marklin 39867 Class 189 Electric Locomotive Rotterdam RF Instruction Manual
- June 17, 2024
- marklin
Table of Contents
marklin 39867 Class 189 Electric Locomotive Rotterdam RF
Product Information
Specifications
- Model: BR 189 Electric Locomotive
- Product Number: 39867
- Digital Protocols: mfx, DCC, MM
- Software Version Requirement for F16 and F17 Functions: 3.55 in MS2
FAQ
- Q: How can I deactivate individual digital protocols?
- A: Individual protocols can be deactivated with Parameter CV 50.
- Q: When can I access functions starting at F16?
- A: Functions starting at F16 are accessible after updating to Software Version 3.55 in the MS2.
Safety Information
Safety Notes
- This locomotive is to be used only with an operating system designed for it (Märklin AC, Märklin Delta, Märklin Digital or DCC).
- Use only switched mode power supply units and transformers that are designed for your local power system.
- This locomotive must never be supplied with power from more than one transformer.
- Pay close attention to the safety notes in the instructions for your operating system.
- The feeder track must be equipped to prevent interference with radio and television reception, when the locomotive is to be run in conventional operation. The 74046 interference suppression set is to be used for this purpose.
- Do not expose the model to direct sunlight, extreme changes in temperature, or high humidity.
- WARNING: Sharp edges and points required for operation.
- The LEDs in this item correspond to Laser Class 1 according to Standard EN 60825-1.
Important Notes
- The operating instructions and the packaging are a component part of the product and must therefore be kept as well as transferred along with the product to others.
- Please see your authorized Märklin dealer for repairs or spare parts.
- The warranty card included with this product specifies the warranty conditions.
- Disposing: www.maerklin.com/en/imprint.html
Functions
- Recognition of the mode of operation: automatic.
- Mfx technology for the Mobile Station / Central Station.
- Name set at the factory: 189 091-2 RRF
- Address set at the factory: MM 18 / DCC 03
- Setting the locomotive parameters (address, acceleration/braking delay, maximum speed): with the Control Unit, Mobile Station, Central Station.
- Headlights, changing over with the direction of travel.
- Various controllable functions.
- Mode of Operation: Locomotive Engineer
- Additional explanations about the mode of operation can be found in the supplemental instructions (included).
- Only the train control functions and headlight changeover feature are available in analog operation.
Note: The digital protocol with the most possibilities is the highest order digital protocol. The sequence of digital protocols in descending order is:
- Priority 1: mfx
- Priority 2: DCC
- Priority 3: MM
If two or more digital protocols are recognized in the track, the decoder automatically takes on the highest value digital protocol.For example, if mfx & MM are recognized, the mfx digital protocol is taken on by the decoder. Individual protocols can be deactivated with Parameter CV 50.
Controllable Functions
- The number corresponds to the button number on the device.
- Functions starting at F16 are not possible until you have Software Version 3.55 in the MS2.
- with random sounds
- only in conjunction with Headlights/marker lights / switched together: „Double A“ switching lights
- Only for „World of Operation“, do not move (do not map).
Parameter
CV (Parameter) | CV-Nr. | Value |
---|---|---|
Address | 01 | 01 – (80)* 255 |
Acceleration delay | 03 | 01 – (63)* 255 |
Braking delay | 04 | 01 – (63)* 255 |
Maximum speed | 05 | 01 – (63)* 255 |
Reset to series value | 08 | 08 |
Alternative Protocols | 50 | 0 – 15 |
Volume | 63 | 01 – (63)* 255 |
CV 50 Alternative Protocols
Installation And Care Instructions
Parts
- Antenna, signal horns / E380 106
- pantographs / E352 747
- pantographs —
- pantographs / E116 071
- carrier insulation / E116 065
- handle bars / E380 107
- screw / E750 250
- screw / E786 750
- decoders / 373 744
- speakers / E101 066
- PCB lighting / E236 095
- buffer beam / E204 016
- buffer / E203 618
- Kicks / E112 817
- hooks / E282 390
- snow clearers / E212 704
- Coupling drawbar / E204 015
- Shift slide spring / 7 194
- Close coupling / E357 874
- retaining clip / E230 561
- Shaft, bearings, joints / E259 277
- Shaft, bearings, joints / E259 278
- Engine / E192 730
- screw / E785 200
- driving frame / E195 612
- driving frame / E195 611
- traction tires / 7 153
- screw / E786 790
- grinder / E206 370
- Details of the representation can from that Model differ.
Note
- Several parts are offered unpainted or in another color.
- Parts that are not listed here can only be repaired by the Märklin repair service department.
General Note to Avoid Electromagnetic Interference:
- A permanent, flawless wheel-rail contact is required in order to guarantee operation for which a model is designed.
- Do not make any changes to current-conducting parts.
The close coupling from 72000 (E357874) is mounted on this locomotive.
We recommend to also mount the close coupling from 72000 on the wagons to be
coupled.
Contact
Gebr. Märklin & Cie. GmbH
- Stuttgarter Str. 55 – 57
- 73033 Göppingen Germany
- www.maerklin.com
- www.maerklin.com/en/imprint.html
Subject to change
© Gebr. Märklin & Cie. GmbH
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>