trend T8EK Electric Router Instruction Manual

trend T8EK Electric Router

OVERVIEW

Thank you for purchasing this Trend product, we hope you enjoy many years of creative and productive use.

TECHNICAL DATA

The vibration and/or noise emission level given in this information sheet has been measured under a standardized test given in EN62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission level represents the main applications of the tool. However, if the tool is used for different applications, with different accessories or poorly maintained, the vibration and/or noise emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration and/or noise should also take into account the times when the tool is switched off or when it is running but not doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintaining the tool and the accessories, keeping the hands warm (relevant for vibration), organizing work
patterns.

WARNING: To reduce the risk of injury, read the instruction manual.

Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

• DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.
• WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
• NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
  • Denotes risk of electric shock.
  • Denotes risk of fire.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power Tool Use and Care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/ or the battery pack, if detachable, from
  the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Instructions for Routers

• Hold the power tool by insulated gripping surfaces only, because the cutter may contact its own cord. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electrical shock.
• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by your hand or against the body leaves it unstable and may lead to loss of control.
• Keep handles dry, clean and free from oil and grease. This will enable better control of the tool.
• Maintain a firm grip with both hands on the tool to resist starting torque. Maintain a firm grip on the tool at all times while operating.
• Keep hands away from cutting area above and below the base. Never reach under the workpiece for any reason. Keep the router base firmly in contact with the workpiece when cutting.
• Never touch the bit immediately after use. It may be extremely hot.
• Be sure that the motor has stopped completely before you lay the router down. If the bit is still spinning when the tool is laid down, it could cause injury or damage.
• Be sure that the router bit is clear of the workpiece before starting the motor. If the bit is in contact with the workpiece when the motor starts, it could make the router jump, causing damage or injury.
• The permitted speed of the cutting bit must be at least equal to the maximum speed marked on the power tool. If cutting bits run faster than their rated speed, they may break and fly off.
• Always follow the bit manufacturer’s speed recommendations as some bit designs require specific speeds for safety or performance. If you are unsure of the proper speed or are experiencing any type of problem, contact the bit manufacturer.
• Do not use cutters larger than 50mm unless the router is fitted in a router table. Do not use cutters larger than 65mm in this tool.

RESIDUAL RISKS

WARNING: We recommend the use of a residual current device with a residual curTent rating of 30mA or less. In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:

• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS

Electrical Safety
The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate.

• Your tool is double insulated in accordance with EN62841; therefore no earth wire is required. If the supply cord is damaged, it must be replaced only by Trend Tool Technology Ltd or an authorised service organisation.

Using an Extension Cable
An extension cord should not be used.

PACKAGE CONTENT – (Fig. T)

• 1 x Router (A)
• 1 x Micro-adjustable side fence (B)
• 1 x Collet (C)
• 1 x Collet sleeve (D)
• 1 x Centring pin (E)
• 1 x 30mm guide bush (F)
• 1 x Guide bush adaptor (G)
• 1 x Trammel pin (H)
• 1 x Vertical dust adaptor (I}
• 1 x Cyclone dust adaptor (J)
• 1 x Under fence dust adaptor (K)
• 1 x Height adjuster (L)
• 1 x Router Table Safety Clip (M)

ONLY FOR ROUTER TABLE USE

• 1 x 22mm Spanner (N)
• 1 x Moulded carry case
• 1 x Instruction manual
  • Check for damage to the tool, parts, or accessories which may have occurred during transport.
  • Take the time to thoroughly read and understand this manual before operation.

MARKINGS ON TOOL

The following pictograms are shown on the tool.

DESCRIPTION OF PARTS

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

1. Variable speed dial
2. Main handles
3. Depth stop rod
4. Depth stop locking knob
5. Spindle lock
6. Collet
7. Depth stop turret
8. Router base
9. Micro-adjustable side fence
10. Height stop rod
11. Thumb wheel
12. Height adjuster
13. Spanner
14. Fine height adjustment knob
15. Fine height adjustment gauge
16. Plunge locking lever
17. Side fence locking knobs
18. Router table safety clip insertion point
19. On/off trigger switch
20. On/off trigger switch release button

Intended Use
The TB router has been designed for trade/medium-duty routing of wood, wood- based materials, and plastics. These routers are intended for routing grooves, edges, profiles, and slots as well as copy routing. DO NOT use under wet conditions or in the presence of flammable liquids or gases. The TB is a professional power tool. The TB is designed so that it can be installed into a router table. The router may only be installed in tables that meet the legal safety requirements for router tables. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

• Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children} suffering from diminished physical, sensory, or mental abilities; or lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.

CAUTION: Before operating any of the controls, read the following sections.
Plunge Locking Lever (Fig. B1-B2)

1. Lever (16) Position (12-3 O’clock} Plunge setting is locked and cannot move.
2. Lever (16) Position (6 O’clock} Plunge lock is disengaged. Perfect for fast repositioning and surface registration when used with a jig.

How to fit the Collet sleeve – (Fig. C2)
This router is supplied with a collet sleeve as an accessory. To fit the collet sleeve (b} simply slide it into the collet (a}. The collet sleeve has a flange to ensure insertion to correct depth.

NOTE: Do not attempt to remove the collet from the collet nut.

Depth Stop Turret – (Fig. E)

WARNING: Do not change the depth stop the turret while the router is running. This will place your hands too near the cutter head. The depth stop turret (7) limits the downward distance that the tool can be plunged. It serves to define the depth of the cut by limiting the travel of the depth stop rod (3).

1. The cutting depth can be set by turning the appropriate height on the depth stop turret.
2. The depth stop turret is rotatable with stepped stops.
3. It is the interaction of the depth stop rod and the depth stop turret that determines the routing depth.
4. Refer to the section Adjusting the Depth of Cut for instructions on how to use the depth stop turret in an actual operation.

Height Stop Rod and Thumb Wheel (Fig. G)
The height stop rod (10) and thumb wheel (11) limit how high the unit can travel up the rails. The system is adjustable to limit the rise of the plunge to full up where the bottom of the collet is 80mm above the workpiece.

NOTE: It is easier to move the thumb wheel UP if the plunge locking lever is locked and easier to move the thumb wheel down if the unit is first moved down by releasing the plunge locking lever and then tightening it.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn the tool off and disconnect the tool from the power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

Installing and Removing a Cutter – (Fig. C1, F)

• WARNING: Do not tighten the collet without a cutter fitted.
• WARNING: Always use cutters with shanks that match the diameter of the collet.
• WARNING: Do not use cutters larger than 50mm (2″) unless the router is fitted in a router table.
• CAUTION: Care should be taken when removing the cutter to avoid cuts to fingers.

Installing a Cutter

1. Insert at least 3/4 of the shank length of the cutter into the collet assembly (6).

2. Press the spindle lock (5) forward until the router spindle is locked.
   NOTE: You may need to turn the spindle slightly to engage it.

3. Turn the collet nut counterclockwise with the supplied 22mm spanner (13) to tighten it.

Removing a Cutter

1. Press the spindle lock button (5) forward until the router spindle is lock.
2. Turn the collet nut (6) clockwise with the supplied 22mm spanner (13) to loosen.
3. Keep turning the spanner until the collet nut tightens and then loosens again. This is the fail safe mechanism releasing the collet.
4. The cutter should now slide out.
   NOTE: Each time you finish using a cutter, remove it and store it in a safe place.

Fine Height Adjuster – (Fig. A, D)

• CAUTION: Ensure that the plunge locking lever is unlocked. Never use unnecessary force to rotate the fine height adjuster mechanism.
• CAUTION: DO NOT remove the screw on hex nuts. The fine height adjuster can be used in portable mode or when the router is held inside a table.

Fine Adjustment
When not using a depth template, or if the depth of the cut needs readjustment, it is recommended to use the fine height adjuster (14).

