Leitner Riviera Electric Bike User Manual

Leitner Riviera Electric Bike

Important: To provide the best experience this manual is continuously updated. To make sure that you are referring to the most up-to-date information download the latest version at leitner.com.au/manual.

About this manual

• Thank you for purchasing a Leitner electric bike. We take pride in providing electric bikes at an outstanding value, delivered to your factory directly. Riding an ebike can be fun, however for safety reasons it is important to only ride the bike after reading and understanding the complete manual.
• Thefollowingmanualisonly a basic guide to assistance and not a complete or comprehensive manual of all aspects of assembling, maintaining, repairing and using your bicycle. In the interest of safety, we recommend that you visit a local electric bike professional to assemble, tune and regularly service the bike.
• This manual makes no representation of the safe use of this bike under all conditions. It is impossible to predict all situations when riding a bike and there are risks associated with riding this bike which cannot be avoided. These risks are the sole responsibility of the rider.
• his assembly and operation manual shall remain an integral part of the electric bicycle. When you transfer the electric bicycle to others, please enclose this manual as it contains important safety guidance and operation instructions. Anyone riding the electric bike shall carefully read the safety guidance and operation instructions before their first ride.

Meaning of Safety Language.
Riding a bike can cause injury and in extreme cases death, therefore it is important to read and understand the manual before using the bike. The most common cause of injury is falling off the bicycle and reading the manual will help to avoid situations that put you at risk of injury or death.

• WARNING! Indicates the possibility of injury or death.
• Caution! Indicates the possibility of injury.

As there are different models of eBikes, pictures are for reference only and may show a similar component from another model. Certain instructions of this manual may not apply to your model. All content in this manual is subject to change or withdrawal without notice. We made an effort to provide accurate information, however, we do not assume responsibility or liability if any errors or inaccuracies appear. If you are unsure about certain parts of this manual, if you have a problem or need repair, please visit the website www.Leitner.com.au and email a customer service representative at sales@Leitner.com.au with a problem description and pictures and videos or call 1300 856 725.

Guide to safe operation

Mechanical and electrical work performed on your ebike. Safety depends on correct assembly and maintenance. The use of a torque wrench is recommended to tighten bolts correctly. Special tools and skills are necessary to comprehensively service this bike. In the interest of safety, we recommend that you visit a skilled local electric bike mechanic to assemble, tune and regularly service the bike.

WARNING! Modifying or tampering with your bike can provide a safety risk.

• Non-original components that are not approved or have incorrect assembly can cause accidents and injury. Do not make any modifications including but not limited to installing incompatible forks, drilling, sanding, filing or removing parts.
• Third-party components and accessories can provide a safety risk. Examples are bicycle trailers, bicycle carriers and child seats. Installation and use at the customer’s risk.
• Original components can be purchased through your retailer. Consult your retailer for safety and compatibility advice. For example, installing a seat post that is too long may put stress on the frame leading to damage.
• The electric parts do not need maintenance. Do not open electric parts. Disassembly of the bike beyond the state in which it has been delivered in the retail box voids the warranty.
• If your bike has been tampered with, it is advised to replace non-original components with genuine components and have the bike safety-checked by a skilled bike mechanic to ensure safe operation.
• Replacement of inner tubes with a suitable inner tube of a reputable brand is not considered tampering.

Riding a bike in different conditions
WARNING! Using a bike in conditions beyond its limits and the skills of the rider could lead to damage to the bicycle, fork, frame, parts and injury. Do not use your bike on rough trails, trails with obstacles, areas where tyres are momentarily off the ground, jumps, technical areas, speeds over 25 km/h and for aggressive riding. Do not ride down curbs.

• Riding an ebike can be fun for commuting, exercise or recreation if you ride your bike in a manner that is within your ability and the limits of the bike. Ride carefully and be mindful of your environment to avoid dangerous situations. Bikes are limited by use, surface, maintenance and design.
• Leitner e-bikes are designed for use on paved surfaces with shallow gradients where the tyres are always on the ground.
• Permissible total payload: Weight limit of rider (including luggage) 120kg (264 pounds). The maximum total weight (rider + luggage + bike) is approximately 145kg. The empty weight of the bike including the battery approximately 25kg. Do not ride on hills steeper than 15 per cent incline.

WARNING! Smooth gravel roads and loose surfaces increase the risk of losing control. Your riding style needs to be adjusted. Apply brakes gently, go around turns slowly be careful not to use the motor during turns and do not accelerate quickly.

Bikes do not protect you in accidents. You may damage the bike, or fall and it may cause serious injury or death.

WARNING! Riding a bike after an impact beyond its limits, e.g. accident may cause the bike to break at lower than standard loads. It is recommended to have the bike inspected by an ebike mechanic before riding it again.

Riding instructions

• Use your brakes carefully: if your bike has two brake levers it is recommended to press both brake levers at the same time. Check which brake lever engages which brake. In Australia, normally the right lever engages the front brake, and the left lever the rear brake. In the USA, normally the right lever engages the rear brake. Over-using the front brake lever may cause the rear wheel to lift resulting in loss of control.
• Always keep a safe distance from other vehicles or objects. Get to know your brakes by practising in a flat, safe location with concrete surface at low speeds. Adjust brakes if they are too powerful or too weak.
• Do not use the electric assistance to begin with. If you are comfortable riding the bike without electric assistance, read all instructions about using electric assistance, then ride a bike using low assistance levels.
• Always be prepared to press the brake levers in case you accelerate unexpectedly. Do not switch your bike on unless you are ready to ride it to prevent accidental acceleration. Also, refer to the section “Changing gears correctly” in this manual.
• Go around turns carefully, do not pedal around turns, and keep your pedal arms horizontal to avoid pedals touching the ground.

WARNING! Incorrect use of brakes, gears and electric controls may cause loss of control and injury.

When you ride, include a pump, a spare inner tube, a puncture repair kit, and tools so you can repair your bicycle if it has a flat tyre or other mechanical problem. It is not recommended to ride at night. If you do ride at night, include a spare light source for emergencies.

WARNING! Prevent toe-overlap. Be aware of situations where your feet which are on the pedal touch the front wheel. In normal riding situations the front wheel is not turned sufficiently to allow contact of your toes with the wheel, however this may occur when going around tight turns at low speeds. Do not pedal when going around turns. Toe overlap is affected by the size of your feet, the pedals, crank arms, mudguards and tyres.

• Carrying cargo will change the way your bike handles, including braking distance, steering, acceleration, balancing, and hill-climbing ability. Cargo should not protrude too far from your bike and a low centre of gravity is recommended.
• When riding in coastal areas, wipe your bike after every ride as salt water and humidity are very corrosive. Apply anti-rust treatment to spokes and other unpainted parts. Do not use anti-rust sprays. It may contaminate unwanted parts such as brake pads. Damage from corrosion is not covered under warranty.

WARNING! Avoid pinch points (squeezing hazard), moving parts, hot parts and sharp points. Examples of parts that can cause injury are turning wheels including spokes, sharp cogs driving the chain, hot brakes, hot brake rotors after use, folding frame, folding stem and folding seat posts.

• Frame and forks need to be inspected thoroughly before every ride for any unusual signs of damage or wear. If you experience any unusual noise during riding stop using the bike. After impacts, for example, accidents or hitting an object at low speeds or if the bike falls inspect the bike including the frame and fork closely as it may have been damaged due to high stress. If there are scratches, use clear nail polish to touch up to avoid corrosion.
• Noise: The A-weighted emission sound pressure level at the driver’s ears should be less than 70 dB(A).

The life span of your bicycle

• Bicycle parts will wear with use and may need replacement after some time. If a bike is used more often parts will need to be changed more frequently as compared to a bike which is only used occasionally. Rough, intense riding will reduce the life span of the bike. There are many factors determining the lifespan of a part therefore it is not possible to give an exact timetable for replacement.
• Frequent maintenance will increase the lifespan. If you are in doubt about whether a part should be changed please contact customer service. Battery capacity will naturally degrade over time and with use.

WARNING! If the lifespan of any part is exceeded it may break and cause injury therefore it is necessary to inspect all parts of the bike regularly to identify damaged components and replace them before they fail.
WARNING! As with all mechanical components, the bike is subjected to wear and high stresses. Different materials and components may react to wear or stress fatigue in different ways. If the design life of a component has been exceeded, it may suddenly fail, possibly causing injuries to the rider. Any form of crack, scratches or change of colouring in highly stressed areas indicates that the life of the component has been reached and it should be replaced.

Checklist before each ride

To make sure that the most important components are installed correctly and functioning correctly it is necessary to follow this checklist before each ride. Please note this is not a full maintenance program.
WARNING! If a part of your bicycle is not working properly do not ride your bike. Have the part installed correctly using the adjustment instructions in this manual or have the part repaired or replaced by a skilled bike mechanic. Contact customer service if in doubt.

Checklist

• Battery: Make sure your battery is fully charged, secured and not damaged.

• Frame and fork: Are there signs of stress or fatigue? Discolouration, cracks, dents, chips, irregularities in shape, scratches, unusual noises. Frame folding mechanism safely installed?

• Handle-stem and handle-bar: Is the stem aligned with the front wheel? Walk to the front of the bike, and put the front wheel between your legs (Figure FS2.) Check if the wheel and stem are aligned straight. Try to twist the handlebar left and right. The handlebar should not be loose and shouldn’t move if moderate force is applied. Make sure that all cables are not stretched and that there is enough slack for all cables when turning handle-bar. Make sure the wheel can be turned freely without entangling wires. The ends of the handlebars need to be covered, usually by a handle grip to protect from injuries. Replace if damaged. Apply the front brake and move the bike forward and backward. Is the fork loose? If it is loose the headset needs to be adjusted. Folding mechanism safely installed? Push the handlebars down with force to make sure it’s stable and not loose.

• Wheels: Are wheels installed safely? Lift the wheel off the ground, hit it by hand from the top and try to move it by hand left and right. The wheel shouldn’t move or come loose. Check if the nuts or quick-release system is holding the wheel in place safely Are tyres inflated to the recommended pressure on the sidewall of the tyre? E.g. 50psi. Pump the tyre using a hand bicycle pump (not supplied). Do NOT use an automated air compression pump, for example, the car tyre pumps at gas stations. Check if the wheel is straight. Lift it off the ground and spin it by hand observing any wobbles from side to side where it passes the brake pads. WARNING! Wheels need to be installed safely otherwise they may come loose during a ride and cause injury.

• Brakes: Check if all brakes on the bike work well. Pressing the lever should stop the bike. Also, make sure that the brake pads are not rubbing excessively against the rim of the wheel or the disc of a disc brake: Lift the wheel off the ground and spin it. If there are any noises or if the wheel stops spinning abruptly it indicates that the brakes are rubbing. Caution! Do not touch the disc of the disc brake after use as it may be hot. Never touch the brakes while the wheels are turning. Check that engaging the brakes switches off the motor.

• Saddle (seat) and seatpost: Use both hands to twist the seat left and right push the seat up and down and try to tilt the seat forwards and backwards. It should not move or be loose. Check that the minimum insertion mark on the seat post is NOT visible.

• Suspension: Make sure that any suspension installed on the frame or fork cannot be compressed fully. Increase front fork suspension stiffness if needed by turning the adjustment knob. Generally clockwise makes the suspension stiffer. Not all forks have an adjustment knob.

• Reflectors, front and rear lights: Make sure both front and rear lights face the correct direction and that they are clean and working properly. Make sure that all reflectors on the front and rear wheels and on the pedals are clean and not covered by any accessories.

• WARNING! A bike without properly functioning lights and reflectors may be hard to see by other people increasing the chance of an accident.

• Pedals and crank-arms: Check that pedals are fully inserted into crank arms and that they are tightened to specification. The pedals and the crank arm should not be loose. Loose pedals will damage the thread on pedal arms. Damaged pedal arms need to be replaced.

Safeguard your bicycle

• Purchase a strong lock to prevent theft. Always lock your bike.
• Note your frame serial number. It is located at the front of the frame on top of the front fork. If you have problems locating your serial number please contact customer service.
• Park your bike undercover, out of direct sunlight protected from rain, snow, water, sea water and wind in a safe location that does not obstruct traffic and is clear from hazardous conditions including heat and cold. Humidity especially in areas close to the sea can cause corrosion. UV exposure can cause rubber to crack and paint to faint.
• Park your bike in a manner that it doesn’t fall. Falling may damage the bike, most commonly on the handlebar, handle grips, gear shifter and rear derailleur.
• If the bicycle is stored for an extended time it should be lifted off the ground with tyre pressure at half of the recommended level. Charge the battery at least every month as per the respective battery maintenance chapter in this manual.
• Clean your bike every week with a moist rag. Any parts that rub against the frame can remove paint or in extreme cases damage to the frame. Use protective padding material if needed to protect the frame.
• Do not clamp the frame during transportation to prevent accidental damage. Use sturdy adapter bars for transport which attach at the seat post and handle-stem. Always use adapters that can carry the weight of the bike. Remove the battery for transport if needed to reduce the weight of the bike.
• Cover bikes which are transported on the outside of a vehicle with a suitable cover to prevent exposure to weather.
• Always make sure that no cables are overstretched and that parts of the bike that touch are separated appropriately for example using rags or other padding material.
• To ship a bike in a box wrap frame parts with padding, for example, a foam sheet or bubble wrap. Pack the bike in the same manner as it has been received by you if you have received a bike in a box. Keep the original packing material and box in the unlikely case the bike has to be shipped again. Make sure the bottom of the fork is protected to prevent it from penetrating the box.
• When parking, lock the battery into the frame and remove keys or remove the battery to prevent theft.
• Check with your local authorities whether it is allowed to transport the bike with public transport.

Drinking Bottle
If your bike has been supplied with a drinking bottle, wash the bottle two times with clean water and detergent before use. Wash the bottle after every use. Dry bottle before storage. Inspect the bottle regularly for any unusual appearance or smell.

Maintenance

Regular maintenance ensures that the bike is in good condition to be ridden safely. The recommendations below are for normal use. If your bike is used more frequently it needs to be maintained more often. If any parts need repair, fix or replace them immediately.

Tools for maintenance

• Torque wrench (recommended) showing Nm or lb/inch units
• Allen keys: 2, 4, 5, 6, 8 mm
• Open end spanners: 8, 9, 10, 13, 15mm
• Phillips head screwdriver
• Bicycle tyre pump with gauge
• Spoke spanner
• Bike tyre repair kit including tyre removal levers and spare inner tube
• Grease and lubricant
• Not all tools are necessary for all bikes.

Important Notice! Having the electric bike assembled, adjusted and serviced by a competent electric bike mechanic is the best practice and it will reduce the risk of injury.

Best practice:
A competent electric bicycle mechanic should perform the following tasks:

• Assembly and full check after assembly, including tuning of spokes.
• After 30 days: Check and re-tuning. After the first days of riding some components may need re-adjustment, for example, brake or gear wires may stretch. Disc brakes may need several weeks to “brake-in” until they reach optimum performance.
• Every 600 miles (1000km) or every year, whichever comes first: full service

Maintenance schedule

• Before each ride: refer to the “Checklist before each ride” section in this manual
• Every week: clean with a moist rag, and check for loose spokes. Tighten loose spokes with a spoke spanner (not supplied) to a tension similar to neighbouring spokes. It is best practice to have spokes adjusted by a skilled bike mechanic.
• Monthly check: wheel bearings, rim wear, Stem bolts, headset-bearing, pedals, chain wear, cable wear, gear levers, derailleur, brakes, stand, accessory bolts, suspension fork bolts, rear suspension bolts, reflectors, lubricated forks, lubricated derailleur. Check the battery for signs of damage and anything unusual.
• Every three months: Check crank arms and bottom brackets, lubricate brake levers and brake-arm fixing bolts.
• Every Year: Lubricate handlebar stem, lubricate seat post, replace grease: on pedal threads, in bottom bracket bearings, in wheel bearings, in headset bearings. Lubricate quick release on wheels and seat-post, and folding pivots (frame, seat post, handle-stem). Inspect the motor for any unusual noise. Bleed hydraulic disc brake fluid by a professional mechanic.

Before your first ride
Contact a customer service representative to assist you in finding a bike which has the right size for you. Important measurements are the minimum and maximum seat height form the ground to the top of the seat and also the stand- over height.

Figure SO1: Stand-over height: To determine the minimum leg length of the rider refer to the figure on the left.

1. Top tube height of bicycle from the ground. A straight top tube is shown. Step-through frames (sometimes referred to as “Ladies” frames) are specified based on corresponding straight top-tube models.
2. Crotch measurement of rider: Wearing bicycle shoes and having the feet 6 inches apart, measure the inside of the leg from the ground to the crotch.
3. There should be at least 1 inch (25 mm) clearance between the crotch measurement of the rider and the top tube height of the bicycle when straddling the bike. For mountain bikes, at least 2-3 inches of clearance is recommended.

• Read and understand the complete manual.
• Adjust seat and handlebar height and tilt for best comfort. Always make sure that minimum insertion marks on the seat post and handle e are inserted into a frame so that marks are not visible.
• Familiarize yourself with the controls and practise braking and steering at low speeds in a flat, paved, safe environment and always be prepared to apply brakes in case of unexpected acceleration.
• Do not switch on your bike on unless you are ready to ride it to prevent accidental acceleration. Switch the bike off while pushing it. If you have any doubts contact customer service.

Rules to ride safely

• Cycling involves the risk of injury and damage. By choosing to ride this bicycle you assume the responsibility for that risk.
• This electric bike is intended only for riders 18 years or older who are physically and mentally capable of riding an electric bicycle. Consult your doctor to confirm the suitability of riding an ebike as impairments or disabilities may increase the risk of injury or death. Parents and guardians are responsible for the activities and safety of children. This bike is not designed to be used by children.
• Familiarise yourself and comply with your local and national electric bicycle laws as every state may have different regulations. Consult your local authorities for advice including reflectors and lighting..
• Always ride carefully looking out for other participants in traffic. Bicycles may be hard to see, therefore always ride slowly and defensively being ready to brake to stop your bike. Use your bell.
• Always avoid obstacles in the road like potholes or curbs. If there are rail or tram tracks cross them at a 90-degree angle to avoid getting caught in the tracks and losing control. Expect opening car doors or cars backing out of driveways. Don’t use items that may restrict your hearing.

Always wear a helmet while riding which complies with your local safety standards.

• Do not wear loose clothing which could get caught in the moving parts of the bicycle.
• WARNING! Do not ride at night, in wet weather, icy conditions, snow or other adverse conditions like wind. Your braking power may decrease, braking distance may increase and you will have less control over the bike if the ground is more slippery. Electric components may get damaged in wet conditions.
• Make sure that all your reflectors and lights are working and installed correctly. Front and rear lights may increase your visibility in conditions with low light, however, reflectors only increase your visibility if the light is pointed at them. Wear high-visibility clothing with bright and reflecting materials.
  WARNING! Riding in low visibility conditions like night, dusk, dawn or fog will increase your risk of collision as other people may not see you.

Always think about safety and apply common sense when riding. Some examples are:

• Do not ride when intoxicated, if you are impacted by medication, extremely tired or if you do not feel well. Always ride carefully and slowly being prepared to stop the bike. Only ride on roads that are bicycle-friendly. Try to avoid roads with heavy traffic passing you at a small distance.
• Always keep your hands on the handlebar. If riding in a group, ride in a single file, keep a safe distance from other riders and generally try to avoid riding in a big group as it may increase the risk of accidents.
• Only one person should ride the bike. Do not carry a second person on the bike. Riding off-road will increase the risk of damage or injury. Only ride on trails, do not ride in the rain, or through water and avoid all obstacles. Make sure that at no time obstacles hit any parts of your bike including your bike stand. Always make sure that there is enough clearance between the bike and the ground. Do not attach loose objects to your bike.
• Do not jump, do not perform stunts, do not ride over obstacles like curbs, sticks and other obstacles, do not ride in rough terrain, do not ride unusually.

WARNING! Riding incorrectly can lead to damage and injury.

OPERATION OF YOUR ELECTRIC BIKE

• Your e-bike is driven by a motor embedded in the hub (centre) of the rear wheel. The motor is powered by a battery. The amount of power delivered to the motor and hence the accelerating force on the e-bike is controlled by you.
• There are two systems to activate the motor: Throttle and Pedal Assist.
• The throttle can be twisted by hand and activates the motor (Figure C1).
• In Pedal Assist mode (Figure C2), the motor is triggered when you pedal forward, and the power assist will stop when you stop pedalling. In other words, power assist happens as long as you pedal. You don’t need to pedal hard. All you need is to apply a light force to the pedals continuously to maintain continuous rotation. When you apply one of the brakes, the power assist will automatically stop, allowing the e-bike to slow down or stop. Power assist will turn itself off before the e-bike has reached the maximum speed of approximately 25 km/h
• You should use the gear shifter at the handlebar to set the gears appropriately according to road conditions and pedal as usual. Please refer to the relevant section in this manual on how to use gears.
• Note that the Battery level indicators on the display (Figure C3) will only show an estimate of the battery charge level when power is not being drawn from the battery (the bike standing still). While using motor assistance voltage will decrease.

Figure C1: The twist-and-go throttle (2) is located on the right-hand side of the handlebar, next to the handle grip (3). Push the red button (1) IN to switch the throttle on. Push the red button (1) again, so that it moves OUT to disable throttle.
Grabbing the throttle with your right index finger and thumb wrapped around it and twisting it down in the direction of the white arrow will activate the motor and the ebike will move forward. The twist acceleration is gradual: Twist it down only a little bit for moderate acceleration. Twist it down for maximum acceleration. The throttle will accelerate the bike to a maximum speed of about 6 km/h (walking speed). If your throttle overrides the pedal assist system meaning if you twist the throttle you can only go 6km/h, even if you use pedal assist, then release the throttle to use the pedal assist system. The throttle can be unlocked to go about 25 km/h for use on private property. If the throttle is unlocked the bike must not be ridden on public roads. Please refer to the relevant section of this manual on how to unlock the throttle.

WARNING! Only switch the throttle ON if you intend to ride the bike. Always switch the throttle and bike OFF when walking next to the bike and push the bike to prevent accidental acceleration. Always be ready to press the brake lever (4) to stop the bike.

Start-up assist provides mild power assistance up to 6km/h (walking speed) : Push and hold the “-” button on the display (Figure C2). This mode can be used to help push the bike while walking next to it or it can provide gentle assistance when starting to ride the bike. If the start-up assist mode overrides the pedal assist system, meaning you can only go 6km/h even if you use the pedal assist, then release the “-” button to use the pedal assist system.

• The button panel (Figure C2) controls several features on your ebike.
• WARNING! Only switch Pedal assist ON if you intend to ride the bike. Do not pedal when riding through curves! Always switch Pedal assist OFF when walking next to the bike and push the bike to prevent accidental acceleration. Always be ready to press both brake levers to stop the bike.
• Switch bike ON: Ensure the battery is charged and installed, then push and hold the “Power” button on display until the LCD screen switches on.
• Switch bike OFF: Push and hold “Power” button until display switches off.
• Turn on lights: push the “lights” button
• Push the “Information” button to cycle through a menu of the display (Figure C3). ODO: Odometer, total distance travelled MAX: Maximum speed. AVG: Average speed. TRIP: distance travelled in one trip.
• To reset the trip meter to zero push and hold the “+” and “-” buttons at the same time until you see “Tc-n”. Press the “+” button to change it to “Tc-y”. Push and hold the “Information” until the trip-meter is reset, displaying “0”.
• To activate the “Pedal Assist” push the “+” button briefly to increase the power and speed, push the “-” button briefly to decrease the power and speed. “Pedal assist” means that the motor will be activated when you start pedalling and the bike will move forward with motor assistance while you are pedalling. The higher the pedal assist level, the more power assist you will receive. The maximum pedal assist level is 5. At maximum assistance, the motor will accelerate to approximately 25 km/h.

