Jump ID-1201 Suspended Fixtures LED Alite

System Overview

These instructions review how to install Jump suspended fixtures. Jump 4ft and 8ft modules can be installed as individual standalone units, or they can be joined together to create continuous runs. The graphic below shows the components required to install a typical run of Jump suspended fixtures.

IMPORTANT: Read all instructions including fixture/sensor wiring AND mechanical details before beginning installation

**Jump joint kit(s)***

• A/C mounting bracket (x1)
• Break apart joiner aligner (x1)

• 8-32 x 1/2″ screw (x2)

• 8-32 Hex Nut(x2)

• Gasket (x1)
• Power Plate (x2)
• ©Plug 1/2(x2)
  

*NOTE: 1 1 kit required for each in-run joint.

**Jump end kit(s)***

• Endcap (x1) (luminous shown)
• A/C mounting bracket (x1)

• 8-32 x 1/2″ screw TC (x2)

• Gasket (x1)
• Power Plate (x1)
• Plug 1/2(x1)

*NOTE: 2 kits required for each run (one for each end).

TOOLS REQUIRED: Phillips screwdriver, 3/8” nut driver.

Module Lengths

Jump suspended systems come in 4ft and 8ft modules. Overall module lengths are shown below.
Module lengths do not include end caps.

Endcaps

Add two end caps to the length of each run.

Mount Spacing

For on-grid T-bar ceiling installations, mounts attach directly to T-Bar. For non-accessible ceilings and off-grid T-bar installations, the graphic below indicates mount spacing for typical run lengths.

Run Configurations

The tables below indicate how 4ft and 8ft modules can be combined to create continuous runs of various lengths.

Nominal Row Length| Number of Modules Required| Installed Row Length (not including end caps)
---|---|---
| 4′| 8′|
4′| 1x| | 4′ – 3/16
8′| | 1x| 8′ – 3/8″
12′| 1x| 1x| 12′ -9/16″
16′| | 2x| 16′ – 3/4
20′| 1x| 2x| 20 – 15/16
24′| | 3x| 24 1 – 1/16
28′| 1x| 3x| 28 1 – 1/4
32′| | 4x| 32 1 – 7/16
36′| 1x| 4x| 36 1 – 5/8
40′| | 5x| 40 1 – 13/16
44′| 1x| 5x| 44 1
48′| | 6x| 48 2 – 3/16
Nominal Row Length| Number of Modules Required| Installed Row Length (not including end caps)
---|---|---
| 4′| 8′|
56′| | 7x| 56 2 – 9/16
60′| 1x| 7x| 60 2 – 11/16
64′| | 8x| 64 2 – 7/8
68′| 1x| 8x| 68 3 – 1/16
72′| | 9x| 72 3 – 1/4
76′| 1x| 9x| 76 3 – 7/16
80′| | 10x| 80 3 – 5/8
84′| 1x| 10x| 84 3 – 13/16
88′| | 11x| 88 3
92′| 1x| 11x| 92 4 – 3/16
96′| | 12x| 96 4 – 3/8
100′| 1x| 12x| 100 4 – 1/2

*Overall run lengths provided do not include end caps. Add two endcaps to the overall length of each run.

Prepare Fixtures / Install ceiling mounting components

Arrange boxed fixtures on floor in specified mounting locations; remove fixtures from boxes. Install all ceiling mounting components and vertical aircraft cables using separate installation instructions for Aircraft Cable Mounting (supplied).

Assembly instruction

1. Prepare Fixtures / Install ceiling mounting components
   Arrange boxed fixtures on floor in specified mounting locations; remove fixtures from boxes. Install all ceiling mounting components and vertical aircraft cables using separate installation instructions for Aircraft Cable Mounting (supplied).

2. Slide in power cover and install bushing (power location) or plug (non-power location) on both ends.
   Install one gasket perjoint.

3. Install Aircraft Cable brackets
   Slide A/C mounting bracket into mounting channel to the mounting position, and tighten locking bracket until screw is tight. Mounting position can be up to 18″from end.
   If desired mounting location is directly over a joint, position A/C bracket and lock in a position first where all teeth engage into channel, then move into correct position after 2nd fixture is installed.

4. Suspend and Level First Fixture
   With two people, raise first fixture to ceiling. At each end of fixture, insert aircraft cable through aircraft cable adjuster (located on A/C mounting bracket). The adjuster will automatically grip and hold the cable.
   IMPORTANT: Do not force cable into adjuster. See instruction A (next page) for details. To level fixture, support fixture from below and use supplied aircraft cable release tool to make fine height adjustments.

5. Attach Clips and Tuck Wires
   POWER LOCATIONS: Attach cable clips at 4 increments between power drop and bushing in power cover. Feed power cord through bushing (shown above). Complete electrical connections using wire nuts (supplied by others). Tuck wires into wire cavity.
   NON-POWER LOCATIONS : Cap all wires and tuck into wire cavity.