1. Adjust the depth of cut as described in Adjusting the Depth of Cut.
2. Set the fine height adjuster to zero using the fine zero reset ring (15).
3. Rotate the fine height adjuster (14) to the required position: one turn corresponds to approximately 1 mm and 1 mark to 0.1mm.

Fitting Guide Bush and Inner Plate – (Fig. H)

1. Turn the router upside down.
2. Fit the inner plate (58) into the recess in the router base plate (8). The raised side of the inner plate must be away from the router base. Loosely fit the two pan head machine screws (59) through the inner plate and into the tapped holes. DO NOT TIGHTEN SCREWS.
3. Fit the 30mm guide bush (24) to the inner plate (58). Fit the guide bush with the two M5 countersink machine screws (25). Tighten these screws.
4. Fit line up pin (60) into the collet (6) depending on the size fitted) in the router, lightly tighten the collet nut to hold the line-up pin (60).
5. Release the plunge locking lever and gently depress the base until the line-up pin (60) projects through the 30mm guide bush (24).
6. Once in line, tighten the pan head machine screws (59) with a flat screwdriver.

Fitting the Micro-Adjustable Fence – (Fig. I, J)

1. Fit the guide rod (26) to the router base (8).
2. Slide the parallel fence (27) over the rods.
3. Tighten the wing bolts (28) temporarily.

Adjusting the Micro-Adjustable Fence – (Fig. A, I, J)

1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact with the workpiece.
3. Position the router on the cutting line.
4. Slide the parallel fence (27) against the workpiece and tighten the wing bolts (28).
5. Adjust the parallel fence using the fine adjustment knob (29). The outer cutting edge of the cutter must coincide with the cutting line.
6. If required, loosen the screws (30) and adjust the strips (31) to obtain the desired guiding length.

Dust Extraction – (Fig. A, K, P)
Dust from materials such as lead-containing coatings and some wood types can be harmful to one’s health. Breathing in the dust can cause allergic reactions and/or lead to respiratory infections of the user or bystanders. Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood treatment additives. Observe the relevant regulations in your country for the materials to be worked. The vacuum cleaner must be suitable for the material being worked. When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a dust class M vacuum cleaner.

Connecting Dust Extraction Adaptor – (Fig. K)
The dust extraction adaptor consists of a main section (32), a cover (33), an extraction tube adaptor (34), one extraction tube screw (37), two base screws (52), and two nuts (36)

1. Slide the cover (33) onto the main section (32) until it clicks into place.
2. Place the main section (32) on the base and secure it with two screws (52) and nuts (36).
3. Remove screw (37) from the top of the router and use this screw to assemble the extraction tube adaptor (34) to the router.

Connecting Dust Extractor Hose – (Fig. P)

WARNING: Risk of dust inhalation. To reduce the risk of personal injury, ALWAYS wear an approved dust mask.
WARNING: ALWAYS use a vacuum extractor designed in compliance with the applicable directives regarding dust emission when sawing wood. Vacuum hoses of most common vacuum cleaners will fit directly into the dust extraction outlet. Connect a dust extractor hose (38) to the extraction tube adaptor (34). A dust extraction tube adaptor (34) is supplied with your tool. Vacuum hoses on most vacuum extractors will fit directly into the dust extraction spout.

NOTE: When using dust extraction, be sure that the dust extractor is out of the way and secure so that it will not tip over or interfere with the router or workpiece. The dust extractor hose and power cord must also be positioned so that they do not interfere with the router or workpiece. If the dust extractor or dust extractor hose cannot be positioned properly, it should be removed.

OPERATION

Instructions for Use

• WARNING: Always observe the safety instructions and applicable regulations.
• WARNING: To reduce the risk of serious personal injury, turn the tool off and disconnect the tool from the power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

Proper Hand Position – (Fig. 0)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction. Proper hand position requires both hands on the main handles (2).

Using the Router – (Fig. A, L)

CAUTION: Turn the router on before plunging the cutter head into the workpiece.

CAUTION

• Excessive cutting may cause an overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 15mm at a pass when cutting grooves with an 8mm diameter bit.
• When cutting grooves with a 20mm diameter bit, the depth of cut should not be more than 5mm at a pass.
• For extra deep grooving, make two or three passes with progressively deeper bit settings.

CAUTION: After long periods of working at low speeds, allow the machine to cool down by running it for three minutes at maximum speed, with no load. All common routing tasks can be performed with the plunge-cut router on all types of wood and plastic:

• Grooving
• Rebating
• Recessing
• Veining
• Profiling

To prevent overload of the tool by using the wrong speed selection, follow the recommended settings below:

• Do not use cutters larger than 50mm unless the router is fitted in a router table.

NOTE: Only carbide tipped cutters should be used on panels faced with plastic laminates. The hard laminates will quickly dull steel cutters.
NOTE: For better plunge sliding movement, frequently clean the columns of dust or debris. If the plunging movement is not moving as smooth as desired, lubricate the columns with a dry Teflon lubricant.

1. After setting the cutting depth as described, locate the router such that the cutter is directly over the place you will be cutting.
2. With the router running, lower the unit smoothly down into the workpiece. DO NOT JAM THE ROUTER DOWN.
3. When the tool reaches the pre set depth, turn the plunge locking lever (16) to lock.
4. When you have finished routing, push the plunge locking lever (16) to unlock and let the spring lift the router directly out of the workpiece.
5. Always feed the router opposite to the direction in which the cutter is rotating. Refer to Fig. L.

On/Off Trigger Switch – (Fig. A)

WARNING: To reduce the risk of serious personal injury, turn the unit off and disconnect it from the power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

1. To turn the unit on, press the trigger release button (20) and then squeeze the on/off trigger switch (19). Continue to squeeze the trigger switch for continuous running.
2. To turn the unit off release the trigger.

Variable Speed Dial – (Fig. A)

WARNING: If the speed control ceases to operate, or is intermittent, stop using the tool immediately. Please contact Trend Tool Technology Ltd or an authorized service facility for repair.

NOTICE: The router is equipped with electronics to monitor and maintain the speed of the tool while cutting. In low and medium-speed operations, the speed control prevents the motor speed from decreasing. If you expect to hear a speed change and continue to load the motor, you could damage the motor by overheating. Reduce the depth of cut and/or slow the feed rate to prevent tool damage. Refer to the Speed Selection Chart to choose a router speed. Turn the speed dial (1) to control router speed. The lowest speed is 10,000 and the highest speed is 26,000 rpm using the speed dial (1).

1. Turn the speed dial to the required position. The dial is numbered from 1 – Max. and corresponds to router speeds of 10,000 rpm to 26,000 rpm.
2. Use the slower settings for large-diameter cutters and the faster settings for small-diameter cutters.
3. The correct setting will also depend on the density of the material, depth of cut, and feed speed of the router.

NOTE: A noticeable loss of motor rpm means motor overload.

The speeds in this chart are approximate and are for reference only. Your router may not produce the exact speed listed for the dial setting.

WARNING: Always follow the cutter manufacturer’s speed recommendations as some bit designs require specific speeds for safety or performance.

If you are unsure of the proper speed or are experiencing any type of problem, contact the cutter manufacturer.

LED Worklights – (Fig. F)

CAUTION: Do not stare into the worklight. Serious eye injury could result. Two LED work lights (57) are located next to the collet assembly (6).

1. The work lights (57) will constantly illuminate when the router is connected to the main power supply.
2. To switch off the work lights the router must be disconnected from the mains power supply.

NOTE: The work light is for lighting the immediate work surface and is not intended to be used as a flashlight.

Moulding Natural Timbers

WARNING: When routing always lock the plunge locking lever. When edge molding natural timbers, always mold the end grain first, followed by the long grain. This ensures that if there is breakout, it will be removed when the long grain is routed.