USB Port

If your display is equipped with a USB port, a USB cable (not supplied) may be connected to provide power to an electric device, for example, a mobile phone. Please note Leitner does not take any liability for any damage or loss of data loss of devices connected to the USB port. If devices are used while riding, ensure they are safely attached to the bike, stay aware of your surroundings and ride safely. Ensure the USB port is covered to protect it from water and dust.

Bell

Reflectors

• Every 3 months check that all reflectors are clean, installed securely and not covered up by any accessories.
• Reflectors need to be installed at the front (facing forward, colourless) and rear of the bike (facing backward, red) on the pedals and on spokes on the front and rear wheels. If the red rear reflector is installed on the seat post and interferes with battery removal, do as follows: tighten it so that it is installed securely but not overly tight so that it can be twisted to the side to make space for battery removal. After the battery is installed, twist the red rear reflector so that it faces backwards.

Getting Started

• First, unpack your electric bike carefully making sure that you don’t scratch the bike with sharp tools such as paper knives or scissors.
• Keep all packing material including the carton in the unlikely case the bike has to be re-packed and shipped.
• Locate all parts: battery, keys, front wheel, mudguards, charger, seat and seat post, front light, handle-stem, pedals, tools and any small parts like nuts or screws inside the shipping carton.
• Sometimes small parts like nuts or screws may come loose during shipping so be sure and check the bottom of the carton and protective wrapping carefully. Please note that eBikes are fragile items. Although we are using first-class courier services and the bikes are professionally packed they can get damaged during transit.
• Please check the bike for damage and any missing parts upon arrival and let us know immediately. We will then work with you on a solution and ship replacement parts as soon as possible.

Assembly Instructions

• This bicycle has been disassembled for shipping. To ship the bike, the pedals, front light, front mudguard, seat, front wheel, handle stem and handlebar may be loosened or removed.
• Different parts of the bikes such as brakes and gears may need adjustment. This manual will list the steps required for installation.
• Check all nuts and bolts on the bike, even if parts have already been assembled by the factory, to make sure that they are installed safely.
• In the interest of safety, It is recommended to have the bike assembled and adjusted by a bike mechanic and serviced regularly.

Installation of mudguards and front light

https://youtu.be/QA6thIYA9P8.

Ensure all parts of the front and rear mudguards and wires have at least 6mm clearance from the tire and wheel. Tighten all screws and bolts on both mudguards.
WARNING: If the front and rear mudguards are not correctly installed, they may prevent the wheel from spinning or turning while riding and cause serious injury or death. Check tightness of all bolts, screws and correct installation every 30 days.

QUICK RELEASE LEVERS

How to operate quick-release levers

• Step 1: Close Lever (figure Q1). If the lever closes very easily (less than 12 pounds or 53 Newton) it indicates that it is loose. If the lever is very hard to close completely (more than 45 pounds or 200 Newton), don’t force it and go to step two.
• Step 2: Open the lever. If the lever was too loose, tighten the nut. If the lever was too hard to close, loosen the nut. Close the lever again.
• Step 3: Repeat step 2 until the lever is firmly closed and can’t move. Do NOT turn the lever like a wing nut to close as this will not close it firmly.

WARNING! Quick-release levers must be closed in such a position so that the lever won’t be accidentally hit while riding causing it to open. If the quick-release lever is not closed safely, components of the bike can loosen while riding causing serious injury or death.

INSTALLATION OF FRONT WHEEL

WARNING! Before each ride make sure that the front wheel is installed safely using the quick-release system. Lift the wheel and hit it from above with your hand to make sure that it won’t move and that it is stably installed into the fork. When trying to move the wheel by hand from left to right, the wheel must not move. Refer to the guide on how to operate quick-release levers. Failure to do so may result in serious injury or death.

The handlebar and stem are used to steer the bike. The handle stem connects to the fork. Some stems can be adjusted in height to provide a comfortable riding position. The rider’s response to steering and braking can be adversely affected if not installed or used correctly.

Installation

Figure HS5: View from riders perspective. The handle-stem neck (9) is folded all the way down to expose the stem attachment bolt (10) which is located several cm inside the stem (not visible in this picture). Insert an Allen key (12) into the stem to tighten the stem attachment bolt (10) to 12 Nm.

Figure HS6: View from the rider’s perspective. While the quick-adjust lever (7) is open, the position of the handlebar (6) and the angle of the handle- stem neck (9) can be adjusted. Use an Allen key (14) to adjust the tightness of the tension bolt (13) before closing the quick-adjust lever (7). After the quick-adjust lever (7) is fully closed (Figure HS6), push down hard on both grips of the handle-bar (6, Figure HS4) to ensure the handle-bar (6) and handle-stem-neck (9) are installed safely and don’t move. If they are loose, open the quick-adjust lever (7, Figure HS4) and tighten the tension bolt (13). Repeat this process until the handle-bar (6) and handle-stem-neck (9) are installed safely. Also, refer to the “quick-release lever” section in this manual to ensure the quick-adjust-lever (7) is closed tightly. Always ensure that the safety slider (8, Figure HS4) is fully and safely closed to prevent the quick-adjust- lever (7) from opening accidentally.

• Figure HS7: To align the stem with wheel, walk to the front of the bike, put wheel between your legs and adjust the handle-stem and handlebar position. Tighten lower steerer clamp bolts (11, Figure HS1) to 10-15 Nm

Ensure that the handle-bar (6, Figure HS1) is attached to the stem at the centre of the handle-bar. If needed adjust the position using the quick- release mechanism (8 and 7, Figure HS4).
WARNING: Always ensure the quick-release mechanism is locked securely before riding. Failure to do so may cause serious injury or death.

• Figure HS8: Safely closed quick-adjust mechanism. The quick-adjust lever (7) is fully closed and the safety slider (8) is locked, preventing the quick-adjust lever (7) from opening accidentally.

Installation of pedals

• Pedals are marked „L‟ (LEFT) and „R‟ (RIGHT) on the axle end. You need to look carefully to locate the engraving. Lubricate the thread of the pedal with lubricant (available at bike shops)
• Carefully position the pedal at a 90-degree angle (straight) to the crank arm. Don’t insert washers between the pedal and pedal arm. Use your hands. Don’t use a tool. Don’t use force!
• The left pedal needs to be turned anti-clockwise into the crank arm on the LEFT side of the bike
• The right pedal needs to be turned clockwise into the crank arm on the RIGHT side of the bike.
• The pedal will screw in without resistance if it’s placed correctly into the thread. If you feel resistance, don’t continue! Unscrew the pedal and start again.
• Use your hands to screw the pedal in, so that the thread is not visible anymore.
• Once the pedal is in, use a spanner and tighten the pedal up very firmly (40 Nm) so that it won’t come off while riding. Remember: clockwise for the right pedal and anti-clockwise for the left pedal. It is necessary to check that the pedals are tight before every ride as they may loosen up over time.

WARNING! Incorrect installation and failure to check pedal installation before each ride may cause the thread on the pedal arm and pedal to be damaged, resulting in the pedal falling off while riding. DO NOT insert washers between the pedal thread and the crank arm as it may prevent the pedal from gripping correctly and eventually causing damage to threads. Incorrect pedal installation may cause serious injury or death.

