IRIS ISCT-800 Industrial Series Center Table Instructions

June 4, 2024
IRIS

IRIS logo

INDUSTRIAL SERIES CENTER TABLE
GENERAL INSTRUCTIONS

ISCT-800 Industrial Series Center Table

Rank you for purchasing this product. Read these instructions carefully before use. Keep these instructions for future reference.

Too1 Required

  • Cross-head Screwdriver

WARNING
Do not use an impact driver.

IMPORTANT

  • READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY.
  • FOLLOW ASSEMBLY INSTRUCTIONS PROPERLY TO ENSURE MAXIMUM PRODUCT STRENGTH AND STABILITY.
  1. Tightening Pin Screw clockwise using a Phillips screwdriver
  2. Tightening Drum
    (1) Insert tightening drum: Being careful of orientation, insert the drum to the back with an etched arrow at the top. (Drum cannot be secured if oriented incorrectly)
    (2) Insert the tightening pin into the hole
    (3) Turn tightening drum: Secure by turning 135-180 degrees clockwise.IRIS
ISCT 800 Industrial Series Center Table fig1

INCLUDED PARTS

IRIS ISCT 800 Industrial Series Center Table fig2

ASSEMBLY METHOD

  • ASSEMBLE INDOORS ON A FLAT SURFACE, AND BE WARY OF SCRATCHES ON THE FLOOR FROM ASSEMBLY.
  • VERIFY THAT ALL PARTS ARE PROPERLY INSTALLED.
  1. Attach the tightening pins to the desktopIRIS ISCT 800 Industrial Series Center Table fig3
  2. Attach the side boards to the desktopIRIS ISCT 800 Industrial Series Center Table fig3
  3. Attach the backboard 4 Attach the bottom boardIRIS ISCT 800 Industrial Series Center Table fig4
  4. Attach the bottom boardIRIS ISCT 800 Industrial Series Center Table fig5
  5. Attach the felt stickers and leg pipes, and temporarily tighten the screws for the leg pipes.IRIS ISCT 800 Industrial Series Center Table fig6  
  6. Attach the frame pipes and temporarily tighten them
    After assembling each part, fully tighten all the screws and bolts. Complete

WARNING

  • Make sure the bolts and screws have been thoroughly tightened
  • Make sure the product is straight and sturdy
  • Make sure all the legs have contact with the floor

PRECAUTIONS

FOR SAFE USAGE, OBSERVE THE FOLLOWING:
FOR INDOOR STORAGE USE ONLY

  • Do not place the product near a heater or any other source of healthier.
  • Keep the product on a flat and stable surface.
  • Do not allow children to play with products.
  • Do not exceed the weight capacity.
  • When a moving product, take all items off.
  • Assemble correctly according to the assembly method in this manual.
  • Use of this product on the flooring or other easily damaged floor surfaces may result in scratches or dents on the floor surface, so use sufficient caution.
  • When placing items on a product, distribute weight evenly.
  • There may be oil adhering to the pipes, so wipe it off promptly.
  • Keep away from direct sunlight or high humidity.
  • Wipe away any water, oil, or soap immediately.
  • Do not place hot or wet items on the product.
  • Do not place stickers or tape on the product.
  • If the product becomes unbalanced or unstable, please remove some of the stored items.
  • Check that screws are properly tightened after installation. Screws may loosen over time and re-tighten as needed.
  • No refund will be provided for accidents or damages caused by natural disasters, improper usage, or unauthorized modifications made to the product.
  • Follow the local rules and regulations when disposing of products or packing materials.
  • Placing the product in a well-ventilated area is recommended before first use.

MAINTENANCE

TO MAINTAIN THE OPTIMAL PERFORMANCE OF THE PRODUCT, OBSERVE THE FOLLOWING:

  • Do not scrub the wooden shelf surface hard while cleaning. It may damage the surface.
  • To remove hard stains, wipe with soap and water using a non-abrasive cloth and dry the product thoroughly.
  • Do not use cleaning products such as alcohol, gasoline, bleach, or detergent powder.
PRODUCT SIZE (mm) W31.50 x D14.96 x H16.14 in / W800 x D380 x H410 mm
WEIGHT CAPACITY (lbs/kg) Desktop: 33 lbs / 15 kg, Bottom Board: 4 lbs 12 kg,

Overall: 37 lbs / 17 kg
MATERIAL| Wooden parts: Synthetic resin cosmetic particle board, Printed paper cosmetic particle board, Medium Density Fiberboard
Pipe: Steel (epoxy powder coating)

  • WEIGHT CAPACITY IS THE MEASURED VALUE. NOT GUARANTEED VALUE.
  • PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Attn: Customer Service (Returns Department)
IRIS USA, Inc.
13423 West Cactus Road
Surprise. AZ 85379 02021 IRIS USA. Inc.
All rights reserved.
877282 020621-0W-GRJ.03 IRIS logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals