HCS RC366C Remote Control Replacement IR Instructions
- June 10, 2024
- HCS
Table of Contents
HCS RC366C Remote Control Replacement IR
Product Information
Specifications:
- Model: RC3662811/01BR
- FCC ID: 2AGOFRC366C
- Compliance: FCC Part 15, Industry Canada’s license-exempt RSSs
- RF Exposure Compliance: FCC and ISED radiation exposure limits
Product Usage Instructions
Getting Started
Before using the remote control, ensure you have read the user manual
completely.
Battery Installation
Open the battery compartment on the back of the remote and insert the
required batteries following the correct polarity.
Pairing the Remote
If needed, follow the instructions in your device’s manual to pair the
remote control with the corresponding device.
Basic Operations
Use the buttons on the remote to navigate through menus, change settings,
and control your device.
Maintenance
Keep the remote clean and avoid exposure to water or extreme temperatures
to ensure optimal performance.
Frequently Asked Questions (FAQ)
-
How do I replace the batteries?
To replace the batteries, open the battery compartment on the back of the remote, remove the old batteries, and insert new ones following the correct polarity. -
Can I use this remote with multiple devices?
Depending on the compatibility, you may be able to use this remote with multiple devices. Refer to the user manual of your specific device for instructions on pairing.
Know your Remote
BLE Manual Pairing
- Step 1: input 2*AAA batteries to Battery compartment.
- Step 2: point the remote to the STB IR receiver.
- Step 3: Pressed & hold <
> & <<Digit 1>> keys for more than 3 seconds. - If pairing is successful, the STB LED will blink 2x (short pulse).
- If the pairing is unsuccessful, the Both STB & TV LED will blink 4x (short pulse).
- The remote can be unpaired by pressing <
> & <<DIGIT 9>> for more than 3 seconds. The STB LED will blink 2x (short pulse) if un-pairing is successful.
Voice Function
RCU features a button to activate the Voice Search application to search for content by speaking through the remote’s built-in microphone.
FCC information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This product has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This product generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
IC information:
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF exposure statement
This equipment complies with the FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>