Crank arms and bottom bracket
Check the Allen bolt at the centre of both crank arms, left and right-hand side. (right arm shown in picture). If the arms are loose, tighten the bolt with an 8mm allen key (key not supplied) to 40Nm. Don’t over tighten. It is necessary to check the crank arms regularly as they may get loose over time. The bottom bracket is the bearing system which is attached to the pedal arm. Move the crank arm with one hand towards the bike frame and hold the bike with the other hand at the seat post. The arm shouldn’t move if the bottom bracket is tight. There should be no noise or looseness while riding the bike. If there is excessive movement, have the bike serviced by a bike professional.

The rear rack
The rear rack must be installed as shown in the picture. Make sure the rack is stable and safe before using it. Tighten all nuts and bolts of the rack to 16 Nm, including the ones attaching the rack to the frame towards the centre of the wheel. The maximum weight limit on rear rack: 25kg (55 pounds).

WARNING! To avoid injury make sure the rack is installed safely and that your luggage does not affect the bike negatively. Make sure your luggage is not getting caught in spokes which could cause serious injury or damage. Do not attach a trailer to the rear rack.

Seat (saddle) and seat post

Note: General seat post shown. Your model may vary slightly.

Inspection: Before each ride make sure all nuts, bolts and quick releases are safely installed. Use both hands and move seat left and right or up and down. If seat moves easily, tighten bolts. Inspect seat-post every 30 days to make sure it is straight. If it is bent, contact customer service.
Recommended seat position: To check for the correct seat height, sit on the seat, put one heel on the pedal in the down position while the crank arm is parallel to the seat tube. Adjust seat height until your leg is straight. If the knee is bent, raise the seat. If your hips rock for the heel to reach the pedal, lower the seat. For people of short stature the seat should be adjusted to a height so that the feet of a seated rider can reach the ground.
WARNING! Adjust height, position on rail and tilt of seat to a comfortable position. Do not continue to ride if you feel pain, discomfort or numbness while riding.
WARNING! If seat post is too high and not inserted at least 12cm (4.7 inch) into frame, the frame or post may break and cause injury. The minimum insertion mark must not be visible when seat is inserted into frame. The minimum insertion mark is printed or engraved on the seat post. You may have to look closely to identify it.
WARNING! If nuts, bolts and quick-releases are not tightened safely the seat position may change unexpectedly during ride and cause injury.
Caution! When you open the quick-release the seat may drop down and present a squeezing hazard. Always hold the seat with one hand to prevent it from dropping and operate quick-release lever with other hand.
WARNING! Cover any coil springs under the saddle if a child-seat is fitted to prevent trapping of fingers.

Headset
The headset is the system of bearings which sits around the handlebar and fork it needs to be checked every 30 days by applying the front brake while moving the bicycle back and forth. To check if steering is smooth, lift front wheel off the ground and steer left and right. If there is excessive movement or if steering is not smooth, the headset needs to be adjusted by a bicycle professional.

To adjust seat tilt and position on rail loosen the seat fixing bolt. Stay between rail maximum marks. Tighten to 18-20 Nm or the Nm indicated on the seat post. Right hand side of seat shown. Same setup on left hand side of seat.

WARNING! Stay within maximum marks or the rail may brake.

Chain
Check chain tension every month. If it is too lose use derailleur to adjust tension. Check all links of the chain. If there are any stiff links, apply chain lubricant and try to move them carefully by hand or have them replaced at a bike shop.

Bike stand (Kick-stand)
Make sure the stand is fully retracted before riding the bike. The stand is designed to only carry the weight of the bike. When you are on the bike, do not lean against the stand. Do not use the stand if there is any luggage on the bike. Do not use the stand if there is a person on the bike. Make sure that the stand does not hit obstacles while riding. If your stand hits obstacles while riding, adjust riding style or remove stand. Every 30 days check if the stand is attached safely to the bike. Tighten stand attachment if needed. WARNING! Always hold onto bike when loading bike to prevent falling. Do not assume that the stand alone supports the bike.

DISC BRAKES
General information about brakes: The brake system allows you to decrease speed or your bicycle. This operation is very important to your safety. Only use original brake pads.
WARNING! Brakes needs to operate correctly to avoid injury! Always ensure that the brakes are working correctly before riding the bike. If your hydraulic disc brake does not work properly have it maintained by a local professional bicycle mechanic. Failure to do so may result in serious injury or death.

Figure DB1: Disc Brake Assembly: View from left side. A mechanical disc brake is shown. Hydraulic disc brakes work according to the same principle, however a fluid inside a brake line is used to transfer pressure from the brake lever to the brake pads.
How disc brakes work: Disc brake pads apply pressure to a disc mounted to the hub of the wheel (Figure DB1). The pressure is controlled with a hand lever on your handle-bar that is connected to the brake caliper with a brake line. Do not press brake lever when wheel is not installed.
Inspection: Every 30 days inspect all bolts for correct tightness and pads for thickness. Replace brake pads at your local bike shop if disc brake pads are thinner than 1mm. Pushing the brake lever will push the pads against the disc. The friction will cause the bike to slow down. (Figure DB2).

Disc Brakes: Braking in period

• Please note that brand new disc brakes need “braking in”. This means it may take a few weeks until they perform optimaly. Ride your bike very carefully and allow plenty of time for braking.
• Before each ride, make sure that both front and rear brakes work well and follow the guide below to maintain the brakes.

Changing Brake pads: Remove wheel or remove brake calliper by loosening centering bolts. Remove pads and replace with new brake pads. Re-install wheel or tighten centering bolts in correct position.
WARNING! Keep brake pads and brake rotor free from oil. Do not touch with your hand as it will transfer grease. Failure to do so may prevent the brakes from operating properly and cause serious injury or death.

Brake Levers
The brake line is attached to the lever and pressing the lever (moving the lever closer to the handlebar using your hand) will activate the brakes. Brake levers are attached with a lever clamp bolt and it should be tightened to 7 Nm.

To install a gear cable
Locate the ball end of the cable in the gear shifter. Memorize cable path along bike, loosen the cable-clamp and remove the old cable. Apply grease to the part of the new cable which is inside the outer brake cable housing. Thread new cable through housing. Check that the end of the cable with the ball is installed correctly in the shifter. Check that the housing is positioned in the housing stop of the shifter. Adjust derailleur according to the respective section in this manual. Tighten cable-clamp bolt to 7Nm. Cable should be cut at about 1 ½ inches after cable-clamp. Cover the end of the cable with a cable cap to prevent fraying and injury.

Cables and electric wires
Check all cables monthly if there are any bends, cuts, frays or worn areas. Do not ride bike with damaged cables. Have damaged cables replaced.

Changing gears correctly

• Changing gears will allow you to pedal at a comfortable and constant rate. The external (derailleur) gears consist of different sizes of cogs on the rear wheel.
• Operating the gear shifter will move the chain to different cogs. The gear shifter is located on the right hand side handle bar. Only shift gears while pedalling forward. Decrease force on the pedals to allow smooth shifting.
• Do not shift gears when the bike is standing or going over bumps. The chain could fall off or jam.

The gear shifter has two controls (Figure G1):

• push the “plus button” to shift into a high gear (small cogs).
• Push and hold the LEVER for a moment to shift into a low gear (large cogs).
• Shifting to large rear cogs makes it easier to pedal and are recommended for example if you go uphill.
• Small rear cogs make it harder to pedal and can be used on the flat to allow to pedal comfortably when riding at higher speeds.
• Locate the gear clamp bolt which attaches gear shifter to handle-bar and tighten to 7Nm.
• The motor operates independently and is not affected by gear changes.

Tuning of the gears (rear derailleur)

• This is a general guide only. Your model may vary.
• If the gears don’t switch smoothly, they need adjustment.
• It is recommended to lubricate the chain with chain lubricant to insure optimal performance.
• The gears can be adjusted in most cases by turning the barrel (SIS cable adjuster) (1) by hand anti-clockwise in half turns until the gears switch smoothly. If that doesn’t help, it may be necessary to turn it clock wise.
• If that doesn’t help please refer to the detailed tuning instructions below and refer to third part video at http://www.youtube.com/watch?v=wQncKmddahk.

