db Technologies VIO S218F Active Bass-Reflex Subwoofer User Guide
- June 11, 2024
- dB Technologies
Table of Contents
- MAIN FEATURES
- PACKAGE CONTENTS
- DESCRIPTION
- ACCESSORIES
- DIMENSIONS
- TECHNICAL SPECIFICATIONS
- Setup, turn on and I/O settings
- POWER SUPPLY SPECIFICATIONS (POWER ABSORPTION)
- MECHANICAL FIXING POINT
- **INSTALLATION
- CONFIGURATIONS
- STACKED CONFIGURATIONS
- IMPORTANT NOTES AND WARNINGS
- IMPORTANT SAFETY INSTRUCIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VIO S218F Active Bass-Reflex Subwoofer
User Guide VIO S218F
QUICK START USER MANUAL SECTION 1
420120416Q REV1.0
MAIN FEATURES
- Impressive sound pressure
- Powerful amplifier
- Quick installation
- Flyable use
- AURORA Net control
PACKAGE CONTENTS
The box contains:
N°1 VIO S218F subwoofer
N°1 mains cable
N°2 fuses for 100-120Vac power supply
N°2 snap pins
This quick start and warranty documentation
DESCRIPTION
VIO S218F is a flyable active bassreflex-horn subwoofer, designed for professional use, equipped with two 18” neodymium woofer (voice coil: 4”). The powerful DSP controlled double DIGIPRO® G4 amplifier section can handle up to 3200 W (RMS power). The RDnet connections allow in-depth remote control, thanks also to free available software (AURORA NET, dBTechnologies Composer). The custom flybar ensure easy set-up to create different configurations, completing live installations with VIO linearray series.
ACCESSORIES
DRK-218F Flybar for flyable use| DRK-212 flybar for stacked use with VIO-L212
speakser
DO-VIOS218F dolly for transport| DRK-210 flybar for stacked use with VIO-L210
speakers
DIMENSIONS
TECHNICAL SPECIFICATIONS
Speaker Type | Active bass-reflex subwoofer |
---|---|
Frequency Response (-6d8( | 28 Hz – Cut frequency (crossover dependent) |
Usable Bandwith (-10dB) | 27 Hz – Cut frequency (crossover dependent) |
Max SPL (1 m) | 143 dB |
LF | 2x 18″, 4″ v.c. neo |
Crossover Frequency | 6o to no Hz + full-range |
Amplifier | Digipro• Gd 3200 (2xi600) W RMS Class-D |
Power Supply | Full.range SMPS |
Cooling | Passive (convection) and internal fan |
Operating Range | 100-24W’ (5040Hz) |
Limiter | Peak, RMS, Thermal |
Operation limit temperature | -20°C / +55°C (-4°F / 131°F) |
Controller | 32 bit DSP |
AD/DA Converter | 24 bit/96 kHz |
Preset | Cardioid |
Controls | 1)( Delay control rotary |
lx Link/Xover button
lx Cardioid preset button
lx System test button
lx Polarity button
1)( Subwoofer attenuation rotary 1% Xover rotary
Signal Input| 1 x XLR balanced, 1 x R145 (RDNet), ix USB (Data Service)
Signal Output| ix XLR balanced Link, ix XLR HPF Xover out,
1 x R145 Link (RDNet)
Housing| Wooden box – black finished
Rigging Points| 2
Dimensions (WxHxD)| 1300%520%800 RIM (51.18×20.47×31.50 in)
Weight| 100 Kg (no Lbs.)
I/O and Control panel
The DigiPro G4
amplifier of VIO S218F is controlled by a powerful DSP. All the connections
and controls are in the rear amplifier control panel.
- Balanced audio input and output link
- Polarity switch
- Delay rotary control
- Cardioid preset switch
- Status LEDs (Limiter, Signal, Mute/Protection, Ready)
- Subwoofer attenuation rotary control
- System Test button
- Mini B-type USB port for firmware update
- RDNet Data In / Data Out and Control LEDs
- HPF Xover (balanced) output
- Xover rotary control
- Full-range Mains input
- Mains Link output
- Mains Fuse
Setup, turn on and I/O settings
Connect first the audio input (1); if you need to link the VIO S218F to
another one, please use a cable with XLR connectors (not supplied). Connect
the Link output of the first, to the balanced Input of the second one, and so
on.
Plug properly the mains POWERCON TRUE1 cable (supplied) in the related input
(12) to turn on the system.
In case of remote control, connect the Data Input of the subwoofer to the
hardware remote controller (RDNet Control 2 or RDNet Control 8) with cables
equipped with etherCON connectors; to link another subwoofer connect the Data
Output of the first, to the Data Input of the second one, and so on. Please
use a cable with etherCON connectors. When the subwoofer is active and the
RDNet network is active and it has recognized the connected device, the LED
Link is on. The “Active” LED will start flashing to indicate the presence of
data traffic; the “Remote Preset Active” signals that all the local controls
set on the amplifier panel (DSP preset) are by-passed and controlled remotely
by RDNet remote control.
See also RDNet Control 2 or RDNet Control 8 user manuals for further
information.
POWER SUPPLY SPECIFICATIONS (POWER ABSORPTION)
Draw at 1/8 of full power in average use conditions (): 3,2 A (220-240V~) – 5
A (100-120V~)
Draw at 1/3 of full power in maximum use conditions (): 6,6 A (220-240V~) –
12,3 A (100-120V~)
Power absorption with speaker turned on without signal (idle): 53 W
INSTALLER NOTES:** The values refer to 1/8 of full power, in average
operating conditions (music program with infrequent or no clipping). It is
recommended to consider them the minimum sizing values, for any type of
configuration.