Adjusting the Depth of Cut – (Fig. A, E)

1. Place the router with the cutter fitted onto the workpiece.
2. Set the depth stop turret (7) as required.
3. Loosen the locking knob (4) securing the depth stop (3).
4. Lower the router slowly until the cutter touches the workpiece and secure it in place by locking the plunge with the plunge locking lever (16).
5. Set the required depth by adjusting the distance between the bottom of the depth stop and the depth stop turret.
6. Tighten the locking knob to secure the depth stop.

NOTE: By rotating the depth stop turret, eight depth settings can be quickly made.

Direction Of Feed – (Fig. L)

WARNING: Avoid climb-cutting (cutting in a direction opposite than shown in Fig. L). Climb-cutting increases the chance for loss of control resulting in possible injury. When climb-cutting is required (backing around a corner), exercise extreme caution to maintain control of the router. Make smaller cuts and remove minimal material with each pass.

The direction of the feed is very important when routing and can make the difference between a successful job and a ruined project. Fig. L show proper direction of feed for most cuts.

1. When routing along an edge, the direction of the router travel should be against that of the rotation of the cutter. This will create the correct cutting action and prevent the cutter from snatching. It will also pull the router towards the workpiece and the side fence or guide bearing will be less likely to wander from the edge of the workpiece.

Feed Speed
The speed at which the cutter is fed into the wood must not be too fast that the motor slows down, or too slow that the cutter leaves burn marks on the face of the wood.

NOTE: Practice judging the speed by listening to the sound of the motor when routing.

Using a Side Fence – (Fig. M)

CAUTION: Ensure the working position is comfortable and at a suitable working height.

1. Ensure the wing bolts (28) are fully released. Slide the guide rods (26) into the routing base (8) and tighten the wing bolts.

2. Adjust the fence fine adjustment knob (29) to the required distance and clamp in place with the wing bolts (28).

3. Then lower the cutter height until the cutter is just above the workpiece.

4. Fine adjustments are possible by loosening the wing bolt (28) and adjusting the side fence fine adjustment knob (29).

5. Tighten the wing bolt (28) to secure the position.
   NOTE: One revolution of the side fence fine adjustment knob (29) equals 2.0 mm of side feed.

6. Lower the cutter onto the workpiece and set the cutter height by to the required distance. Refer to Setting the Router Depth.

7. Switch the router on and after the cutter reaches full speed, gently lower the cutter into the workpiece and lock the plunge.

8. Feed along the workpiece, keeping sideways pressure to ensure the side fence does not wander away from the workpiece edge and downward pressure on the inside hand to prevent the router from tipping.

9. When finished, raise the router, secure it with the plunge locking lever (16), and switch the router off.

NOTE: When starting the cut, keep the pressure on the front cheek until the back cheek contacts the workpiece edge.
NOTE: At the end of the cut, keep pressure on the back cheek until the cut is finished. This will prevent the router cutter from swinging in at the end of the workpiece and nipping the corner.

Side Fence Routing – (Fig. I, J)
The side fence is used to guide the router when molding, edge profiling or rebating the edge of a workpiece or when routing grooves and slots in the center of the workpiece, parallel to the edge. The edge of the workpiece must be straight and true. The strips (31) are adjustable and should be set ideally with a 3 mm gap on each side of the cutter.

Guiding Off a Batten
Where an edge guide cannot be used, it is also possible to guide the router along a batten clamped across the workpiece (with an overhang at both ends}.

Freehand Routing

WARNING: Make shallow cuts only! Use cutters with a max. diameter of 12mm. Your router can also be used without any sort of guide, e.g. for signwriting or creative work.

Table Mode – (Fig. A, Q)

WARNING: Before the TS is installed into the router table, check that the router table meets all of the legal safety requirements for router tables. Read all safety warnings, instructions, and specifications provided with the router table. Failure to follow all instructions and safety rules may result in electric shock, fire, and/or serious injury.