6. Install Joiner Aligners
   Slide joiner aligner brackets into corresponding slots in fixture cross plate.

7. Suspend and Join Additional Fixtures to Create Row
   With two people, raise second fixture to ceiling. At end of fixture (opposite joint), insert aircraft cable through adjuster. At joint, rest fixture on in-run joiner bracket.
   IMPORTANT: Do not attempt to join fixtures on floor. Instead, hang one fixture at a time and join modules at ceiling level.

8. Complete Electrical Connections at Joints
   Complete in-run electrical connections. NON-POWER LOCATIONS (shown above): Use supplied quick-wire connectors. Tuck wires into wire cavity.
   POWER LOCATIONS: Feed power cord through bushing in bracket. Use wire nuts (supplied by others) to complete connections. Tuck wires into wire cavity.

9. Secure Joints and Level all Fixtures
   Slide modules together; secure joint from below using supplied nut and screw hardware (requires Phillips driver).
   IMPORTANT: Ledalite recommends tightening fasteners by hand. When joining modules, ensure screw is tightened snug plus an additional 1/4 turn.
   LEVEL FIXTURE: See A below. Repeat STEPS 4-7 for each additional fixture in row.

10. Install endcaps
    Snap on the gasket to the end of the fixture and attach end caps using supplied #8 screws.

11. Finishing
    Install lenses as shown.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause  harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Aircraft cable adjustment

IMPORTANT: Do not force cable into adjuster. To insert cable into adjuster, follow the steps below.

1. CUT
   If required, cut cable ends cleanly prior to inserting into adjuster. Recommended cutters: K.K. Porter cable cutter cat. No. 0690TN or Klein all purpose shears cat.
   No. 1104.

2. INSERT
   Carefully insert cable into tapered end. If cable does not insert easily or becomes jammed during insertion, use the release tool to remove cable. Trim end again and repeat process. DO NOT BEND CABLE BELOW BOTTOM OF ADJUSTER.

3. TEST
   Once cable is inserted, apply a 25lb point load to each mount bracket to ensure all connections are secure.

Level vertically

LEVEL VERTICALLY (shown above) : Support fixture from below and use supplied aircraft cable release tool to make fine height adjustments (see instruction A for details).

NOTE: Ensure fixture is level end-to-end. Support fixture from below and use supplied aircraft cable release tool to makefine height adjustments.

Sensor in Rows

Single Sensor Controlling Whole Row

1. Purple & brown (or purple & grey/pink) control wires MUST be connected between fixtures.
   Note :

   • A maximum of 8 drivers can be wired to 8 sensors; confirm fixture driver count with factory.
     
     Multiple Sensors Controlling Separates Zones in a Row

2. Purple & brown (or purple & grey/pink) control wires MUST NOT be connected between zones.
   Notes :

   • A maximum of 8 drivers can be wired to one sensor; confirm fixture driver count with factory.

   • Only one sensor is allowed on a wired zone. (Sensors can be paired together wirelessly via a mobile app).
     
     Sensor Spacing

   • For correct operation, sensor should be placed a minimum distance of 8ft apart.

   • Wireless sensor should be placed no further than 40ft apart for good wireless signal connection.
     

Important Consideration When Using Sensor in a Row

• For fixtures with wireless sensors (CS, SB or RA options):
  DO NOT connect fixture purple and brown (or purple & grey/pink) control wires to an external dimming switch.
  Fixture mains wiring should not be connected to a circuit with an external on/off switch.

• For best aesthetic condition, place sensors at ends of row only so as not to break the continuous lens.

• For better occupancy coverage in longer rows, sensors may be placed mid run, but keep in mind this will break the continuous lens into discrete sections. Alternatively, remote sensors may be used, note the same wiring rules will apply.

Occupancy Sensor Coverage:

Note: Longer dimension of detection area (Y1, Y2) is parallel to longer dimension of the luminaire.

Daylight Sensor

The light sensor measures the total amount of light in a circular field of approximately 80% of the PIR detection area. The following aspects should be observed during installation:

• Minimum distance from the window = 2ft (0.6m).
• Prevent light reflections from outside entering the sensor (for example sunlight reflection on a car hood) as this will lead to incorrect light regulation.

As a guideline the formula 0.72 X H can be used to calculate the minimum distance between the window and sensor whereby H is the height from the bottom of the window to the sensor.

ft)
3 m (9.8 ft)| 2.4 m (7.9 ft)| 3.6 m (11.8 ft)| 3.6 m (11.8 ft)| 5.4 m (17.7 ft)

The detection area for the movement sensor can be roughly divided into two parts;

• Minor movements (person moving = 3ft/s or 0.9m/s).
• Major movements (person moving = 3ft/s or 0.9m/s).

Photosensor spatial response

ATTENTION: Install in accordance with national and local building and electrical codes.

CUSTOMER SUPPORT

© 2023 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner.
Signify North America Corporation.
400 Crossing Blvd, Suite 600 Bridgewater,
NJ 08807. Telephone: 855-486-2216
Phone: 604.888.6811
Web: ledalite.com/products
Revision D
November 6, 2023
ignify Canada Ltd.
281 Hillmount Road, Markham,
ON, Canada L6C 2S3.
Telephone: 800-668-9008

References

• Indoor architectural lighting | Ledalite | Signify

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>