- *INSTALLER NOTES: The values refer to 1/3 of full power, in heavy operating conditions (music program with frequent clipping or activation of the limiter. We recommend sizing according to these values in case of professional installations and tours
HANDLES
On each side of the subwoofer the user can find handles for easy handling (A).
MECHANICAL FIXING POINT
The mechanical fixing points (B) on the top of the subwoofer allows stacked
and flyable use.
The mechanical fixing points (C) on the top of the subwoofer allows to use VIO
S218F subwoofer for stacked configurations with DRK-210 and DRK-212 flybar.
For more details, please read the CONFIGURATIONS chapter.
**INSTALLATION
**
- Place the upper subwoofer above the lowest one as shown.
- Lift both bracket side joints of the lowest subwoofer as shown. Be sure that the side joints of the lowest subwoofer fit with the upper one brackets.
- Insert the two included snap pins in the related fixing holes as shown to fasten the subwoofers.
Repeat this procedure for each subwoofer.
CONFIGURATIONS
FLYABLE CONFIGURATION
VIO S218F can be hung using the DRK-218F custom flybar (not included). This
accessory allows flyable configuration up to 14 subwoofers.
For more information please refer to DRK-218F user manual.
FLYABLE CARDIOID CONFIGURATION
In case of a
cardioid configuration, follow the procedure on the previous page placing the
mid subwoofer facing rear.
Then activate the cardioid preset pushing the dedicated button on the amp
panel.
STACKED CONFIGURATIONS
Example of a stacked configuration with DRK-212 flybar
and VIO L212 speakers. For more information please refer to DRK-212 user
manual.
Example of a stacked configuration with DRK-210 flybar
and VIO L210 speakers. For more information please refer to DRK-210 user
manual.
IMPORTANT NOTES AND WARNINGS
EMI CLASSIFICATION
According to the standards EN 55032 and 55035 this is a Class A equipment,
designed and suitable to operate for professional use. Warning: This equipment
is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference
FCC CLASS A STATEMENT
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING Make sure that the loudspeaker is securely installed in a stable
position to avoid any injuries or damages to persons or properties. For safety
reasons do not place one loudspeaker on top of another without proper
fastening systems. Before hanging the loudspeaker check all the components for
damages, deformations, missing or damaged parts that may compromise safety
during installation. If you use the loudspeakers outdoor avoid spots exposed
to bad weather conditions. Contact dBTechnologies for accessories to be used
with the speakers. dBTechnologies will not accept any responsibility for
damages caused by inappropiate accessories or additional devices.
Features, specification and appearance of products are subject to change
without notice. dBTechnologies reserves the right to make changes or
improvements in design or manufacturing without assuming any obligation to
change or improve products previously manufactured.
IMPORTANT SAFETY INSTRUCIONS
- Read these instructions
- Keep these instructions.
- .Heed all warnings.
- .Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- **** Use only with the cart, stand tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution, when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
- No naked flame sources, such as lighted candles, should be placed on the apparatus
- Do not use the apparatus in tropical climates
WARNINGS!
Only expert personnel may use the product and its accessories! To prevent
hazards to people, animals and/or objects, make sure that the installation is
stable and secure. Comply with the safety regulations and laws in force in the
country in which you use the product. For safe use, periodically check that
all parts are in good working condition before use. Only authorised personnel
may carry out design, calculations, installation, testing and maintenance of
professional flown or stacked audio systems. AEB Industriale shall not be
liable for improper installation carried out without adequate safety measures.
Never suspend the speakers from the handles! Only use the accessories and
configurations described in this manual, and proceed in accordance with the
instructions given in the manuals for the accessories.
Do not obstruct the amplifier cooling fins at the back. In the event of
overheating, the audio volume is gradually reduced until the module is
thermally stable. The level is automatically restored on reaching the correct
operating temperature. Do not attempt to open the amplifier. In the event of
malfunction, immediately turn off the power, disconnect the unit from the
mains and contact an authorised service centre.
Only use the power cable provided. The USB SERVICE DATA connection is to be
used exclusively for updating the product’s firmware; do not connect any other
USB device to the unit to avoid the risk of damage and malfunction. Do not use
the monitor for a prolonged period with the limiter LED steadily lit or
flashing as this indicates operation under stress with excessive distortion.
Check periodically the integrity and the functionality of the accessories and
the technical equipments for a safe installation. user should never apply a
load that exceeds the working load limits of any rigging components or
equipment here presented. design, calculation, installation, testing and
maintanance of suspension and stack systems for audio equipment must be
performed only by qualified and authorized personnel. AEB Industriale s.r.l.
denies any and all responsibility for improper installations, in the absence
of safety requirements.
info@dbtechnologies-aeb.com
VIO S218F NOTES
QUICK START USER MANUAL SECTION 1
420120416Q REV1.0
Scan with your QR Reader App to download the complete User Manual.
https://www.dbtechnologies.com/qrcode/001102/ A.E.B. Industriale
Srl
Via Brodolini, 8
Località Crespellano 40053 VALSAMOGGIA
BOLOGNA (ITALIA)
Tel. +39 051 969870
Fax +39 051 969725
www.dbtechnologies.com
info@dbtechnologies-aeb.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>