WARNING: To reduce the risk of serious personal injury, turn the unit off and disconnect it from the power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

WARNING: Do not use the TS as a handheld router if the Table Safety Clip is installed.

Installing the Router Table Safety Clip

1. Secure the safety strap from the clip to the leg of the router table, ensuring that the buckle strap is a safe distance away from the cutter.

2. Ensure the router and NVR (No volt Release) switch is disconnected from the power supply.

3. Push the Clip (40) onto the right-hand side handle (2) by guiding the pin into the insertion point (18) and ensuring that the lower guide is located correctly into the bottom of the handle.

4. Press the Trigger Release button (20) and squeeze the On/Off Trigger (19). The trigger will stay depressed, and the power is now locked on.

5. Install the router in the table according to the table manufacturer’s instructions and connect power plug to the NVR switch.
   WARNING: Do not secure the safety strap to the router

6. Switch on the power supply to the NVR. The router is now ready for use.
   NOTE: The power on/off function of the router is now controlled by the NVR switch and will start-up at the preset speed as soon as the NVR is turned on.

7. When removing the router from the table, the safety clip can be pulled from the handle.
   Fitting the Height Adjuster – (Fig. S1)
   The height adjuster (12) for the TB can be used portable or when the router is held inverted in a table. If a suitable size access hole is drilled into the router table top, the height adjustment can also be adjusted from above the tabletop.

To set up for fine height adjustment:

1. Plunge router and lock the plunge locking lever ..
2. Rotate the thumb wheel (11) up the height stop rod until it is close to the router casting fork (62).
3. Align the base of the thumb wheel (11) so that it will locate in the fork (62).
4. Release plunge locking lever.

CAUTION: DO NOT use a powered drill to drive the height adjuster assembly. Only use the supplied handle. Ensure that the plunge locking lever is unlocked. Never use unnecessary force to rotate the mechanism. Do not undo the Torx® screw on hex nuts.

Using Without the Height Adjuster – (Fig. S2)
In portable use the thumb wheel (11) should be wound to the top of the height stop rod and hand tightened against the hex cap. The base of the knurled nut (11) should be aligned with the fork (62) in the router casing.

CAUTION: In normal plunge mode, ensure the base of the knurled nut is aligned correctly with the forks of the lower motor housing. This will enable the cutter to retract into the base safely.

For Portable Use:

1. Place the height adjuster (12) onto the top threaded spindle hex nut (51).
2. Rotate the handle clockwise to raise the motor body and reduce cutter depth.
3. Rotate the handle anti-clockwise to lower the motor body and increase cutter depth.

For Router Table Use – (Fig. S3)

1. Ensure the router is fitted into the router table, see opposite page.
2. Place height adjuster (12) through router table hole onto bottom threaded spindle hex nut (64).
3. Rotate the handle clockwise to raise the motor body and raise the cutter height.
4. Rotate the handle anti-clockwise to lower the motor body and lower the cutter height.

One revolution corresponds to 1.5mm. The height adjuster handle dial (63) can be reset to zero.

Prior to Operation

1. Check that the cutter is correctly installed in the collet.
2. Set the cutting depth.
3. Connect a dust extractor.
4. Make sure the plunge locking lever is locked before switching on.

Routing with Bearing Guided Cutters – (Fig. R)
Where a parallel guide or guide bush are inappropriate, it is possible to use bearing guided cutters (50) for cutting shaped edges. Trend offers a wide range of bearing-guided cutters for various applications. Please see trend- uk.com for details.

Trend Base Configuration – (Fig. N)
This router has three threaded holes (53) built into the base that allow it to attach to other Trend accessories.

MAINTENANCE

Your power tool has been designed to operate over a long time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn the tool off and disconnect tool from the power source before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

Repairs
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance, and adjustment (including power cord repairs, and brush inspection and replacement, when applicable) should be performed by a Trend service center or a Trend-authorized service center. Always use identical replacement parts.

Lubrication

• Your power tool requires no additional lubrication.

Cleaning

• WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and an approved dust mask when performing this procedure.
• WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Optional Accessories

WARNING: Since accessories, other than those offered by Trend Tool Technology Ltd, have not been tested with this product, the use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Trend Tool Technology Ltd recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories.

Storage

• After use return the tool to its storage box.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing as waste. Accessories and packaging should be sorted for environmentally friendly recycling. Separate collection. This product must not be disposed of with normal household waste.

Household User
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites, or by retailers when you purchase a new product. Please call Trend Customer Services for advice as to how to dispose of unwanted Trend electrical products in an environmentally safe way or visit www.trend-uk.com

Business Users
Please call Trend Customer Services for the disposal of unwanted Trend electrical products.

WARRANTY

The jig carries a manufacturer’s warranty per the conditions on our website www.trend-uk.com For the location of your nearest Trend Service Agent, please call Trend Customer Services or see our stockist locator at www.trend- uk.com

UK DECLARATION OF CONFORMITY

The undersigned, representing the following manufacturer

Manufacturer
Trend Tool Technology Ltd, Watford, England WD24 7TR declares that the products):

Product Identification

• Product: Plunge Router
• Brand: Trend
• Model: T8E

Conforms to the following UK Regulations

• The Supply of Machinery (Safety) Regulations, 2008, S.I. 2008/1597 (as amended).

• Electromagnetic Compatibility Regulations, 2016, S.I. 2016/1091 (as amended).

• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, S.I. 2012/3032 (as amended).and the following Designated Standards:
  S.I. 2008/1597:

  • EN 62841-1+2015+AC:15
  • EN 62841-2-17:2017

• S.1. 2016/1091:

  • EN 55014-1:2021
  • EN 55014-2:2021
  • EN 61000-3-2:2019+A1:2021
  • EN 61000-3-3:2013+A1:2019+A2:2021

The undersigned is responsible for the compilation of the technical file and makes this declaration on behalf of Trend Tool Technology Ltd. Neil McMillanTechnical Director Trend Tool Technology Ltd, Odhams Trading Estate, Watford, WD24 7TR,

England

• Place of issue : Watford England
• Date of issue : 14/04/2023

The undersigned, representing the following manufacturer

Manufacturer:
Trend Tool Technology Ltd, Watford, England WD24 7TR declares that the products):

Product Identification

• Product: Router
• Brand: Trend
• Model: T8EL

Conforms to the following UK Regulations

• The Supply of Machinery (Safety) Regulations, 2008, S.1. 2008/1597 (as amended).
• Electromagnetic Compatibility Regulations, 2016, S.I. 2016/1091 (as amended).
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, S.I. 2012/3032 (as amended).and the following Designated Standards:
  • S.I. 2008/1597:
  • EN 62841-1+2015+AC: 15
  • EN 62841-2-17:2017
  • S.I. 2016/1091:
  • EN 55014-1:2021
  • EN 55014-2:2021

The undersigned is responsible for the compilation of the technical file and makes this declaration on behalf of Trend Tool Technology Ltd.ryNe reck Neil McMillan Technical Director Trend Tool Technology Ltd, Odhams Trading Estate, Watford, WD24 7TR, England

• Place of issue : Watford England
• Date of issue: 14/04/2023

Declaration of Conformity Router Product Ref. We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and conform with the following standards. Technical file at:

Trend Tool Technology Ltd. Natford, WD24 7TR, England

• Tel: 0044(0)1923 249911
• technical@trendm.co.uk
• www.trend-uk.com

EU Importer
Trend Tool Technology Ltd. 3rd Floor, Kilmore House, Park Lane, Spencer Dock, Dublin 1, Ireland

• Trend Tool Technology Ltd. 2023.
• All trademarks acknowledged E&OE

No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Tool Technology Ltd. cannot be held liable for any material rendered unusable or for any form of consequential loss. E&OE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>