VEVOR 0102 Pottery Wheel 25CM Pottery Forming Machine User Manual

POTTERY WHEEL MACHINE
USER MANUAL

0102 Pottery Wheel 25CM Pottery Forming Machine

NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
[email protected]

WARNING

Important Safety Tips

• Please read carefully and understand the following safety tipsbefore using this product.
• For your safety, please guarantee that this appliance always is plugged into a properly grounded circuit.
• Do not cut or remove the third prong ( ground ) from the power plug or attempt to use a grounding adapter.
• Never immerse the machine in water.
• Always keep the machine away from any water source. Avoid splashing water into the device or the motor.
• Never use an extension cord to power the machine.
• Do not use water pipes for cleaning. Unplug the power plug when not in use or before cleaning. Never use spray solvents or other flammable cleaning agents on or near the equipment.

APPLICATION

Ideal for pottery school, classroom and large-scale entertainment training center to make finished pottery crafts as well as the teach- ing ceramics, etc.

CAUTIONS

Before the operation, please check whether the power supply voltage match- es the specified voltage of the device. Place the pottery wheel on the dry & flat surface. Keep away from inflammable and explosive substances.

METHODS OF OPERATION

1. Insert the power plug into the 220V/110V power socket, turn on the black leakage protection switch, and wait for the power indicator to light up.
2. Turn the rotation switch (forward or backward) as you like.
3. Use the foot pedal to control speed, the working turntable will start to accelerate until it reaches working speed.

TRANSPORTATION AND STORAGE

During transportation, this product should be handled preciously to prevent violent vibration. Generally, it should be placed in a well-ventilated, non- cor- rosive warehouse rather than be stored in the open air for a long time. Never put it upside down. Rainproof measures should be adopted when storage temporarily.

IMPORTANT SAFETY TIPS

• Please read carefully and understand the following safety tips before using this product.
• For your safety, please guarantee that this appliance always is plugged into a properly grounded circuit.
• Do not cut off or remove the third plug (ground cable) of the power plug or try to use the ground adapter.
• Never immerse the machine in water.
• Always keep the machine away from any water source. Avoid splashing water into the device or the motor.
• Never use an extension cord to power the machine.
• Do not use water pipes for cleaning. Unplug the power plug when not in use or before cleaning. Never use spray solvents or other flammable cleaning.

MAINTENANCE

• When using the pottery machine, it is recommended to put an extra small water basin in the water basin (on the machine) to facilitate cleaning the clay on your hand.
• During daily cleaning, use a dry cloth to wipe off the grease on the machine, don’t flush it with water directly.
• Pay attention to cleanliness and prevent the clay from entering the bearing, which affects the long-term use.
• Please turn off the leakage protection switch and restore the rotary switch to its original position, if the machine not in use.

SPECIICATIONS

Pottery Wheel Machine
One machine has two speed regulation modes, which can be controlled by hand or foot.
Manual speed regulation mode: LCD touch speed regulation. Pedal control speed: forward acceleration, backward deceleration. You just need to adjust to your own speed to pull the ceramics directly.

Basic Parameters:

Pottery Wheel Machine

One machine features two ways of speedcontrol. You can push handle or footpedal control speed. Manual Speed Control: push forward to accelerate, pull back to decelerate. Pedal Control Speed: step forward for acceleration, step back for deceleration. Basic Parameters:

Pottery Wheel Machine
This pottery wheel has a removable water basin. Pedal in the horizontal position means the fastest speed. Back pressure to 45 degrees is for the stop state. After  speed fixed, you can lift your foot off thepedal. Basic Parameters:

Pottery Wheel Machine
Pedal in the horizontal position means the fastest speed. Back pressure to 45 degrees is for the stop state. After speed fixed, you can lift your foot off the pedal.

Basic Parameters:

Pottery Wheel Machine
This product is electric manual speed regulation. The speed can be adjusted by the knob on the front.
Basic Parameters:

Disposal: This product is subject to the provision of european Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to acollection point for recycling electrical and electronic devices.

EC REP: EUREP GmbH
Unterlettenweg 1a, 85051 Ingolstadt
[email protected]
+49 841 8869 7744
Website: wwwyvevor.com
E-mail: [email protected]
Tel/Fax : (+ 626) 275-4507 (for USA)
(+ 44) 1173182739 (for Europe)
(+001) 626 275-4507 (for Other Countries)
Working Time: Mon-Fri 8 : 00am to 5 : 00pm
Manufacturer: Yanshan Jiacheng Ceramic Equipment Manufacturing Co., LTD
ADD: Cui Liu Yang Industrial Zone, Yangji Town, Yanshan County, Cangzhou
City, Hebei Province Made in China ‘
E-mail: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>