Iris Innovations PoE4v2 Power Over Ethernet Injector Hub User Guide
- June 12, 2024
- Iris Innovations
Table of Contents
- Iris Innovations PoE4v2 Power Over Ethernet Injector Hub User Guide
- PoE4v2
- QUICK START GUIDE
- Rugged & Compact
- Plug & Play
- Operation
- PoE4v2
- What’s in the Box?
- Installation
- ESSENTIAL SAFETY NOTICES:
- EMC Guidelines:
- Water Ingress:
- SELECTED SPECIFICATIONS:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Iris Innovations PoE4v2 Power Over Ethernet Injector Hub User Guide
PoE4v2
Wide DC Input Voltage Range PoE Injector
QUICK START GUIDE
Thank you for choosing the PoE4v2 Power over Ethernet (PoE) Injector Hub from
Iris Innovations.
This document is designed to provide a brief overview of the product, it’s
features and installation instructions. Full instructions, regulatory and
safety information can be downloaded from our website: www.boat-
cameras.com
Iris offer a range of network power injectors to complement
our extensive portfolio of rugged IP CCTV cameras and network equipment. The
PoE4v2 has been designed
Rugged & Compact
With its stylish and compact form factor, the PoE4v2 chassis is manufactured from an extruded aluminium design with high quality and rugged industry standard connectors, designed for reliable operation throughout its life.
Plug & Play
The PoE4v2 Injector is a Plug and Play device with no configuration or setup
required. Simply connect your network cables as required, apply DC power and
you’re good to go!
The PoE4v2 operates over a wide DC input range of 9 ~ 30VDC.
Operation
The PoE4v2 Power over Ethernet Injector Hub features 4 powered ethernet ports
and a passive ‘uplink’ port.
Each port is capable of delivering power up to 30W per port with a maximum
power budget of 60W. Therefore, if 4 devices are connected, the maximum power
for each port will be 15W.
The PoE4v2 is IEEE802.3af / 3at compliant.
PoE4v2
Dimension Drawing
What’s in the Box?
The following parts are included with your PoE4v2
1 x PoE4v2 Power Injector
1 x 2 Core Power Input Cable 1 x Quick Start Guide
Installation
Ensure the device is installed in a clean, dry environment away from excess
heat sources, moisture and excessive vibration.
Before you fix the PoE4v2 into position, take time to ascertain there is
sufficient space around the unit to allow ventilation and to take into account
cable strain relief.
The PoE4v2 can either be screwed into place using a surface mounting kit
(optional) or, due to its very light weight, fixed using strong Velcro pads.
Do not drill through the unit.
Connect the power connector supplied ensuring the correct polarity is
observed.The power connectors are push-pin type. Use a small flat bladed screw
driver to push in the tab on top of each terminal and hold, insert each power
cable ensuring polarity is correct, fully into the terminal and then release
the tab to grip the wire in place.
ESSENTIAL SAFETY NOTICES:
Product Disposal and Recycling:
Dispose of this product in accordance with the WEEE Directive. The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electronic and electrical equipment. Iris Innovations supports the WEEE policy and politely request you observe correct disposal methods. For further information on how to correctly dispose of this product please contact Iris Innovations. Please recycle unwanted packaging and documentation. The cardboard carton, all paper manuals and documents and the protective plastic bag in which the camera is shipped are widely recyclable. Please check with your local recycling plant for confirmation.
EMC Guidelines:
This product is designed to be used as a power supply for a visual aid or part of a visual aid system and is not part of the vessels navigational system – even if used in conjunction with other on board equipment or third party systems – and is compliant with the EMC directive 2014/30/EC. The original Declaration of Conformity (DoC) is available from our website The camera should not be installed on the ships helm or in close proximity to radio receiver equipment. We recommend the camera is installed no closer than 1m from any equipment transmitting or cables carrying radio signals – particularly VHF radios and associated equipment. The device needs to be powered from a clean DC Power Supply fitted with an adequately rated fuse to profile the necessary electrical protection in accordance with its operating power ratings.
Water Ingress:
Disclaimer: This product has not been tested to environmental ingress
protection levels (IP30 rating) and is therefore not for external use. It must
be installed in a clean, dry environment in accordance with the instructions
provided in this document. Any evidence of water or moisture damage will
invalidate the product warranty.
Full product safety, warning and compliance information, including Declaration
of conformity is available from www.boat-cameras.com
SELECTED SPECIFICATIONS:
Full specifications are listed in the complete product guide which can be downloaded from our website.
Manufactured & Assembled in the United Kingdom
Read More About This Manual & Download PDF: