Dimensions| Total: 200 x 155 x 82 (W x H x D, in mm) On wall: 200 x 155 x 9
(VV x H x D, in mm)
Permissible ambient temperature| 0-40°C
Permissible relative humidity| 20-90%, non-condensing
Weight| Approx. 1.9 kg (complete set)
INSTALLATION
Devices that can be replaced:
LM-XPO (art. no. 22 154 405)
LM-CPO (art. no. 22 154 195)
LM-MPO (art. no. 22 154 196)
LM-CPA (art. no. 22 146 153)
LM-MPA (art. no. 22 146 166)
Removing the old touch panel (A):
- Carefully pull out the touch panel at the top edge against the spring.
Removing the old touch panel (B):
Pull out the mains (230 V AC) and LM-Bus plug-in terminals.
Installation box for the touch panel:
MKXP (art. no. 22 154 482)
Note: the installation box is intended for further use and must not be
removed.
Removing the old touch panel (C):
Loosen the two screws.
Remove the LM-xPx bracket.
Removing the old touch panel (D):
Remove the LM-xPx plug-in terminals.
Remove the core end ferrules from the LM-Bus conductors, if necessary.
Installing the new touch panel (A):
Scope of delivery:
– Touch panel including bracket set.
Installing the new touch panel (B):
- Connect the mains lines to the terminal block of the bracket set. Follow the correct designations on the terminal block (L, N, PE).
- Connect the LM-Bus to the terminals after the ferrite ring.
- Re-attach the contact safety guard (plastic clip).
plastic clip
Installing the new touch panel (C):
Secure the bracket set to the MKXP.
Installing the new touch panel (D):
Connect the earthing cable of the touch panel to the bracket set.
Installing the new touch panel (E):
Connect the LM-SI03D-USB to the touch panel using the USB connection cable
supplied.
Connect the supply plug (red–black line) to the touch panel.
Installing the new touch panel (F):
Mount the touch panel to the front and press lightly until the touch panel
clicks into place.
Note: the touch panel can be loosened from the bracket without tools by
pulling on the frame.
Zumtobel Lighting GmbH
Schweizerstraße 30
6850 Dornbirn AUSTRIA
www.zumtobel.com