db Technologies IS210T Loudspeaker Instruction Manual

June 17, 2024
dB Technologies

db Technologies IS210T Loudspeaker

db-Technologies-IS210T-Loudspeaker-PRODUCT

MAIN FEATURES

  • Impressive sound pressure
  • Rotatable horn
  • Quick installation
  • Easy handling and transport
  • Stack or flyable use

PACKAGE CONTENTS

The box contains:
N°1 IS210T loudspeaker
This quick start and warranty documentation

DESCRIPTION

IS210T is the new dB Technologies 2-way passive speaker for professional use. It is equipped with a compression driver (HF exit: 1.4”, 2.4 voice coil) and two 10” neodymium woofers (2.4” voice coil). The coverage pattern is 90° (H) x 40° (V).
The horn is rotatable and the mechanical design allows an easy, accurate, and quick installation for stand or flyable use thanks to the optional brackets.

ACCESSORIES

db-Technologies-IS210T-Loudspeaker-FIG-
\(2\)

DIMENSIONS

db-Technologies-IS210T-Loudspeaker-FIG-
\(1\)

TECHNICAL SPECIFICATIONS

Speaker Type 2 Way Passive Loudspeaker
Protection against solid objects and liquids (IP): 55
Frequency Response [-6dB] 60 Hz – 17.8 kHz
Usable Bandwith [-10dB] 56 Hz – 20 kHz
RMS power 400 W
Rated impedance 8 Ohm
Max SPL (1 m) 133 dB (full range)
Directivity (HxV) 90° x 40°
HF 1.4” exit, 2.4” v.c.
LF 2x 10”, 2.4” v.c.
Crossover Frequency 840 Hz
Signal Input Terminal barrier strip (or speakON® using the SP-IS accessory

panel)
Signal Output| Terminal barrier strip (or speakON® using the SP-IS accessory panel)
Housing| Wooden box – black finished
Rigging Points| 4
Dimensions (WxHxD)| 300x780x430 mm (11.8×30.7×16.9 in)
Weight| 28.7 Kg (63.3 lbs.)

CONNECTIONS

db-Technologies-IS210T-Loudspeaker-FIG-
\(3\)

PROTECTION AGAINST SOLID OBJECTS AND LIQUIDS (IP RATING)
The speakers are protected against the ingress of solid objects and liquids with a rating of IP55 as defined by IEC 60529. Please only use cables with the specified diameters:

  • PG9 => between 4 and 8mm diameter
  • Fasten properly the cable gland using the plastic tightening nut.

WARNING!
Failure to comply with these installation prescriptions could adversely affect the declared protection ratings

MECHANICAL FIXING POINT
Is 210T can be installed in different configurations. For a quick installation, on each side of the loudspeaker, the user can find mechanical fixing points for stand and flyable use (A).

CONFIGURATIONSdb-Technologies-IS210T-Loudspeaker-FIG-
\(5\)

WARNINGS

  • WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
  • For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check all the components for damages, deformations, and missing or damaged parts that may compromise safety during installation.
  • If you use the loudspeakers outdoors avoid spots exposed to bad weather conditions.
  • The external wiring connected to speaker output terminals requires installation by qualified personnel only. Once the equipment is installed, prevent access to the connectors to unqualified personnel. Only use the accessories and configurations described in this manual, and proceed by the instructions given in the manuals for the accessories. dBTechnologies will not accept any responsibility for damages caused by inappropriate accessories or additional devices.
  • Installation and use of this equipment and its accessories must be performed only by “Expert personnel” according to safety standards. To prevent hazards to people, animals, and/or objects, make sure that the installation is stable and secure. Comply with the safety regulations and laws in force in the country in which you use the product. For safe use, periodically check that all parts are in good working condition before use. Only authorized personnel may carry out the design, calculations, installation, testing and maintenance of professionally flown or stacked audio systems.
  • Check periodically the integrity and the functionality of the accessories and the technical equipment for a safe installation. Users should never apply a load that exceeds the working load limits of any rigging components or equipment here presented. design, calculation, installation, testing, and maintenance of suspension and stack systems for audio equipment must be performed only by qualified and authorized personnel. AEB Industriale s.r.l. denies any responsibility for improper installations, in the absence of safety requirements. Features, specifications, and appearance of products are subject to change without notice.
  • dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously manufactured.

Scan with your QR Reader App to download the complete User Manual.db-
Technologies-IS210T-Loudspeaker-FIG- \(6\)

A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
Tel. +39 051 969870
Fax +39 051 969725
www.dbtechnologies.com
info@dbtechnologies-aeb.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

dB Technologies User Manuals

Related Manuals