• shift into small cog
• turn barrel (SIS cable adjuster) all the way in clockwise
• adjust high gear screw (H) so that the Tension Pulley (Figure D2) is straight under the small cog (barely outward).
• release wire by turning anchor screw (4) anti-clockwise, gently pull wire tight, tighten anchor screw clock-wise to secure mechanical wire
• adjust barrel (anti-clockwise) until the chain shifts smoothly from the smallest gear to the second-smallest gear
• Shift into centre cog. Line up pulley using barrel barely inward of centre cog
• Shift to large cog. Adjust lower limit screw (L). Align pulley so that it can’t over-shift.
• If it’s still clicking turn lower limit screw out (anti-clockwise). Move pulley cogs close to derailleur with b-tension screw (pulley adjustment screw). This adjusts angle of derailleur.

REAR WHEEL
The rear wheel is installed into the rear fork with two nuts, one on the left and one on the right side of the wheel axle. Tighten LEFT and RIGHT rear wheel nuts (7 and 12) to 30 Nm. This is a general guide only. Your model may vary.

Removal of rear wheel

Caution! This is a general guide only, your model may vary. Take care not to damage the wire and pins at end of connector (3). Do not bend wire with force where it enters rear axle (8). To replace damaged wires the whole motor needs to be replaced.

Figure RR1 (right side of bike at rear wheel):
To remove rear wheel, first disconnect male end of motor wire (3) from female end of motor wire (2) by carefully pulling in the directions of the arrows shown . Cut cable ties (1) if they are in the way. Then, carefully remove male end of motor wire (3) from the cable attachment guides (4).

Figure RR2 (RIGHT side of bike, at centre of rear wheel):
Remove rubber cap (9) from rear axle (8) to expose RIGHT rear wheel nut (7). This figure shows a rubber cap which has already been removed. Use a wrench to loosen RIGHT rear wheel nut (7). If you are having trouble to access the nut (7), remove bolts 5 and 6 which allows to remove derailleur guard (10).

Figure RR3 (LEFT side of bike, at centre of rear wheel):
Remove rubber cap (14) from rear axle (13) to expose LEFT rear wheel nut (12). This figure shows a rubber cap which has already been removed. Use a wrench to loosen LEFT rear wheel nut (12). The wheel can now be removed. Remove bolt 11 if you are having trouble to access bolt 12.

Figure RR4. Correct installation of rear axle into fork. View from bottom UP.
To re-install rear wheel, place chain into one of the cogs on the rear wheel, then carefully insert the rear wheel axle into the fork following the instructions below.
15 Inner washer, 16 Key (small protrusion) of inner washer, 17 Rear fork, 18 Opening of rear fork to insert rear wheel axle, 19 rear wheel axle, 20 rear wheel nut. When installing the rear axle (19) into fork it is very important to make sure that the inner washer (15) is located at the inner side of the fork. The Key (small protrusion) of the inner washer (16) needs to protrude into the opening of the rear fork (18). The axle needs to be fully inserted into the fork, then the nut (20) needs to be tightened to 30 Nm. Also tighten nut on other side of rear wheel axle

Figure RR5. To re-install rear wheel, follow steps shown in Figure RR3, RR2 and RR1 in reverse order. Make sure the wheel is installed safely. When re- connecting the male and female motor wire, first make sure that both arrows on the wires are aligned, then push both cables together all the way as shown in this figure.

WARNING! Ensure male and female connector are pushed together all the way. If the connection is loose, it may lead to heat build-up, melting connections and damage to motor, controller and bike. During first ride after re-installing rear-wheel check connection regularly for heat build-up and push together if necessary.
WARNING! Ensure rear wheel is installed safely before riding. If wheel becomes loose during riding it may cause you to fall.

Rim, Tyres and Tubes

• Figure T1: Cross-section of tyre and rim: 1: rim, 2: rim strip, 3: rim braking surface, 4: bead core, 5: inner tube, 6: casing, 7: tread. Image source: Wikipedia, Author Deerwood.
• Wheels: When changing a tyre or tube make sure that a rim strip is installed covering all spoke holes and nipples to protect the tube from puncture. Inspect the spokes and make sure the wheel is not wobbly. Clean rims every month with a moist rag and water to allow rim brakes to perform well. Check the rim for wear every month. Replace rim if it is worn or has signs of damage. To check wheel hub bearings lift wheel off ground and spin it by hand. There should be no unusual noise. Try to move wheel left and right. The bearings shouldn’t be loose. If there are issues have wheel replaced or repaired by a professional.
• WARNING! A worn rim may cause the wheel to malfunction while riding causing you to fall. If the rim forms part of a braking system, rim wear may cause brake failure.
• The tyre size can be found on the tyre side wall. Replacing tyres: Standard tyres consist of an outer tyre and a separate inner tube (Figure T1). If the tube is punctured it needs to be replaced or patched. Make sure replacement tube and tire are the same size as marked on the old tire/tube. To remove tyres use your hands or a suitable tyre lever available at bike shops. Do not use sharp objects like a screwdriver as they may damage the rim, tyre and tube. To remove a wheel follow the instructions in this manual. Rim brakes need to be released first to allow wheel to be removed. To remove tyre and tube, fully deflate inner tube and move tyre bead to centre of rim. Use tyre levers to lift one bead core across the rim. Start opposite the valve as the valve will be in your way. You may have to use three levers. Take care not to damage tyre or tube. Do this around the whole wheel until one bead is completely outside the rim. Remove tube, then remove second bead from rim.
• To install tyres and new tube, first carefully check the rim for any damage, cracks or sharp objects. Make sure rim strip is installed correctly. Inflate tube until it takes shape, however don’t fully inflate it. Place it inside tyre, insert valve stem through opening in rim and insert one bead using your hands into the rim around the whole wheel. Take care not to damage the tube. Then, using your hands push the tube into the centre of the rim around the whole wheel. Insert second bead into rim by hand. If it is too difficult, carefully use tyre lever without pinching the tube. Push stem of valve through opening in rim and inflate tyre to half pressure. Check around wheel if tube is correctly on inside and tyre on outside. Adjust if necessary. Deflate tube again to prevent pinching. Finally inflate to pressure recommended on tyre wall (e.g. Minimum 40psi, Maximum 65psi) using a hand bicycle pump. See conversion table psi/kPa in this manual.

The frameset (frame and fork)

• The frame is an important part of the bike to which many parts such as the rear wheel, fork and seatpost attach. It is critical to make sure that the frame is in good condition.
• If suspension is installed into the frame refer to the respective section of this manual for suspension maintenance.
• If your fork has knobs to adjust the stiffness, turn the knob in the direction of the arrows shown towards the “+” symbol for stiffness, towards “-” for softness. The fork must not compress fully while riding.
• If your fork has a “lock” button or dial, turn the button or dial towards the lock symbol or lock text to lock it into place. The fork will then be rigid and not provide suspension.
• Do not expose frame to heat over 158° Fahrenheit (70° Celcius).
• Only clean with damp, soft rag, mild detergent and water. Only use small amounts of water to make rag damp.
• Avoid water intrusion into electrical components. Do not spray the bike with water, high pressure cleaners or immerse into water.
• Do not use corrosive or harsh chemicals. After cleaning wipe damp parts with dry, clean rag.
• Only use original seatposts with correct diameter, length and correct minimum insertion marks. Installation of seatpost with incorrect diameters, excessive length or too short minimum insertion marks can damage the frame.
• When installing parts into threads on the frame make sure the correct parts are used and that the threads on the frame are not damaged, e.g. by over- or under-tightening. Clean all threads before installation, and insert components at correct angle carefully by hand. If there is too much resistance installing a part it may indicate cross-threading. Un-screw part, re-align and then re-insert. Only use tools to tighten part after it has been fully inserted into thread by hand.
• Do not try to adjust frame by bending. Damaged frames and forks should be reported and need to be replaced or repaired.
• Inspection: Check of the frame and fork before each ride for scratches, deformation, chips or any other signs of damage. Inspect fork in detail every year during headset service. This should be done by a bike professional.

BATTERY: Installation and using the keys

Figure B2. To remove the battery, hold the battery with one hand, insert the key into the battery lock with the other hand and turn clockwise. Then carefully remove the battery from its base by moving the battery in the direction of the arrows shown.
To install the battery follow the steps in reverse. Handle the battery with care. Ensure that the battery is installed firmly and locked before moving or riding the bike. Do not use force to avoid damage to the electric components. Do not drop the battery. Do not lose your keys as they are unique and cannot be easily replaced.

Charging the battery

• The battery can be charged on or off the bike.
• Charging temperature between 10 ℃ (50 °F ) and 30℃ (86 °F).
• During charging the temperature may increase to about 50 ℃ (122 °F).
• Stop charging battery if it gets unusually hot and contact customer service. Charge indoors undercover in dry area. Do not charge outdoors.
• Only use original supplied charger to avoid overheating, bursting or ignition.
• The charger is a smart charger, which means it will automatically stop charging when the battery is full.
• The battery takes about 5-7 hours to charge if It’s completely discharged.
• At first charge, it can take longer since battery pack is balancing.
• If battery does not fully charge within 8 hours, disconnect charger and contact customer service.
• If it’s not fully discharged it will take less time to charge.
• Disconnect charger after charging. Unplug charger from electricity grid if not in use.

Figure B5: Charging the battery (Illustration)
Connect the power cord (5) firmly to the power socket on the charger (6). Gently remove rubber dust cover (9) to expose battery input socket (8). Then connect the charger output cable (7) to the battery input socket (8) on the battery. The LAST step is to connect the power plug (10) to the wall power point (AC, 110/220 Volt, 50/60Hz) (4).
WARNING! To prevent electric shock connect power plug (10) to wall socket (4) as LAST step. Do not open charger. Voltage is detected automatically. Do not yank cables. Pull on plugs, not on cables.

Lights on Charger

• If there are TWO LIGHTS on the charger. BOTH LIGHTS RED: Charging.
• ONE LIGHT GREEN and ONE LIGHT RED: Fully charged or not connected.
• If there is ONE LIGHT on the charger: RED: Charging. GREEN: Fully charged.

WARNING! The charger can get very hot while charging. Always keep it away from material which can catch fire. Do not cover charger. If there are any signs of smell, smoke or melted plastic or unusual noises, immediately disconnect charger from power socket and do not use charger again. Always attend charger during charging. Keep away from water, moisture, children and pets. Follow instructions contained on the label of the charger.

Battery Care & Storage

• Charge battery before first ride and after every ride.
• It is not necessary to fully discharge battery before charging. Lithium-ion batteries do not have any memory effect, so you can charge them at any time.
• Lithium-ion batteries must not be stored if fully discharged. If your battery is fully discharged, charge it immediately. Storing the battery if fully discharged for more than 1 day will damage the battery.
• Store the battery fully charged and then charge it at least once a month. It is not necessary to leave the charger connected to the battery if stored for long periods. Just top the charge up every month. If batteries are not charged at least every month, the battery may be damaged and such damage is not covered under warranty. Disconnect charger after battery is fully charged.
• Store battery between 10 ℃ (50 °F ) and 20℃ (68 °F) in a clean, dry place away from sunlight. Do not store with hazardous, corrosive or flammable substances. Do not expose batteries to heat or fire. Store batteries in fire-proof environment.
• Operating temperature range during discharge is 5℃ (41 °F ) to 50℃ (122 °F). Do not leave the battery inside car, in direct sunlight or any other hot places. If battery is charged at temperatures lower than 5 ℃ (41 °F ), the range of battery will be reduced.
• Do not disassemble, deform or modify any component of the battery or any other mechanical or electric part
• Do not connect the + and – terminals of battery with metallic objects. Do not store with metallic objects such as hairpins or necklaces as short circuits and burns may occur.
• Do not place into water, salt water and moisture.
• Do not throw battery or subject it to strong shocks.
• Inspect battery and terminals carefully every month for leakage, discoloration, cracks, damage, signs of melting or corrosion.
• If fluid leaks from the battery and gets into contact with your eyes or skin, wash affected area with clean water without rubbing your eyes or skin and visit a doctor immediately to reduce damage to eyes or skin.
• Never handle battery or charger if parts are wet. Dry it thoroughly before usage to avoid electric shock.
• Store out of reach of pets and children.
• Always handle carefully with 2 hands.
• If errors occur, stop using battery, consult manual or contact customer service.
• Discard batteries according to your local battery disposal guidelines.
• Do not use the battery inappropriately. Only use for the intended purpose with the original product.
• It is recommended to purchase a fire extinguisher which can be used with Lithium-ion battery fires.

WARNING! If a battery is stored for longer than 1 month without charging it, it may get damaged.
WARNING! Lithium-ion batteries may leak, ignite and burst if not handled properly!
WARNING! Always remove the battery during bike maintenance

Battery range

• Battery range is how far you can travel on one full battery charge.
• It depends on a lot of factors including weight of rider, weight of luggage carried on bike, the amount of pedalling, the level of pedal assistance selected on the display, the terrain (hills or flat), tyre pressure, brake adjustment and wheel bearings. It is impossible to provide an exact range for a battery.
• Riding the bike using the throttle only will consume battery faster and the maximum distance per charge will be reduced.
• The more the rider pedals, the longer the distance from one battery charge.
• Batteries are consumable items and range deteriorates naturally over time and with usage. After some time batteries will naturally die and need replacement.
• A new, fully charged 10Ah 36V battery on a bike with a 250W motor has a typical range between 20 to 50 km. This range estimate is not guaranteed and more or less distance can be travelled, depending on the conditions.
• It is recommended to ride conservatively in the beginning. Familiarize your self with the range to avoiding running out of battery. Operating the bike without motor assistance requires pedalling with more effort pedalling and since electric bikes are heavier as compared to non-electric bicycles.
• To extend your range reduce luggage weight, use LOW pedal assistance, pedal harder, avoid steep hills, avoid sudden stops, accelerate slowly and make sure that:
• Tire pressure is at least the minimum recommended as printed on the side of the tire. The higher the tire pressure, the longer the range. Do not exceed the maximum tire pressure. CAUTION: changes in the tire pressure may affect the handling of the bike.
• Ride carefully to get used to different tire pressures.
• The brakes do not rub against the wheel. While the bike is stationary, lift off each wheel from the ground and spin it – listen closely if there is a rubbing noise. Spin the wheel and observe if the wheel comes to an abrupt stop which indicates rubbing. If needed adjust brakes.
• Lubricate your chain to reduce friction while pedalling

LIMITED WARRANTY

LIMITED WARRANTY and Terms and Conditions Summary PLEASE KEEP YOUR PROOF OF PURCHASE

The following parts are warranted to be free from manufacturer’s faults for a period of 1 year (12 months) starting at the date of purchase: battery, motor, fork, headset, seat post, saddle, rims, kickstand, reflectors, wheel hub, controller, brakes, lights, bottom bracket, crank set, pedals, cassette, derailleur, shifter, LCD display, handle-stem, handlebar, charger, throttle. 2 years for the frame.
This limited warranty does not cover normal wear and tear items including but not limited to tires, inner tubes, cables, spokes or any damage, failure, or loss caused by improper assembly, set up, storage, or maintenance. Thiswarrantycoversnormaluseonly.Itdoesnotcoverdamage to the theproductduetomisuse,neglect,accidentorimproperservice. Commercial use, including but not limited to couriers, bike rentals, flyer deliver and food delivery will void the warranty. Any modification of the product without authorization of Leitner will void the warranty. Warranty is for the original purchaser only. Warranty is not transferrable to second hand users. It is the customers’ responsibility to service and maintain the products regularly and to make sure that the product is safe to use before each ride. Leitner does not accept claims for repairs which were performed without our written approval. Leitner does not assume any liability to the extent permitted by the law. For full terms and conditions please visit Leitner.com.au. Leitner reserves the right to change warranty terms without notice.

Recommended Torque values in Newton Meter (Nm) unit

• Unit conversion: 1Nm = 8.85 Inch-Pounds
• Bolts attaching brake lever, throttle and gear shifter to handle-bar: 7 Nm
• Steerer-clamp bolts on handle-stem: 10-15 Nm, Figure HS1
• Other bolts on handle-stem: 10 Nm
• Quick release lever attaching seat post to frame: 15 Nm.
• Brakes: calliper mounting bolts: 15 Nm, Centering bolts: 12 Nm Disc mounting bolt 8 Nm, Figure DB1
• Front wheel quick release: Measurement unit in pounds, not Newton Meter: between 12 pounds and 45 pounds
• Rear wheel nuts: 30-35 Nm, Figure RR4.
• Pedals to crank arm: 40 Nm
• Crank arm to bottom bracket: 40 Nm
• Bolts on rear rack: 16 Nm
• Seat Rail fixing bolt : 18-20 Nm, Figure S1.
• Cable anchor screw at rear derailleur: 7 Nm, Figure D1

Lubrication

Please find short instructions for lubrication below. Suitable grease and oil should be purchased from local bike shops. For further information please contact us. Wipe off any excess oil or grease. Make sure no lubricant is present on parts where it doesn’t belong.

• Chain: Every month. Use a rag underneath chain to avoid oil spilling onto other parts and use the rag to wipe off excess chain oil after lubrication.
• Quill type stem: Every year. Remove stem then remove grease from wedge. Apply thin layer of grease to wedge and the part of stem which is inside frame. Re-install stem
• Seatpost: Every year remove seatpost, then remove grease from seatpost. Apply thin layer of grease to the part of seatpost which is inside frame. Re-install seatpost
• Pedal threads on pedal axle where they insert into crank arms: Every year. Refer to pedal installation section of this manual to remove pedals, then remove grease from pedal axle. Apply thin layer of grease to the threads. Re-install pedals according to manual.
• Derailleur: Every month. Apply grease to all pivot points including the pulley.
• Brake lever pivots and brake arm fixing pivots: every 3 months.
• Quick release lever: Every year. Apply light oil to lever where it turns inside the body.
• Suspension fork: Every month remove old visible grease and apply a thin layer of grease to visible part of fork where it moves up and down due to suspension.
• Brake cable and gear cable: Lubricate when installing it.

The following parts should be lubricated by a local bicycle professional

• Bottom bracket bearings: Every year
• Direct connect stem: Every year
• Headset bearings: Every year
• Wheel bearings: Every year
• Oil inside Oil suspension fork: Every year.

DO NOT LUBRICATE: Rear suspension shock or pivots, brake pads, wheel rims, brake discs, pedal surface.

Conversion Table psi/kPa

Accessories

Check your accessories, for example mudguards, lights, kickstand, rack, chainguard every 30 days and adjust attachment and alignment if necessary. The rear rack is not centered however this does not affect the function of the bike.

Parts of an electric bike

Basic trouble-shooting guide

although      there       is power to Display

| 1) Brakes are engaged

2. Loose motor wire connector

3. Loose wire 4)Broken wire

5)pedal assist sensor faulty

| 1) Disengage brakes

2)  Check motor wire connector

3)  Check all connectors

4)  Inspect all wires

5)  Replace throttle or pedal assist sensor

2| Bike does not work

(no power to display)

| 1)Battery not installed correctly 2)Battery empty

3)Battery not switched on 4)LCD Display not switched on 5)Loose connections

6)Fuse blown

| 1)  Install Battery correctly

2)  Charge battery

3)  Switch battery on

4)  Switch display on

5)  Check all wire connections

6)  Replace fuse

3| Bike has reduced

speed and/or range

| 1) Low batteries 2)Faulty batteries 3)Low tire pressure

4. Brakes dragging against rim or disc

| 1) Charge batteries for

recommended time

2)  Replace batteries 3)Inflate tires to recommended pressure

4. Adjust brakes and/or rim

4| Bicycle has

intermittent power

| 1) Loose connectors

2)  Loose fuse

3)  Damaged wire

| 1)  Check all connectors

2)  Check fuse connector

3)  Inspect all wires

5| Charger light does

not operate

| 1)Power outlet faulty 2)Charger is not plugged to wall or battery properly

3)Charger light or charger is faulty

| 1)  Try another outlet

2)  Check all plugs

3)  Replace charger

6| Charger completes

charging in an unusually short

amount of time

| 1)  Faulty charger

2)  Faulty battery

| 1)  Replace charger

2)  Replace battery

7| Strange noise

from wheel and motor

| 1) High-pitched “ticking” noise due to loose spokes which disappears when wheel is off ground and spun by hand

2. Motor internal gears damaged 3)Motor damaged

4)Loose bolts

| 1)       Adjust spoke tension

2)       Replace internal motor gears

3)       Replace motor

4)       Tighten all bolts

Unlocking the throttle to accelerate to approximately 25km/h

IMPORTANT LEGAL NOTE
Leitner electric bikes are built to comply with Australian electric bike rules. For 250 watt bikes, this means that the throttle speed is limited to “walking speed”, around 6km/h in the factory setting.
Many customers were asking for a throttle which allows the bike to go around 25km/h without pedalling. We have included a feature in Leitner electric bike models to unlock the throttle as described below.
WARNING! After unlocking the throttle your eBike will no longer comply with the Australian eBike law and may be illegal in your state for use on roads. Therefore the bike must NOT be used on public roads if the throttle is unlocked. The bikes must only be used on private property or other OFF ROAD locations where it is legal to use such a bike.
If you ride a 250w bike with the unlocked throttle on public roads you may receive heavy fines for riding “a motorbike without registration and license”. We would like you to be aware of this and Leitner does under no circumstances take any liability for any issues involving riding a bike with unlocked throttle illegally.

Procedure to unlock the throttle.
Watch the video https://youtu.be/dZCuBgvSKNU.

Please note for bikes equipped with LCD displays it is NOT required to access the controller. Simply follow the procedure below to unlock the throttle. Refer to Figure C2 and Figure C3 for further information about the LCD display and its function.

• Switch battery ON
• Switch LCD Display ON
• Push and hold the “+” and “-” button at the same time until the screen changes
• AGAIN push and hold the “+” and “-” button at the same time until you see “P5” on the screen
• Push the “i” button to cycle to the next digit
• Use the “+” button to increase the numbers e.g. from 0 to 1. Program the display to show the number 0510, then push the “i’ button
• The screen will show “VOL”.
• Push the “+” button until you see “Hnd”
• Push the “i” button briefly until HL-y is displayed
• Push the “+” button briefly until HL-n is displayed
• Push and hold the “i” button
• Again push and hold the “i” button

Enjoy your bike with the unlocked throttle. Do NOT ride on public roads.

The controller

The controller is the “brain” of the ebike. All wires are connected to it and the controller controls all functions of the bike including the speed limits.
WARNING! Switch off and remove the battery from the bike before accessing the controller to avoid accidental short circuits. Wear personal protective protective equipment like safety glasses. Handle wires with care and don’t use force to avoid damaging the wires. If you don’t feel comfortable with these instructions have the procedure performed by a skilled ebike technician.

References

• Leitner Electric Bikes and Folding Electric Bikes Australia – Leitner Electric Bikes Australia
• Electric Bike Manual - Leitner – Leitner Electric Bikes Australia
• Leitner Electric Bikes and Folding Electric Bikes Australia – Leitner Electric Bikes Australia
• Leitner Electric Bikes and Folding Electric Bikes Australia – Leitner Electric Bikes Australia
• Electric Bike Manual - Leitner – Leitner Electric Bikes Australia

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>